132

This aluminum salt derived from distilled, hydrogenated fatty acids is designed for protective and decorative coatings. Has the highest free fatty acid content and lowest aluminum metal content.

This product has strong lubrication characteristics, thickening ability, thermal stability, and water-repellent characteristics. Total Ash: 5.50 – 7.50 Fineness % Thru 20 Mesh: 100.00 (Min) Fineness % Thru 200 Mesh: 90.00 – 100.00 Free Fatty Acids (As Stearic): 25.0 – 35.0 Water: 0.00 – 1.00 Water Soluble Salts: 0.00 – 1.00 Yields the lowest viscosity increase. Great for dry lubrication and thickening of ink manufacture. It is commonly used in the production of coatings(protective and decorative) such as paints, enamels, varnishes, and lacquers. additionally, it acts as a dry lubricant in metal processing and as a water repellents.

30

The aluminum salt of distilled, hydrogenated fatty acids.

This product has strong lubrication characteristics, thickening ability, thermal stability, and water-repellent characteristics. Appearance: white powder Melting Point: 160 °C Insoluble in H2O Great for protective and decorative coating preservation. Great for thickening of aromatic solvents in inks.

ALKANOX™ 240 Granular

Low volatility phosphite antioxidant that effectively prevents processing-induced oxidative degradation in a wide variety of polymers.

ALKANOX™ 240 Granular effectively reduces peroxide induced oxidative degradation during processing in a wide variety of polymers. It's low volatility makes it effective even in high temperature processing. Particularly effective in Polyolefins, polycarbonate, ABS, and polyesters. Appearance: White, free-flowing powder Molecular Weight: 647 g/mol Bulk Density: 530 (kg/m3) Melting Point: 182-188 °C Prevents processing-induced degradation Effective at high temperatures Broad food-contact approvals Excellent hydrolytic stability Non-dusting

ALKANOX™ 240 Powder

Low volatility phosphite antioxidant that effectively prevents processing-induced oxidative degradation in a wide variety of polymers.

ALKANOX™ 240 Powder reduces peroxide induced oxidative degradation during processing in a wide variety of polymers. It's low volatility makes it effective even in high temperature processing. Particularly effective in Polyolefins, polycarbonate, ABS, and polyesters. Appearance: White, free-flowing powder Molecular Weight: 647 g/mol Bulk Density: 550 (kg/m3) Melting Point: 182-188 °C Prevents processing-induced degradation Effective at high temperatures Broad food-contact approvals Excellent hydrolytic stability

ANOX™ 1315

Low viscosity liquid phenolic antioxidant with some FDA approvals.

ANOX™ 1315 is a highly effective, non-discoloring, liquid antioxidant. It is ideal for a variety of polymers, engine and cutting lubricating oils, and polyols used in polyurethane foams for both storage and scorch protection. Appearance: Viscous, clear yellow liquid Melting Point: -56 °C Specificity Gravity (@ 20 °C): 0.94 g/cm³ Viscosity (@30 °C): ~200 mPa · s Flash Point: 229 °C Liquid form FDA approvals for use in specific polymers Low viscosity allows for extra easy handling High antioxidant efficiency in many different polymers including polyolefins, synthetic rubbers, PVC, polyols (PU) and lubricant oils

ANOX™ 20 Granular

High molecular weight hindered phenolic primary antioxidant. Effective as a process stabilizer, but is especially powerful at preventing polymer degradation during long-term aging. Similar to ANOX™ 20 Powder, but in granular form.

ANOX™ 20 Granular is a high molecular weight hindered phenolic antioxidant that primarily functions as a polymer stabilizer preventing degradation in long-term aging. Also provides defense against polymer degradation and discoloration during processing. Ethanox 310 has been rebranded to ANOX™ 20. Appearance: White free-flowing powder Molecular Weight: 1178 g/mol Bulk Density: 570 kg/m3 Melting Point: 110-125 °C Flash Point: 299 °C Non-blooming Excellent resistance to extraction from polymer compounds Synergizes with phosphites like Alkanox 240, Weston 705, and TNPP Prevents processing-induced degradation AND degradation from long-term aging Prevents discoloration at high processing temperatures Broad food-contact approvals CAS equivalent to Ethanox 310 and Irganox 1010 Available in powder, granular, non-dusting pellet form, alone and in binary blends Food packaging, automotive underhood, wire and cable

ANOX™ 29

Phenolic antioxidant that protects against thermo-oxidative degradation during processing, storage and end-use in a wide variety of materials.

ANOX™ 29 is a sterically hindered phenolic antioxidant that is tremendously effective in a wide variety of materials at preventing thermo-oxidative degradation during processing, storage, and end-use. Synergizes with thioesters to offer enhanced thermal aging properties in polypropylene. Appearance: White to off-white, free flowing, crystalline powder Softening Point: 161 -164 °C Flash Point: > 193 °C Molecular Weight: 438.7 g/mol Bulk Density: 0.56 g/cm³ Synergizes with thioester antioxidants to enhance thermal aging properties in polypropylene Elastomers such as EPDM, SBS, and rubber blends with polyolefins, natural and synthetic tackifier resins, crystalline and high impact polystyrene, ABS terpolymer, waxes and oils

ANOX™ BB011 Granular

Synergistic blend of granular form phenolic and phosphite antioxidants to protect polymers both during processing and long term aging.

ANOX™ BB011 Granular is a solid, synergistic blend of equal parts phenolic (ANOX™ 20) and phosphite (ANOX™ 240) antioxidants. This binary blend provides excellent protection for polymers during both processing and long term aging. Appearance: White to off-white granules ALKANOX™ 240 Content: 47.5-52.5% ANOX™ 20 Content: 47.5-52.5% Clarity of Sol (10% w/v Toluene): Clear Tran. 425 nm (10% w/v Toluene): >=95.0% Tran 500 nm (10% w/v Toluene): >=97.0% Fewer additives to dose properly Non-dusting Low volatility allows for higher processing temperatures Excellent resistance to extraction from polymer compounds Used in a wide variety of thermoplastic polymers such as polyolefins, polycarbonates, ABS, and polyesters

ANOX™ BB011 Powder

Synergistic blend of powder form phenolic and phosphite antioxidants to protect polymers both during processing and long term aging.

ANOX™ BB011 Powder is a solid, synergistic blend of equal parts phenolic (ANOX® 20) and phosphite (ALKANOX® 240) antioxidants. This binary blend provides excellent protection for polymers during both processing and long term aging. Appearance: White to off-white powder ALKANOX® 240 Content: 47.5-52.5% ANOX® 20 Content: 47.5-52.5% Clarity of Sol (10% w/v Toluene): Clear Tran. 425 nm (10% w/v Toluene): >=95.0% Tran. 500 nm (10% w/v Toluene): >= 97.0% Fewer additives to dose properly Low volatility allows for higher processing temperatures Excellent resistance to extraction from polymer compounds Used in a wide variety of thermoplastic polymers such as polyolefins, polycarbonates, ABS, and polyesters

ANOX™ BB021

Synergistic blend of phenolic and phosphite antioxidants to protect polymers both during processing and long term aging.

ANOX™ BB021 Powder is a solid, synergistic blend of one part phenolic (ANOX® 20) to two parts phosphite (ALKANOX® 240) antioxidants. This binary blend provides excellent protection for polymers during both processing and long term aging. Appearance: White to off-white powder ALKANOX™ 240 Content: 64.2-69.2% ANOX™ 20 Content: 30.8-35.8% Clarity of Sol (10% w/v Toluene): Clear Tran. 425 nm (10% w/v Toluene): ≥95.0 Tran. 500 nm (10% w/v Toluene): ≥97.0 Fewer additives to dose properly Low volatility allows for higher processing temperatures Excellent resistance to extraction from polymer compounds Available in powder and granular forms Used in a wide variety of thermoplastic polymers such as polyolefins, polycarbonates, ABS, and polyesters

ANOX™ PP18 NDB

High molecular weight hindered phenolic antioxidant, provides effective protection against polymer degradation during processing and in long term aging in many polymer systems.

ANOX™ PP18 stabilizer effectively reduces oxidative degradation of most polymers during processing and end-use application. It is ideal for polyolefins, styrenics, block co-polymers, elastomers, adhesives, PVC, and polyurethanes. It is available in granular, powder, and non-dusting blend form. Appearance: White pellets Melting Point: 50-55 °C Flash Point: 273 °C Molecular Weight: 531 g/mol Non-dusting Broad food-contact approvals

Armoslip 18 LF Beads

Armoslip 18 LF beads are stearamides with typical usage in caps and closures or in rubbers and inks

These fatty amides provide a range of plastic additives, wax additives and lubricants to various plastics applications Free Fatty Acid .05% Max (as Stearic Acid) Assay 98.5% Min Moisture 0.1% Max Iodine value (g I₂/100 g): 3 max Melting point: 99-109°C Excellent anti-blocking activity Facilitates over-printing and wet-printing Water soluble

Armoslip E, Beads

Armoslip E beads are formulated from refined rapeseed oil and offers excellent slip effects and provides good anti-blocking performance

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Assay 98.5% Min Free Fatty Acid Content 0.2% Max Moisture 0.05% Max Iodine Value 74 Min 79 Max (g I₂/100 g Melting point 80-84°C Rapeseed oil based Low volatility and high temperature stability

Armoslip® CP - Beads

Armoslip® CP is formulated from refined oleamides and provides excellent slip effect and has a moderate performance when used for anti-blocking

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Iodine Value 84 Moisture .25% Max Amide 98% Min Bead form allows for easy transportation Insoluble in water

BHT

Butylated Hydroxy Toluene is a non-staining, hindered phenolic antioxidant commonly used in a wide variety of applications including plastics, elastomers, petroleum products, and food. Available in several physical forms, including crystalline.

Sasol's Butylated Hydroxy Toluene (BHT) is a food grade, low molecular weight, hindered phenolic antioxidant that reduces degradation initiated by heat, light, and time in organic materials. BHT is the most prevalent and approved antioxidant in the world. Appearance: White crystal Specific Gravity @ 60 °F: 1.01 Flash Point (Closed Cup): 245 °F Bulk Density: 37.5 lb/ft³ Purity: 99% minimum Freezing Point: 156.56 °F Color, Molten (APHA): 50 maximum Ash, Residue on Ignition: 0.002% maximum Arsenic: 3 ppm Heavy Metals as Lead: 10 ppm Molecular Weight: 220.34 g/mol Soluble: Methyl alcohol, isopropyl alcohol, ethyl alcohol, benzene, methyl ethyl ketone, petroleum ether, mineral oil, linseed oil, lard Insoluble: Sodium hydroxide, water Food grade Kosher and Halal certified Polyols, polybutylene, hydrocarbon resins, block copolymer elastomers, industrial fats, fatty acids, transmission fluids, lard, shortening, tallow, animal feeds, vegetable oils

BHT, Free Flow

Butylated Hydroxy Toluene is a non-staining, hindered phenolic antioxidant commonly used in a wide variety of applications including plastics, elastomers, petroleum products, and food. Available in several physical forms, including free-flowing spherical particles.

Sasol's Butylated Hydroxy Toluene (BHT) is a food grade, low molecular weight, hindered phenolic antioxidant that reduces degradation initiated by heat, light, and time in organic materials. BHT is the most prevalent and approved antioxidant in the world. Appearance: White crystal Specific Gravity @ 60 °F: 1.01 Flash Point (Closed Cup): 245 °F Bulk Density: 37.5 lb/ft³ Purity: 99% minimum Freezing Point: 156.56 °F Color, Molten (APHA): 50 maximum Ash, Residue on Ignition: 0.002% maximum Arsenic: 3 ppm Heavy Metals as Lead: 10 ppm Molecular Weight: 220.34 g/mol Soluble: Methyl alcohol, isopropyl alcohol, ethyl alcohol, benzene, methyl ethyl ketone, petroleum ether, mineral oil, linseed oil, lard Insoluble: Sodium hydroxide, water Food grade Kosher and Halal certified Polyols, polybutylene, hydrocarbon resins, block copolymer elastomers, industrial fats, fatty acids, transmission fluids, lard, shortening, tallow, animal feeds, vegetable oils

BIK™ OT

Activator for blowing agents and accelerators that lowers the decomposition temperature of AZ type blowing agents.

BIK™ OT is a surface treated urea used as an activator for thiazole, thiuram and dithiocarbamate accelerators. It is an efffective promoter for Celogen AZ type blowing agents in SBR, butyl, EPDM, and neoprene and natural rubbers. Appearance: Fine white powder Specific Gravity: 1.31 Melting Point: 129-134 °C Soluble: Water (except for surface coating) Insoluble: Benzene, gasoline Reduces odor when used with nitrosamine-type blowing agents Promoter for AZ-type blowing agents in NR, SBR, IR, EPDM and CR rubbers Lowers the decomposition temperature of AZ-type blowing agents in cellular products Activator for thiuram, thiazole, and dithiocarbamate accelerators Relatively nonstaining Relatively nondiscoloring

BLE™ 25

Liquid form antioxidant and antiflex cracking agent for use in peroxide cured solid rubbers and latex.

BLE™ 25 stabilizer is a liquid antioxidant and antiflex cracking agent designed for Neoprene, nitrile rubbers, BR, EPDM, SBR and SBR lattices. This stabilizer can be dispersed and added to latex, or added directly to solid rubber. BLE™ 25 is non-blooming and has negligible effect on cure rate even when used with peroxide curing systems. Appearance: Dark brown, viscous liquid Specific Gravity: 1.09 Soluble: Acetone, benzene, ethylene dichloride Insoluble: Water, gasoline Can be used with peroxide curing systems Can be added directly to rubber Can be added in dispersion form to latex Non-blooming Negligible effect on cure rate Approved for food contact in rubber articles intended for repeated use (5% loading max) Liquid form Neoprene, nitrile rubbers, BR, SBR, and EPDM for tire tread, breaker, chafer, rim flange and carcass compounds.

BONDING AGENT P-1 WET

Adhesion promoter for predip polyester cord and resorcinol formaldehyde latex adhesives.

BONDING AGENT P-1 WET is an adhesion promoter that works by reacting isocyanate with water soluble epoxide to form a resinous coating on predip polyester tire and industrial cord. The resinous coating is now an active surface that resorcinol formaldehyde latex adhesives or chloroprene latex adhesives can bond to. Appearance: Off-white powder Specific Gravity @ 60 °C: 1.34 Physical Form: 68% active aqueous wetcake Melting Point: 187-200 °C Slightly Soluble: Dimethylformamide, acetonitrile, methyl ethyl ketone, cyclohexanone Insoluble: Water Allows adhesion between polyester cord and resorcinol formaldehyde latex adhesives or chloroprene latex adhesives Predip polyester tire and industrial cord

BroShield 21-B

General Purpose Brominated Flame Retardant

BroShield 21-B is a highly effective general purpose flame retardant for use in thermoplastics, engineering polymers, elastomers, thermosets, HIPS, polypropylene, EPDM , polyesters and epoxy. Appearance: White Powder Bromine Content: 81-82% Melt range (deg C): 348-353 Excellent Color Good UV stability High FR efficiency High thermal stability Non blooming RoHS compliant Elastomers Thermoplastics Engineered Polymers

BroShield 67-B

High purity non-diphenyl oxide.

BroShield 67-B is a brominated flame retardant with excellent thermal and UV stability for use in thermoplastics, thermosets and elastomers. BroShield 67-B is used in color sensitive applications and is non blooming. It also has excellent wet electrical properties which makes it ideal for wire & cable applications. Appearance: White to Off White powder Bromine: 65% Particle size,D50: 2 to 3 microns Melting Point: ≥ 445 °C Ph value: 4 to 5 Specific Gravity: 2.65 to 2.85 High purity Excellent thermal stability Good UV stability Coatings Adhesives Fabric back-coatings

BroShield BPS-70HP

Non blooming brominated flame retardant

BroShield BPS-70HP is a high purity brominated polystyrene flame retardant that has non blooming characteristics. It is used extensively in engineering resins, polyesters and polyamides. Appearance: White granules Bromine: ≥ 66% Volatiles Content: ≤ 0.2% Specific Gravity: 2.15 High purity Thermal stability Hydrolytic stability Excellent electric properties Non blooming Coatings Adhesives Sealants

BroShield RB4

Reactive halogenated flame retardant containing 68% bromine.

BroShield RB4 is a white crystalline powder containing 68% bromine. RB4 is primarily used to produce unsaturated polyester resins. Appearance: Off White Powder Bromine content: Off white powder Melting point: ≥ 270 °C Moisture: ≥ 0.20% Specific gravity: 2.90 High bromine content High purity Rigid foam Wire coatings Wool

C-1

Sodium stearate is a sodium salt of distilled hydrogenated fatty acids.

Sodium Stearate C-1 can be used in the wetting, thickening, emulsification, and opacification of creams, lotions, and shampoos. Custom mix of fatty acids, also seen used in deodorant sticks. Free fatty acids (as Stearic): 0.20-1.30 GLC-C16: 50.0-57.0 GLC-C18: 37.5-45.5 Water: 0.00-3.00 Fineness % thru 100 mesh: 30.0-100.0 FSC test: clear Unreacted caustic: pass Appearance, white powder: pass (visual) High solubility in hot polar solvents Soluble in hot mineral oils and waxes Forms gel upon cooling Available in powder form Sodium Stearate C-1 can be used in the wetting, thickening, emulsification, and opacification of creams, lotions, and shampoos.

C-7

Sodium Stearate is a sodium salt of distilled hydrogenated fatty acids.

Sodium Stearate C-7 can be used in the wetting, thickening, emulsification, and opacification of creams, lotions, and shampoos. May also be used for gelling agents in gel sticks. Free fatty acids (as Stearic): 0.20-1.30 GLC-C12: 0.00-0.75 GLC-C14: 0.00-3.00 GLC-C16: 23.0-30.0 GLC-C18: 35.0-40.0 GLC-C20: 17.00-24.00 GLC-C22: 12.00-16.00 GLC-C20 + C22: 30.00-40.00 GLC-Other: 0.00-4.00 Gel color and sediment: 0-150 Water: 0.00-3.00 Fineness % thru 100 mesh: 50.0-100.0 FSC test: clear Appearance, white powder: pass (visual) High solubility in hot polar solvents Soluble in hot mineral oils and waxes Forms gel upon cooling Low odor Available in powder form 100% vegetable based

Citroflex® 2

It also imparts improved light-fastness to lacquer formulations. In the personal care area, C-2 is used as a fixative for perfumes and as a plasticizer and film strengthening agent in hair sprays, nail polishes, and as an active in deodorants. Citroflex® 2 does not support fungal growth.

Citroflex® 2 or C-2 is recommended as a plasticizer for cellulosic derivatives as well as natural resins such as dammar and ester gums. Due to its limited oil solubility, grease resistance of polymers formulated with Citroflex® 2 is enhanced....

The lower molecular weight citric acid esters (Citroflex C-2, A-2, C-4, and A-4) have plasticization characteristics similar to those of the lower molecular weight phthalates, adipates, and sebacates in a variety of polymers. When used as an active in deodorant applications, Citroflex® 2 works by inhibiting esterase activity in bacteria. Appearance: Clear liquid Pour point, °C: -45 Viscosity @ 25°C, cps: 35 Specific gravity @ 25/25°C: 1.135 - 1.139 Medical plastics, personal care, HI&I, cellulosics, ink formulations, pesticide inerts, active for deodorants and antiperspirants

Citroflex® 4

support fungal growth.

Citroflex® 4 or C-4 is an excellent plasticizer for both cellulosic derivatives and vinyl resins. It provides improved light stability when used in cellulose acetate. It is also an excellent de-foaming agent in protein solutions. Citroflex® 4 does not...

The lower molecular weight citric acid esters (Citroflex C-2, A-2, C-4, and A-4) have plasticization characteristics similar to those of the lower molecular weight phthalates, adipates, and sebacates in a variety of polymers. Appearance: Clear liquid Pour point, °C: -62 Viscosity @ 25°C, cps: 32 Specific gravity @ 25/25°C: 1.037 - 1.045 Topical bandages, aluminum foil coatings, aerosol hair spray plasticizer, films, coatings, adhesives

Citroflex® A-2

is used as a fixative for perfumes and as a plasticizer and film strengthening agent in hair sprays, and nail polishes, as well as a component of various ink formulations.

Citroflex® A-2 is recommended for use with cellulosic derivatives. It offers low warping characteristics with cellulose acetate. It has been accepted for use as a plasticizer in food wrap films by the US Food & Drug Administration. Citroflex® A-2...

The lower molecular weight citric acid esters (Citroflex C-2, A-2, C-4, and A-4) have plasticization characteristics similar to those of the lower molecular weight phthalates, adipates, and sebacates in a variety of polymers. Appearance: Clear liquid Pour point, °C: -43 Viscosity @ 25°C, cps: 54 Specific gravity @ 25/25°C: 1.135 - 1.139 Low Molecular Weight Approved for food contact Biodegradable Medical plastics, personal care, cellulosics, ink formulations, defoaming agent

Citroflex® A-4

A-4 is effective in solution coating both paperboard and foil. It is an excellent plasticizer for vinyl toys. Citroflex® A-4 is also used as plasticizer for bio-plastics such as a poly lactic acid, cellulose acetate and poly hydroxyalkanoic acid.

Citroflex® A-4, also called Acetyltri-n-butyl Citrate, is widely used in children’s toys and food contact applications. It provides many improvements over di-butyl phthalate in cellulose nitrate films, including lower volatility, better resistance to yellowing, and better adhesion to metals. Citroflex®...

The lower molecular weight citric acid esters (Citroflex C-2, A-2, C-4, and A-4) have plasticization characteristics similar to those of the lower molecular weight phthalates, adipates, and sebacates in a variety of polymers. Appearance: Clear liquid Pour point, °C: -59 Viscosity @ 25°C, cps: 33 Specific gravity @ 25/25°C: 1.045 - 1.055 Low Volatility Better resistance to yellowing Better adhesion to metals Food contact products, children’s toys, animal ear tags, ink formulations, adhesives, pesticide inerts

Citroflex® B-6

blood products. It nearly duplicates the properties of di-(2-ethylhexyl) phthalate.

Citroflex® B-6 is a specially formulated citric acid ester for use in PVC medical articles such as tubing and intravenous bags where the content medium is aqueous-based. Citroflex® B-6 has low extractability into lipid media, making it particularly useful for...

Citroflex® esters are based on natural citric acid raw material, which is mainly derived from the fermentation of corn. The esters have a long history of use in food and beverage flavoring and in medical and pharmaceutical applications. Appearance: Clear liquid Pour point, °C: -55 Viscosity @ 25°C, cps: 28 Specific gravity @ 25/25°C: 0.991 - 0.995 The higher molecular weight citric acid esters, including Citroflex® A-4 and B-6 are effective replacements for DEHP (di-2-ethylhexyl) phthalate and DEHA (di-2-ethylhexyl) adipate. Medical plastics

Eastman DTBHQ Crystalline

Storage stability inhibitor - extends shelf life with minimum effects on gel time (unsaturated polyesters).

Eastman™ DTBHQ (2,5-ditert-butylhydroquinone) is a crystalline solid that has low vapor pressure and short induction periods in peroxide-catalyzed polymerizations. Insoluble in water and caustic solutions, used as an antioxidant or co-inhibitor to prevent oxidation and extend shelf life in many industrial applications. Appearance: White to tan crystals Flash point: 216°C (420°F) Melting point: 215°C (419°F) Boiling point: 321°C (610°F) Specific gravity: 1.07 CAS: 88-58-4 Scavenges radicals slowly Storage stability inhibitor with minimum effect in gel time Stabilizes against odor and color development Used as a stopping agent in rubber emulsions and anti-skinning agent in paints.

Eastman MTBHQ Dry

Secondary inhibitor (co-inhibitor) and antioxidant for nonfood fats and oils.

Eastman™ MTBHQ (mono t-butyl hydroquinone) is commonly used as a polymerization inhibitor and antioxidant in many industrial applications. Effective in higher temperatures due to its higher solubility and potency compared to unsubstituted hydroquinone. Appearance: Light tan solid Flash point: 171°C (340°F) Boiling point: 295°C (563°F) Melting point: 125°C (257°F) Specific gravity 20°C/20°C: 1.05 Molecular weight: 166.22 CAS: 1948-33-0 Very effective polymerization inhibitor Good performing antioxidant in unstable organic liquids Excellent performance as a heat and stabilizer for pressure-sensitiveness adhesives Used as a polymerization inhibitor and industrial antioxidant in many applications.

Eastman™ THQ Toluhydroquinone

Highly effective process inhibitor used in the production of highly reactive unsaturated polyesters.

Eastman™ THQ (Toluhydroquinone) is a tan to white crystalline solid that goes through similar chemical reactions as Hydroquinone. However, due to the presence of a methyl group in the ortho position, THQ becomes a highly active inhibitor in the free radical polymerization of vinyl monomers and unsaturated polyesters. Appearance: Off-white solid Flash point: 172°C (342°F) Boiling point: 279°C (534°F) Melting point: 127°C (261°F) Specific gravity: 1.3 Molecular weight: 124.13 CAS: 95-71-6 Better solubility in styrene than Hydroquinone Highly effective cook stabilizer in unsaturated polyesters Good performing antioxidant for oleates, linseed oil, and other nonfood fats and oils Used as an inhibitor, antioxidant, and intermediate manufacturing.

EGDS

A Glycol Stearate derived from vegetable feed stocks specifically for pearlescent agent applications.

This product is used in a variety of ways as anti-static agent, lubricant, and emulsifier. Acid Number: 0 - 6 mgKOH/g Free Ethylene Glycol: 0 - 0.3% Gardner Color: 0 - 2 Hydroxyl Value: 33 - 43 Iodine Value: 0 - 1 g I/100g Excellent stability Holds odor strength Great for compounds with high fat or wax contents.

Epolene® C-13 Polymer

Epolene® C-13 is a low density polyethylene with medium molecular weight and low color for use in adhesives, coatings, wax modification and plastic and rubber compounding.

Epolene® C-13 is a branched LDPE homopolymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-10 has a molecular weight of 76,000. Polymer Type: LDPE Molecular Weight: 76,000 Ring and Ball Softening Point: 110°C (ASTM E 28) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: MI=190 cP @ 190°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat stability Automotive refinish, wax modification,

Epolene® C-13P Polymer

Epolene® C-13P is a low density polyethylene powder with medium molecular weight and low color for use in adhesives, coatings, wax modification and plastic and rubber compounding.

Epolene® C-13P is a branched LDPE homopolymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-10 has a molecular weight of 76,000 and is the powder form of Epolene® C-13 Polymer Type: LDPE Product Form: Powder Molecular Weight: 76,000 Ring and Ball Softening Point: 110°C (ASTM E 28) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: MI=190 cP @ 190°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat stability Automotive refinish, wax modification,

Epolene® C-15 Polymer

Epolene® C-15 is a low density polyethylene polymer with medium molecular weight and low color for use in adhesives, coatings, wax modification and color concentrates.

Epolene® C-15 is a branched LDPE homopolymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-15 has a molecular weight of 17,000 and is provided in pellet form. Polymer Type: LDPE Molecular Weight: 17,000 Ring and Ball Softening Point: 101°C (ASTM E 28) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 1,800 cP @ 190°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat seal ability Packaging, automotive refinish, wax modification

Epolene® C-15P Polymer

Epolene® C-15P is a low density polyethylene powder with medium molecular weight and low color for use in adhesives, coatings, wax modification and color concentrates.

Epolene® C-15P is a branched LDPE homopolymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-15 has a molecular weight of 17,000 and is provided in powder form. Polymer Type: LDPE Molecular Weight: 17,000 Ring and Ball Softening Point: 101°C (ASTM E 28) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 1,800 cP @ 190°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat seal ability Packaging, automotive refinish, wax modification

Epolene® C-16 Polymer

Epolene® C-16 is a maleic anhydride modified, low density polyethylene polymer for use in adhesives, coatings, and color concentrates.

Epolene® C-16 is a branched LDPE homopolymer with maleic anhydrire that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It is well suited for applications requiring compatibility with polyamide. The maleic anhydride modification allows for improved adhesion and improved aging properties in hot melt adhesive formulations. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-16 has a molecular weight of 26,000 and is provided in pellet form. Polymer Type: Ma-PE Molecular Weight: 26,000 Ring and Ball Softening Point: 102°C (ASTM E 28) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: 2,850 cP @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Improved adhesion High filler tolerance Superior aging properties Color concentrates, automotive, wax modification, building & construction coatings, solvent-based adhesives

Epolene® C-16P Polymer

Epolene® C-16P is a maleic anhydride modified, low density polyethylene powder for use in adhesives, coatings, and color concentrates.

Epolene® C-16P is a branched LDPE homopolymer with maleic anhydride that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It is well suited for applications requiring compatibility with polyamide. The maleic anhydride modification allows for improved adhesion and improved aging properties in hot melt adhesive formulations. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-16P has a molecular weight of 26,000 and is provided in powder form. Polymer Type: Ma-PE Molecular Weight: 26,000 Ring and Ball Softening Point: 102°C (ASTM E 28) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: 2,850 cP @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Improved adhesion High filler tolerance Superior aging properties Color concentrates, automotive, wax modification, building & construction coatings, solvent-based adhesives

Epolene® C-17 Polymer

Epolene® C-17 is a low density polyethylene wax with a high melt point and viscosity for use in wax blends, adhesives and color concentrates.

Epolene® C-17 is a branched LDPE homopolymer that can be used as a base polymer in concentrate dispersions and adhesives and to modify paraffin wax blends. It has a relatively high melt point and viscosity compared to other C-type Epolene products. Epolene® C-17 has a molecular weight of 100,000 and is provided in pellet form. Polymer Type: PE Molecular Weight: 100,000 Ring and Ball Softening Point: 133°C (ASTM E 28) Penetration Hardness: 2 dmm (ASTM D5) Viscosity, Brookfield: MI=19 @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Low color Excellent compatibility with tackifying resins automotive, paraffin wax modification, solvent-based adhesives, color concentrates

Epolene® C-17P Polymer

Epolene® C-17P is a low density polyethylene wax powder with a high melt point and viscosity for use in wax blends, adhesives and color concentrates.

Epolene® C-17P is a branched LDPE homopolymer that can be used as a base polymer in concentrate dispersions and adhesives and to modify paraffin wax blends. It has a relatively high melt point and viscosity compared to other C-type Epolene products. Epolene® C-17P has a molecular weight of 100,000 and is provided in powder form. Polymer Type: PE Molecular Weight: 100,000 Ring and Ball Softening Point: 133°C (ASTM E 28) Penetration Hardness: 2 dmm (ASTM D5) Viscosity, Brookfield: MI=19 @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Low color Excellent compatibility with tackifying resins automotive, paraffin wax modification, solvent-based adhesives, color concentrates

Epolene® C-18 Polymer

Epolene® C-18 is a low density polyethylene wax modified with maleic anhydride for use in coatings, adhesives and color concentrates.

Epolene® C-18 is a branched LDPE homopolymer modified with maleic anhydride that can be used as a base polymer in concentrate dispersions, coatings and adhesives. It is well suited for applications requiring polyamide compatibility and offers high gloss and good heat seal ability. Epolene® C-18 has a molecular weight of 15,000 and is provided in pellet form. Polymer Type: PE Molecular Weight: 15,000 Mettle Softening Point: 104°C (ASTM D 6090) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 1,550 cP @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Low color Maleic anhydride grafted automotive, wax coatings, color concentrates

Epolene® C-26 Polymer

Epolene® C-26 is a maleic anhydride grafted polyethylene coupling agent for use in automotive, building and construction and rubber and plastic modification.

Epolene® C-26 is a maleic anhydride grafted polyethylene coupling agent for polyolefin composites. Its molecular weight and polar functionality provide optimal, balanced attraction between polyolefins and fillers, such as wood, glass and metals. Epolene® C-26 has a molecular weight of 65,000 and is supplied in pellet form. Polymer Type: Ma-PE Molecular Weight: 65,000 Mettle Softening Point: 120°C Penetration Hardness: <1 dmm (ASTM D5) Viscosity, Brookfield: MI=8 @ 190°C Maleic anhydride grafted Coupling aid for PE composites Balanced attraction between polar and non-polar components Automotive, rubber and plastic modification

Epolene® E-14E Polymer

Epolene® E-14E is a low-density, low molecular weight oxidized polyethylene pellet for use in adhesives, coatings, plastics and wax blends.

Epolene® E-14E is an oxidized polyethylene wax with low density and low softening point. It produces stable, low color emulsions by both atmospheric and pressure methods. Epolene® E-14E has a molecular weight of 3,600 and is supplied in pellet form. Polymer Type: Ox-PE Molecular Weight: 3,600 Mettle Softening Point: 101°C (ASTM D 6090) Penetration Hardness: 4 dmm (ASTM D5) Good slip resistance High durability & toughness Produces stable emulsions Automotive refinish, Pressure sensitive adhesives, wax modification, floor finishes

Epolene® E-14P Polymer

Epolene® E-14P is a low-density oxidized polyethylene powder for use in adhesives, coatings, plastics and wax blends.

Epolene® E-14P is an oxidized polyethylene wax with low density and low molecular weight. It can be used in color concentrates and as a lubricant in processing rigid and flexible PVC. It is listed with the National Sanitation Foundation (NSF) under Standard 61 Drinking Water System Components Health Effects. Epolene® E-14P has a molecular weight of 4,000 and is supplied in powder form. Polymer Type: Ox-PE Molecular Weight: 4,000 Mettle Softening Point: 104°C (ASTM D 6090) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 375 cP @ 125°C Good slip resistance High durability Produces stable emulsions NSF listed in PVC melt processes Automotive, Automotive OEM, Pressure sensitive adhesives, wax modification, PVC melt processing

Epolene® E-16 Polymer

Low-density oxidized polyethylene having intermediate properties between Epolene® E-14 and Epolene® E-10 with molecular weight of 5,500.

Epolene® E-16 is an oxidized polyethylene wax with low density and low molecular weight. It provides low-color emulsions for use in textiles, polishes, and coatings. Epolene® E-16 has a molecular weight of 5,500 and is supplied in pellet form. Polymer Type: LDPE Molecular Weight: 5,500 Mettler Softening Point: 100°C (ASTM D 6090) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 700 cP @ 125°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat seal ability Produces stable emulsions Automotive refinish, Automotive OEM, Pressure sensitive adhesives, wax modification, floor finishes

Epolene® E-20 Polymer

Epolene® E-20 is a medium-density low molecular weight polyethylene pellet for use in adhesives, coatings, plastics and wax blends.

Epolene® E-20 is an oxidized polyethylene wax with medium density and low molecular weight. It has low color, high hardness and a low softening point. Epolene® E-20 has a molecular weight of 7,500 and is supplied in pellet form. Epolene® E-20 is a great extrusion lubricant for fractional melt HDPE. Polymer Type: Ox-PE Molecular Weight: 7,500 Mettler Softening Point: 111°C (ASTM E 28) Penetration Hardness: <1 dmm (ASTM D5) Viscosity, Brookfield: 1,500 cP @ 125°C High hardness Low color Grease resistance High durability Imparts slip High gloss Improved dispersion High Lubricity Automotive, Pressure sensitive adhesives, wax modification

Epolene® E-25 Polymer

Epolene® E-25 is a maleic anhydride modified polypropylene product used in adhesives, coatings and wax blends and as a coupling agent for filled composites.

Epolene® E-25 is a maleic anhydride modified polypropylene pellet for use in adhesives blends, floor polishes and as a compatibilizer or coupling agent in PP composites. Because of its polarity and anhydride functionality it can be useful in laminating and for enhancing strength of composites that utilize fillers such as glass, talc or metals. Polymer Type: Ma-PP Molecular Weight: 12,000 Ring and Ball Softening Point: 157°C Penetration Hardness: <1 dmm (ASTM D5) Viscosity, Brookfield: 300 cP @ 190°C Excellent pigment dispersion Low color High durability Imparts slip High gloss Book-binding, laminating, caulks and sealants, floor polish finishes

Epolene® E-43 Polymer

Epolene® E-43 is a maleic anhydride grafted polypropylene with a molecular weight of 9,100

Epolene® E-43 is a medium molecular weight, maleic anhydride modified polypropylene pellet for use in adhesives blends, floor polishes and as a compatibilizer or coupling agent in PP composites. Because of its polarity and anhydride functionality it can be useful in laminating and for enhancing strength of composites that utilize fillers such as glass, talc or metals. It also work as processing aid for engineered polymers. Polymer Type: Ma-PP Molecular Weight: 9,100 Ring and Ball Softening Point: 158°C Penetration Hardness: <1 dmm (ASTM D5) Viscosity, Brookfield: 300 cP @ 190°C Excellent pigment dispersion Low color High durability Imparts slip High gloss Book-binding, caulks and sealants, laminating, floor polish finishes

Epolene® E-43P Polymer

Epolene® E-43P is a maleic anhydride modified polypropylene product used in adhesives, coatings and wax blends and as a coupling agent for filled composites.

Epolene® E-43P is a medium molecular weight, maleic anhydride modified polypropylene powder for use in adhesives blends, floor polishes and as a compatibilizer or coupling agent in PP composites. Because of its polarity and anhydride functionality it can be useful in laminating and for enhancing strength of composites that utilize fillers such as glass, talc or metals. Polymer Type: Ma-PP Molecular Weight: 9,100 Ring and Ball Softening Point: 158°C Penetration Hardness: <1 dmm (ASTM D5) Viscosity, Brookfield: 300 cP @ 190°C Excellent pigment dispersion Low color High durability Imparts slip High gloss Book-binding, caulks and sealants, laminating, floor polish finishes

ETHANOX™ 330 Granular

High molecular weight phenolic antioxidant ideal for a wide variety of applications including elastomers, PE wire insulation, hot melt adhesives, tackifiers and engineering polymers. Similar to ETHANOX™ 330 Powder, but in a granular form.

ETHANOX™ 330 exhibits superior performance over typical high molecular weight antioxidants in controlling degradation in polyolefins during processing. It is compatible with a wide variety of resins and most polymer additives. ETHANOX™ 330 is stable at high temperatures, and is electrically neutral, making it a particularly effective antioxidant for PE wire insulation. Appearance: White crystalline powder Melting Point: 244 °C Molecular Weight: 775 g/mol Bulk Density: 630 kg/m³ Broad food-contact approvals Resistant to water and solvent extraction Decreases water carry-over in water-quenched PP films Not absorbed by the fillers commonly used in polyolefins Low volatility Biologically inert Non-staining and non-discoloring Electrically neutral LDPE and HDPE wire insulation, hot melt adhesives

ETHANOX™ 330 Powder

High molecular weight phenolic antioxidant ideal for a wide variety of applications including elastomers, PE wire insulation, hot melt adhesives, tackifiers and engineering polymers. Similar to ETHANOX™ 330 Granular, but in a powder form.

ETHANOX™ 330 exhibits superior performance over typical high molecular weight antioxidants in controlling degradation in polyolefins during processing. It is compatible with a wide variety of resins and most polymer additives. ETHANOX™ 330 is stable at high temperatures, and is electrically neutral, making it a particularly effective antioxidant for PE wire insulation. Appearance: White crystalline powder Melting Point: 244 °C Molecular Weight: 775 g/mol Bulk Density: 630 kg/m³ Broad food-contact approvals Resistant to water and solvent extraction Decreases water carry-over in water-quenched PP films Not absorbed by the fillers commonly used in polyolefins Low volatility Biologically inert Non-staining and non-discoloring Electrically neutral LDPE and HDPE wire insulation, hot melt adhesives

FG

This stearate's grade is a fine grind and fused.

Calcium stearate is a carboxylate which is formed from stearic acid and calcium oxide. Its primary uses are as a flow agent, stabilizer, thicker, and surface conditioner. APPEARANCE: WHITE POWDER FINENESS - THRU 200 MESH %: 95.0-100.0 FREE FATTY ACIDS (AS STEARIC) %: 0.0-0.5 TOTAL ASH %: 11.0-12.0 WATER %: 0.0-3.2 Great for PVC formulations, polypropylenes, and polyolefins.

FireBlend® 25-X

Antimony based flame retardant synergist

FireBlend 25-X is a low cost alternative to antimony trioxide. It acts as an effective synergist in PVC, Polyolefins and ABS when used in combination with a halogen source. Appearance: Fine white powder Antimony content: 25% Average particle size: 1 to 2 microns Specific gravity: 3.48 325 mesh sieve residue: ≤0.20% Low cost Uniform particle size 1:1 replacement for antimony oxide PVC Polyolefins

FireGard LT

Low tint antimony trioxide

FireGard LT is similar to other FireGard grades and is used as synergist in the presence of a halogen source. FireGard LT is particularly effective in low tint applications where color strength and opacity are of importance. The low surface area of FireGard LT is useful in viscosity sensitive applications. Appearance: Fine white powder Specific gravity: 5.5 Average particle size: 2 to 3 microns Sieve residue < 325 mesh: ≤0.10% Antimony Trioxide: 99.8% min Arsenic: 0.10% max Lead: 0.10% max Iron: 0.004% max Low tint Low impurity level Uniform particle size Coatings Adhesives Ceramics Catalyst for PET manufacture Clarifier for glass Opacifier for enamels Coating for titanium dioxide

FireGard® ATO

Flame Retardant/Synergist used in conjunction with brominated or Chlorinated compounds to reduce flammability.

FireGard ATO is Antimony Trioxide that is used as a fire retardant in the presence of a halogen source. In PVC compounds it can be used as the primary FR without the need for a halogen based flame retardant. In other polymers that do not contain halogen, a chlorinated or brominated compound must be added to obtain flame retardancy. Antimony Trioxide (ATO) does not melt or vaporize during normal use and will not form vapors unless heated to extremely high temperatures. FireGard ATO is suitable for applications where a high tint is acceptable. Appearance: Fine white powder Specific gravity: 5.5 Average particle size: 0.8 to 1.3 microns Sieve residue < 325 mesh: ≤0.10% Antimony Trioxide: 99.8% min Arsenic: 0.10% max Lead: 0.10% max Iron: 0.004% max Low cost Low impurities Fine particle size Coatings Adhesives Ceramics Catalyst for PET manufacture Frictional additive in automotive brake linings Clarifier for glass Opacifier for enamels Coating for titanium dioxide

FireGard® HP

High Purity grade of Antimony Trioxide (ATO)

FireGard HP is a high purity grade of Antimony Trioxide that has lower impurities compared to FireGard ATO. FireGard HP has lower levels of Lead & Arsenic compared to FireGard ATO thereby making it the FR of choice for critical applications like ceramic pigment and glass. Appearance: Fine white powder Specific gravity: 5.5 Average particle size: 0.8 to 1.3 microns Sieve residue < 325 mesh: ≤0.10% Antimony Trioxide: 99.8% min Arsenic: 0.05% max Lead: 0.05% max Iron: 0.004% max Low cost Low impurities Fine particle size Coatings Adhesives Ceramics Catalyst for PET manufacture Frictional additive in automotive brake linings Clarifier for glass Opacifier for enamels Coating for titanium dioxide

FireGard® SA

Antimony Synergist

FireGard SA is Sodium Antimonate that is used as a FR synergist in acid sensitive polymers such as PET,PBT, PC and polyamides. FireGard SA is used in applications that need low tint strength thereby maximizing the effect of pigments. FireGard SA also helps produce products that are semi-transparent. Similar to Antimony Trioxide, FireGard SA must be used in conjunction with a halogen. In PVC applications it can be used as the stand alone FR. In other non halogen containing resins, it must be used along with a Bromine or Chlorine FR. Appearance: White powder Antimony content: 61% minimum Trivalent antimony: 0.5% maximum Lead: 0.05% maximum Arsenic: 0.03% maximum Iron: 0.006% maximum Sodium hydroxide: 0.5% maximum 325 mesh: 0.10% maximum Particle size: 2 microns Specific gravity: 4.8 Low reactivity Low opacity Excellent physical properties Low tint strength

FireGard® XF

Submicron particle size Antimony Trioxide (ATO)

FireGard XF is similar to FireGard ATO but with a smaller submicron particle size. The fine particle size of FireGard XF offers minimum loss of properties in thermoplastics like ABS, HIPS, Polyamides and PBT. FireGard XF is also highly effective in liquid systems like polyesters, polyurethanes and phenolics. Appearance: Fine white powder Specific gravity: 5.5 Average particle size: 0.1 to 0.4 microns Sieve residue < 325 mesh: ≤0.10% Extra fine particle size Minimum loss of properties Low level of impurities Coatings Adhesives Glass Ceramics Chemical manufacturing Petroleum refining Electronics

Fluoroguard™ SG Oil

Perfluoropolyether (PFPE) based USP Plastics Class VI Grade compounding additive with excellent color and UV/thermal stability.

Used to internally lubricates parts, offering excellent lubricity while not affecting chemical properties and allowing moving parts to turn easier and last longer. Fluoroguard™ SG Oil is designed for medical grade plastics and elastomers. Average MW: 4950 Volatility: <1% Viscosity (cSt at 50 °C): 107 Density (g/ml at 23 °C): 1.9 Surface Tension (dyn/cm at 26 °C): 18 Refractive Index (nD25): 1.3 Pour Point: -36 °C Appearance: Clear Liquid NAMSA tested for USP Plastics Class VI requirement for polymer additives Improves processing of polymers by internally lubricating plastics and elastomers Colorless Odorless Chemically inert Color, UV, and thermal stability Increases wear resistance Increases flex fatigue resistance Improves product gloss Improves surface lubricity Reduces coefficient of friction Reduces squeak/noise Only used at 0.1-1.0% NSF H1 approved fo incidental food contact

FN Powder

A fused stearate derived from hydrogenated fatty acids. Used as a catalyst neutralizer in polypropylenes.

Calcium stearate is a carboxylate which is formed from stearic acid and calcium oxide. Its primary uses are as a flow agent, stabilizer, thicker, and surface conditioner. Total Ash: 9.30 – 11.50 Fineness, % Thru 325 Mesh: 85.00 – 100.00 Free Fatty Acids: 0.00 – 1.00 Water %: 0.00 – 3.50 Appearance: White Powder Catalyst neutralizer Lubrication in polypropylene's Anti-static agent and acid scavenger in PVC Calcium Stearate FN Powder is a wide variety of applications ranging from waterproofing/ water repelling fabric, stops caking in dehydrated vegetables, as well as a stabilizer in PVC production.

FN VEG, Powder

Vegetable source. This food grade carboxylate is derived from hydrogenated fatty acids and is used as a catalyst neutralizer.

Calcium stearate is a carboxylate which is formed from stearic acid and calcium oxide. Its primary uses are as a flow agent, stabilizer, thicker, and surface conditioner. White powder Insoluble in water Flash point: 176° C Melting point 160° C Insoluble in water Lubricant Mold releasing agent Anti-caking agent FINENESS - THRU 200 MESH %: 99.00 FINENESS - THRU 40 MESH %: 100.00 FREE FATTY ACIDS (AS STEARIC) %: 0.00-2.00 HEAVY METALS %: 0.0-10.0 TOTAL ASH %: 9.00-10.50 USP TEST ARSENIC ppm: 0.0-1.5 WATER %: 0.0-4.00

FP

Calcium stearate is a carboxylate which is formed from stearic acid and calcium oxide. Its primary uses are as a flow agent, stabilizer, thicker, and surface conditioner. White powder Melting point: 160° C Flash point 349° C\ No soluble in water High Heat Stability Low Impurity Reduces Melt Viscosity

GENOX™ EP

High performance, cost-effective melt process stabilizer for polyolefins and other polymers.

GENOX™ EP is a high performance melt process stabilizer for use in polyolefins and other polymer systems. It is very effective even when used without a phenolic antioxidant and provides excellent gas-fading performance. Appearance: Free-flowing white to off-white powder Molecular Weight: 613 g/mol Melting Point: 90 °C Assay: 92% minimum Color (2g / 50 ml isopropyl alcohol solution): 80 APHA max Bulk Density (@20 °C): 0.54-0.56 g/cm³ Cost effective, high performance stabilizer for melt phase Very effective without the assistance of phenolic antioxidants Excellent gas fading performance Raw materials derived from vegetable sources Food contact approval Solid form

Hydroquinone Industrial Photographic

Primary inhibitor, lowest cost, most commonly used general-purpose inhibitor, antioxidant, and intermediate.

Eastman™ Hydroquinone Photographic is an industrial antioxidant that reacts quickly with oxygen. Along with being used as a primary inhibitor, it is also used as an intermediate to manufacture other antioxidants. Appearance: White crystals Flash point: 177°C (350°F) Boiling point: 286°C (547°F) Density @ 4°C: 1.34 g/mL Molecular weight: 110.11 CAS: 123-31-9 Low cost Effective stand-alone oxygen scavenger Reduces corrosion in water treatment applications as a catalyst Does not degrade to ammonia Reacts quickly to oxygen Used as a primary inhibitor to prevent oxidation and industrial applications.

Hystrene® 2290

Hystrene® 2290 is PMC Biogenix's flagship fatty acid and is one of the finest available in the market. It has a vegetable-sourced erucic acid content of approximately 90% and is commercially available as a light brown flake.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number mgKOH/g: 160- 168 Gardner color (1963): 2.0 Iodine Value: 71 - 78 SAP Value: 161 - 169 Titer: 27 - 37 Unsaponifiables: 0 - 2 Water: 0 - 0.25 Melting point: 32 °C / 90 °F Boiling point: >250 °C / >482 °F Flash point: >186 °C / 367 °F Molecular weight: 338.57 Water solubility: insoluble VOC content: 0 Exceptional color stability on light and air exposure Resistant to dilute acids and bases One of the finest available in the market Used for lubricants, cosmetics, waxes, and other chemical intermediates and reactions.

Hystrene® 3022 Flake

Hystrene® 3022 fatty acid has an arachidic/behenic acid content of approximately 30% and is commercially available as a flake. Other major components include palmitic and stearic acids.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 193 - 201 Gardner Color: 0 - 3 Iodine Value g I/100g: 0 - 4 SAP Value mgKOH/g: 194 - 201 Titer: 51 - 55 °C Unsaponifiables: 0 - 1.5 Water: 0 - 0.25 Appearance: white flakes, molten Melting point: 51-55 °C / 124-131 °F Boiling point: >315 °C / >600 °F Flash point: 190 °C / 374 °F Specific gravity: 0.880 g/cm3 Water solubility: insoluble VOC content: 0 Flake form Used for paper coating, plastics, textile auxiliary, cosmetic, and lubricant industries.

Hystrene® 4516 NF FG Kosher

Triple-pressed, high-purity saturated fatty acid. Excellent color and color stability.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 205 - 208 Iodine Value: 0 - 0.5 Titer °C: 55 – 57 Sap Value: 206 - 20 Residue Upon Ignition %: 0 - 0.10 Unsaponifiables %: 0 - 0.20 Water %: 0 - 0.20 45% Palmitic acid Kosher Used for paper coating, plastics, textile auxiliary, cosmetic, and lubricant industries.

Hystrene® 5016 NF EXT, Flake

Triple-pressed stearic acid. External use only.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 206 - 210 Iodine Value: 0 - 4.0 Titer °C: 54.5 – 56.5 Residue on Ignition %: 0 – 0.1 Triple-pressed grade Excellent heat and color stability Used for many polymer additive uses, personal care products including cosmetics and hair care application, food grade products, waxes, printing inks, waxes, pharmaceuticals, paints, plastics, rubber compounding, water repellents and textile auxiliaries.

Hystrene® 5016 NF FG Flake

Hystrene® 5016 NF FG is a triple-pressed stearic acid in flake form.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 206 - 210 Iodine Value: 0 - 4.0 Titer °C: 54.5 – 56.5 Residue on Ignition %: 0 – 0.1 High purity mixture of saturated FG fatty acids of edible sources Approximately 50% palmic acid Triple-pressed grade Excellent heat and color stability Used for many polymer additive uses, personal care products including cosmetics and hair care application, food grade products, waxes, printing inks, waxes, pharmaceuticals, paints, plastics, rubber compounding, water repellents and textile auxiliaries.

Hystrene® 5016 NF FG Powder

Triple-pressed stearic acid. Powder form

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 206 - 210 Iodine Value: 0 - 4.0 Titer °C: 54.5 – 56.5 Residue on Ignition %: 0 – 0.1 Triple-pressed grade Excellent heat and color stability Used for many polymer additive uses, personal care products including cosmetics and hair care application, food grade products, waxes, printing inks, waxes, pharmaceuticals, paints, plastics, rubber compounding, water repellents and textile auxiliaries.

Hystrene® 5016 NF FG Veg - Flake

Hystrene® 5016 NF FG is a triple-pressed stearic acid vegetable in flake form.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 206 - 210 Iodine Value: 0 - 4.0 Titer °C: 54.5 – 56.5 Residue on Ignition %: 0 – 0.1 Triple-pressed grade Excellent heat and color stability Used for many polymer additive uses, personal care products including cosmetics and hair care application, food grade products, waxes, printing inks, waxes, pharmaceuticals, paints, plastics, rubber compounding, water repellents and textile auxiliaries.

Hystrene® 5016 NF FG Veg Powder

Hystrene® 5016 NF FG Veg Powder is a vegetable-based, triple pressed stearic acid in Powder form.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 206 - 210 Iodine Value: 0 - 4.0 Titer °C: 54.5 – 56.5 Residue on Ignition %: 0 – 0.1 Triple-pressed grade Excellent heat and color stability Used for many polymer additive uses, personal care products including cosmetics and hair care application, food grade products, waxes, printing inks, waxes, pharmaceuticals, paints, plastics, rubber compounding, water repellents and textile auxiliaries.

Hystrene® 5522 Flake

Hystrene® 5522 has an arachidic/behenic acid content of approximately 55% and is commercially available as a flake. Other major components include palmitic and stearic acids.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 178 - 185 Gardner Color: 0 - 3 Iodine Value: 0 - 4 Titer: 60 - 63 °C Unsaponifiables: 0 - 1.5 Water: 0 - 0.20 Appearance: white flakes, molten Melting point: 58-65 °C / 135-150 °F Boiling point: >250 °C / >482 °F Flash point: 204 °C / 399 °F Water solubility: insoluble VOC content: 0 Long-chain fatty acid Used for paper coating, plastics, textile auxiliary, cosmetic, and lubricant industries.

Hystrene® 7022 Flake

Hystrene® 7022 has an arachidic/behenic acid content of approximately 70% and is commercially available as a flake.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 170 - 180 Gardner Color (1963): 0 - 3 Iodine Value: 0 - 3 Sap Value: 171 - 181 Titer: 63 - 67 °C Unsaponifiables: 0 - 1.5 Appearance: white flakes, molten Melting point: 63-66 °C / 145-151 °F Boiling point: >315 °C / >600 °F Flash point: 215 °C / 419 °F Water solubility: insoluble VOC content: 0 Superior quality

Hystrene® 9016 Flake

Approximate 90% Palmitic acid

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 217 Titer °C: 61 SAP Value: 219 Iodine Value: 0.3 90% Palmitic acid Adaptable to many applications Used for personal care products including cosmetics and hair care application, waxes, textile auxiliaries, pharmaceuticals, food grade products, emulsifiers and other chemical intermediate and reaction uses.

Hystrene® 9022

Hystrene® 9022 is an exceptionally high-purity, saturated fatty acid with an arachidic/behenic acid content of approximately 90% and is commercially available as a light brown flake.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 171 Titer Deg: 68 °C SAP Value: 173 Gardner Color (1963): 0.8 Iodine Value: 1 Water %: 0.1 Appearance: white to beige flakes, molten Melting point: 67-71 °C / 152-160 °F Boiling point: >315 °C / >600 °F Flash point: 218 °C / 424 °F Water solubility: insoluble VOC content: 0 Light brown color Flake form Used for paper coating, plastics, textile auxiliary, cosmetic, and lubricant industries.

Hystrene® 9718 NF EXT Flake

Hystrene® 9718 NF EXT Flake contains approximately 92% Stearic acid

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 196 - 200 Sap Value: 197 - 201 Titer °C: 66.5 - 69 Residue on Ignition %: 0 – 0.1 92% Stearic acid Used for many polymer additive uses, personal care products including cosmetics and hair care application, food grade products, waxes, printing inks, waxes, pharmaceuticals, paints, plastics, rubber compounding, water repellents and textile auxiliaries.

Hystrene® 9718 NF FG Powder

Hystrene® 9718 NF FG Powder is 92% Stearic Acid.

Hystrene® saturated and unsaturated fatty acids have excellent oxidative and thermal stability which makes them useful in countless sensitive applications. Acid Number: 196 - 200 Sap Value: 197 - 201 Titer °C: 66.5 - 69 Residue on Ignition %: 0 – 0.1 Available in powder, flake, and bulk forms At least 92% Stearic acid Used for chemical intermediate, emulsifier, gelling agent, release agent, anticaking agent foam depressant, resin stabilizer, suspension agent, and pigment depressant.

Impruvol 20

Butylated Hydroxy Toluene is a non-staining, hindered phenolic antioxidant commonly used in a wide variety of applications including plastics, elastomers, petroleum products, and food. Available in several physical forms, including molten.

Sasol's Impruvol 20 is a molten form of Butylated Hydroxy Toluene (BHT), a food grade, low molecular weight, hindered phenolic antioxidant that reduces degradation initiated by heat, light, and time in organic materials. BHT is the most prevalent and approved antioxidant in the world. Appearance: White crystal Specific Gravity @ 60 °F: 1.01 Flash Point (Closed Cup): 245 °F Bulk Density: 37.5 lb/ft³ Purity: 99% minimum Freezing Point: 156.56 °F Color, Molten (APHA): 50 maximum Ash, Residue on Ignition: 0.002% maximum Arsenic: 3 ppm Heavy Metals as Lead: 10 ppm Molecular Weight: 220.34 g/mol Soluble: Methyl alcohol, isopropyl alcohol, ethyl alcohol, benzene, methyl ethyl ketone, petroleum ether, mineral oil, linseed oil, lard Insoluble: Sodium hydroxide, water Food grade Kosher and Halal certified Polyols, polybutylene, hydrocarbon resins, block copolymer elastomers, industrial fats, fatty acids, transmission fluids, lard, shortening, tallow, animal feeds, vegetable oils

Industrene® 106, Liquid

Industrene® 106 is a low-titer oleic acid

Industrene® saturated and unsaturated fatty acids are high-quality fatty acids obtained from animal fat and vegetable oils. Acid Number: 195 - 205 Titer: 0-6 °C Unsaponifiables: 0 - 1 Sap Value: 198 - 205 Gardner Color (1963): 0-3 Iodine Value: 85 - 95 Liquid form Used for alkyd resins, rubber, mineral-flotation, adjuvants, foam depressants, caulking compounds, lubricants, buffing polishes, metallic soaps, abrasives, metal treating compounds, candles, crayons, emulsifiers, etc.

Industrene® 206

Similar to 106 however has a wider color spec

Industrene® saturated and unsaturated fatty acids are high-quality fatty acids obtained from animal fat and vegetable oils. Acid Number: 199 - 204 Gardner Color (1963): 0 - 3 Iodine Value: 85 - 95 Sap Value: 198 - 205 Titer: 0 - 6 Unsaponifiables: 0 - 1 Water: 0 - 0.25 Low titer oleic High-quality Used for alkyd resins, rubber, mineral-flotation, adjuvants, foam depressants, caulking compounds, lubricants, buffing polishes, metallic soaps, abrasives, metal treating compounds, candles, crayons, emulsifiers, etc.

Industrene® 226 - FG Kosher

Industrene® 226 Food Grade distilled soy fatty acid

Industrene® saturated and unsaturated fatty acids are high-quality fatty acids obtained from animal fat and vegetable oils. Acid Number: 195 – 203 Titer: 0–26 °C Gardner Color (1963:) 0 – 3 Unsaponifiables: 0 – 2 Iodine Value: 127 – 138 Water: 0–0.3 Melting point: 25 °C / 77 °F Boiling point: 260 °C / 500 °F Flash point: 174 °C / 345 °F Density: 0.88 g/cm3 @ 25 °C Water solubility: insoluble VOC content: 0 Kosher Used for alkyd resins, rubber, mineral-flotation, adjuvants, foam depressants, caulking compounds, lubricants, buffing polishes, metallic soaps, abrasives, metal treating compounds, candles, crayons, emulsifiers, etc.

Industrene® 4516, Flake

Blend of saturated and unsaturated fatty acids with 45% Palmitic acid

Industrene® saturated and unsaturated fatty acids are high-quality fatty acids obtained from animal fat and vegetable oils. Acid Number: 205 - 208 Iodine Value: 0 - 0.5 Titer °C: 55 – 57 Sap Value: 206 - 209 Residue Upon Ignition %: 0 - 0.10 Unsaponifiables %: 0 - 0.20 Water %: 0 - 0.20 45% Palmitic acid Used for alkyd resins, rubber, mineral-flotation, adjuvants, foam depressants, caulking compounds, lubricants, buffing polishes, metallic soaps, abrasives, metal treating compounds, candles, crayons, emulsifiers, etc.

Industrene® B

Industrene® B is a Stearic Acid in powder form.

Industrene® saturated and unsaturated fatty acids are high-quality fatty acids obtained from animal fat and vegetable oils. Acid Number: 198-207 Gardner Color (1963): 0 - 3 Iodine Value: 0 - 3 Titer: 57 - 63 Stearic acid Available in powder form Used for alkyd resins, rubber, mineral-flotation, adjuvants, foam depressants, caulking compounds, lubricants, buffing polishes, metallic soaps, abrasives, metal treating compounds, candles, crayons, emulsifiers, etc.

Kemamide® B, Bead

Kemamide® B (Bead) is a saturated fatty monoamide formulated from a mixture of behenic acid and arachidic and is most commonly used for its anti-block properties

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 - 4.00 Amide Content: 95.0 - 100.0% Gardner Color: 0.0 - 4.0 Iodine Value: 0.0 - 4.0 Closed Tube Melt Point: 98.0 - 106.0 °C Water Content: 0.00 - 0.25% Appearance: White bead Flash Point (COC): 257 °C Density @ 130 °C: 0.807 g/mL Density @ 160 °C: 0.843 Viscosity @ 130 °C: 6.5 cP Heat of Fusion: 12.7 kcal/mol Fire Point (COC): 284 °C Food contact approved Bead form allows for easy transport Mar-resistant agents, textile softeners and water-repellents,

Kemamide® B, Powder

Kemamide® B (Powder) is a saturated fatty monoamide formulated from a mixture of arahidic and behenic acid and is commonly used for its anti-block properties or as a blending agent

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Amide: 95.0% Min 100.0% Max Iodine Value 0.0 Min 4.0 Max Melt Point 98.0 - 106.0 Powder form Approved for food contact Insoluble in water

Kemamide® E Ultra, Bead

Formulated from unsaturated fatty primary monoamide from vegetable sources and demonstrates excellent color stability

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Amide 98% Gardner Color: 1 Closed Tube Melt Point: 82 °C Water: 0.05% Does not contain Phthalates or BPA Available in bags, drums, and bulk sacks

Kemamide® E Ultra, Pellets

Formulated from unsaturated fatty primary monoamide from vegetable sources and demonstrates excellent color stability

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Amide 98% Gardner Color: 1 Closed Tube Melt Point: 82 °C Water: 0.05% Does not contain Phthalates or BPA Available in bags, drums, and bulk sacks

Kemamide® E Ultra, Powder

Formulated from unsaturated fatty primary monoamide from vegetable sources and demonstrates excellent color stability

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Amide 98% Gardner Color: 1 Closed Tube Melt Point: 82 °C Water: 0.05% Does not contain Phthalates or BPA Available in bags, drums, and bulk sacks

Kemamide® E-180, Powder

Fatty amide used in thermoplastic resins that imparts slip and anti-block characteristics

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 0.60 Total Amine Value: 0.00 – 10.00 Gardner Color (1963): 0.0 – 2.0 Iodine Value: 41.0 – 47.0 Closed Tube Melt Point: 72.0 – 75.0 Water %: 0.00 – 0.25

Kemamide® E-60, Powder

This fatty amide is formulated from vegetable sourced erucic acid and is a unsaturated fatty primary monoamide. Micronized Powder form

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 1.00 Free Fatty Acid: (Oleic) 0.0 – 0.5 Gardner Color (1963): 0.0 – 3.0 Amide: 98.0 – 100.0 Fineness % Thru 40 Mesh: 100.0 min Fineness % On 60 Mesh: 0.0 – 10.0 GLC-C22:1 (Erucic Content): 80.0 – 86.0 Closed Tube Melt Point °C: 76.0 – 86.0 Water: 0.00 – 0.20 Available in bead, molten, and pellet forms as well Excellent choice of additive when needing good slip and anti-block properties Insoluble in water

Kemamide® EBS

This product is a wax that benefits calendering processes, injection and blow molding, and extrusion processing

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Value: 0.0- 7.0 Neutralization Equivalent: 0.0 – 2.0 Total Amine Value: 0.0 – 2.0 Gardner Color (1963): 0.0 – 3.0 Closed Tube Melt Point: 140.0 – 146.0 Water %: 0.00 – 0.20 Free Fatty Acids %: 0.0 – 3.0 % thru 20 Mesh: 99.0 – 100 % on 40 Mesh (Prill only): 0 – 2 Balanced non-polar and polar properties Operates as a high functioning internal and external lubricant

Kemamide® EBS PR

Same as EBS, except in prill form

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Value: 0.0 – 7.0 Neutralization Equivalent: 0.0 – 2.0 Total Amine Value: 0.0 – 2.0 Gardner Color (1963): 0.0 – 3.0 Closed Tube Melt Point: 140.0 – 146.0 Water %: 0.00 – 0.20 Free Fatty Acids %: 0.0 – 3.0 % thru 20 Mesh: 99.0 – 100 % on 40 Mesh (Prill only): 0 – 2 Balanced non-polar and polar properties Operates as a high functioning internal and external lubricant

Kemamide® EZ, Bead

Triple distilled version of Kemamide® E Ultra, also available in pellet and powder form

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Gardner Color: 0.0 – 2.0 Water: 0.00 – 0.25 Closed Tube Melt Point °C: 76.0 – 86.0 Amide: 98.0 – 100.0 FDA approved for use in adhesives, can end cements, paper and paperboard in contact with dry foods, and several other areas

Kemamide® EZ, Pellets

Triple distilled version Kemamide® E Ultra, also available in bead and powder form

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Gardner Color: 0.0 – 2.0 Water: 0.00 – 0.25 Closed Tube Melt Point °C: 76.0 – 86.0 Amide: 98.0 – 100.0 FDA approved for use in adhesives, can end cements, paper and paperboard in contact with dry foods, and several other areas

Kemamide® EZ, Powder

Triple distilled version of Kemamide® E Ultra, also available in bead and pellet form.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Gardner Color: 0.0 – 2.0 Water: 0.00 – 0.25 Closed Tube Melt Point °C: 76.0 – 86.0 Amide: 98.0 – 100.0 FDA approved for use in adhesives, can end cements, paper and paperboard in contact with dry foods, and several other areas

Kemamide® OR, Bead

Oleamide which offers faster blooming in lower temperatures. Also available in powder form.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 1.00 Amide % 98.0: – 100.0 Closed Tube Melt Point °C: 70.0 – 78.0 Gardner Color (1963): 0.0 – 2.0 Iodine Value: 72.0 – 95.0 Water %: 0.00 – 0.20 Effective fast-bloom slip agent and as a mold release lubricant

Kemamide® S, Bead

Formulated from Stearic Acid, this product is a saturated fatty primary monoamide and is most commonly used for its anti-block properties.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 1.00 Amide %: 98.0 – 100.0 Closed Tube Melt Point °C: 98.0 108.0 Gardner Color (1963): 0.0 – 2.0 Iodine Value: 0.0 – 3.0 Water %: 0.00 – 0.25 Exceptional stability to air and light Insoluble in water and most organic solvents

Kemamide® S, Powder

Same as Kemamide® S Bead, in powder form.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 1.00 Amide %: 98.0 – 100.0 Closed Tube Melt Point °C: 98.0 108.0 Gardner Color (1963): 0.0 – 2.0 Iodine Value: 0.0 – 3.0 Water %: 0.00 – 0.25 Exceptional stability to air and light Insoluble in water and most organic solvents

Kemamide® U, Pastilles

Formulated from Oleic Acid, Kemamide® U is an unsaturated fatty monoamide and is commonly used for its slip properties but can also be used for its anti-block properties.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 1.00 Amide %: 97.0 – 100.0 Closed Tube Melt Point °C: 68.0 – 78.0 Gardner Color (1963): 0.0 – 2.0 Iodine Value: 72.0 – 90.0 Water %: 0.00 – 0.20 Low solubility in water Available in multiple forms

Kemamide® U, Powder

Same as Kemamide® U Pastille, in powder form

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 1.00 Amide %: 97.0 – 100.0 Closed Tube Melt Point °C: 68.0 – 78.0 Gardner Color (1963): 0.0 – 2.0 Iodine Value: 72.0 – 90.0 Water %: 0.00 – 0.20 Low solubility in water Available in multiple forms

Kemamide® VO, Bead

Derived from oleic acid from vegetable sources, this product is an unsaturated fatty primary amide

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 1.00 Amide %: 98.0 – 100.0 Closed Tube Melt Point °C: 65.0 – 80.0 Gardner Color (1963): 0.0 – 2.0 Heat Stability 205°C: 0.0 – 4.0 Iodine Value: 80.0 – 99.0 Water %: 0.00 – 0.20 Low solubility in water FDA approved for a variety of applications

Kemamide® VO, Powder

Same as Kemamide® VO Bead, in powder.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Number: 0.00 – 1.00 Amide %: 98.0 – 100.0 Closed Tube Melt Point °C: 65.0 – 80.0 Gardner Color (1963): 0.0 – 2.0 Heat Stability 205°C: 0.0 – 4.0 Iodine Value: 80.0 – 99.0 Water %: 0.00 – 0.20 Low solubility in water FDA approved for a variety of applications

Kemamide® W-20, Pellet

Synthetic wax with a relatively high melting point and excellent slip properties.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Value: 0.0 – 10.0 Closed Tube Melt Point °C: 114.0 – 120.0 Gardner Color (1963): 0.0 – 5.0 Total Amine Value: 0.00 – 10.00 High melting point FDA approved for a variety of applications

Kemamide® W-20, Prill

Synthetic wax with a relatively high melting point and excellent slip properties.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Value: 0.0 – 10.0 Closed Tube Melt Point °C: 114.0 – 120.0 Gardner Color (1963): 0.0 – 5.0 Total Amine Value: 0.00 – 10.00 High melting point FDA approved for a variety of applications

Kemamide® W-40 DF, Prill

This product is a wax that benefits calendering processes, injection and blow molding, and extrusion processing.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Value: 0.0 – 7.0 Total Amine Value: 0.00 – 2.00 Gardner Color (1963): 0.0 – 3.0 Closed Tube Melt Point: 140.0 – 145.0 Water %: 0.00 – 0.20 Compatible with a wide variety of waxes and plasticizers Increases surface's resistance to salt, heat, moisture, and most solvents

Kemamide® W-40 Prill

Formulated from stearic acid, this is used a synthetic wax, as a process lubricant.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Value: 0.0 – 7.0 Total Amine Value: 0.00 – 2.00 Gardner Color (1963): 0.0 – 3.0 Closed Tube Melt Point: 140.0 – 145.0 Water %: 0.00 – 0.20 High melting point Compatible with most plasticizes and waxes Improves surface resistance to moisture, heat, salt, and most solvents

Kemamide® W-40, Powder

Same as Kemamide® W-40 Prill, in powder form.

These fatty amides provide a range of plastic additives, wax additives, and lubricants to various plastics applications. Acid Value: 0.0 – 5.0 Garner Color (1963): 0.0 – 3.0 Closed Tube Melt Point °C: 140.0 – 145.0 Total Amine Value: 0.00 – 5.00 Total Ash: 0.00 – 0.05 Fineness % Thru 100 Mesh: 100.00 (Min) Fineness % Thru 325 Mesh: 99.50 – 100.00 High melting point Compatible with most plasticizes and waxes Improves surface resistance to moisture, heat, salt, and most solvents

Kemester 124, Flake

This product is used in a variety of ways as anti-static agent, lubricant, and emulsifier. Alpha Monoglyceride: 52 - 100% Free Fatty Acid: 0 - 1% Free Glycerine: 0 - 1.5% Gardner Color: 0 - 3 Iodine Value: 0 - 5 g I/100g Bovine sourced

Kemstrene® 99.7% USP

Kemstrene® 99.7% USP is obtained from natural renewable resources and has a purity level of 99.7%.

Kemstrene® is a USP grade glycerine from an FDA validated process which maintains the highest product quality standards, integrity, and safety. Specific Gravity @ 25/25 °C: 1.249 Water %: 5 max Identification (B) - Limit of EG and DEG Diethylene Glycol %: 0.10 max Ethylene Glycol %: 0.10 max FDA approved Naturally derived Used for a wide variety of industrial, personal care, pharmaceutical and food applications.

Larostat® 264 A

Cationic antistat - >= 25.0 - < 50.0% alkyl dimethylethyl ammonium ethosulfate quat.

One of the most widely used cationic antistats in the world is LAROSTAT® 264 A, an alkyl dimethylethyl ammonium ethosulfate quat. A non-halogen quat, it is more effective than other traditional antistats and does not present the problems typical of chloride quats. LAROSTAT® 264 A is usually the antistat of choice for general applications where temperature or FDA requirements are not an issue. It is used for both internal and topical applications. Appearance @ 25°C Clear Amber Liquid Color, Gardner:12 max. Solids, % @ 105°C, 1.5 Hrs: 34.0 – 36.0 pH, 30 % Aqueous: 5.0 – 6.5 Viscosity @ 50°C, cSt: 230 – 330 Compatible with complex chemical systems including many anionic systems. A non-halogen quat, it is more effective than other traditional antistats and does not present the problems typical of chloride quats. It is used for both internal and topical applications. Polyurethane, Polystyrene, Rigid PVC, Fiberglass, Textiles, Dust control, Floor finishes, General purpose

Lithium Stearate 304

Designed to satisfy hydrocarbon and synthetic lubricant-based greases.

The lithium salt of distilled, hydrogenated fatty acids from animals or vegetables. ALKALINITY %: 0.00-0.15 FINENESS - THRU 200 MESH %: 99.00-100.00 FINENESS - THRU 40 MESH %: 100.00-100.01 LITHIUM CONTENT %: 2.40-2.60 WAP24A WATER %: 0.00-2.00 Polymeric coatings Zinc-silicone dioxide coatings Sealing gaskets for food containers Safe in articles that are in contact with food Can be used as a strong binder in certain makeup such as eye shadow, blushes, and other cosmetics. This can also be used as a lubricant in high temperatures.

Lithium Stearate 306

LS #306 is designed for lubricant-based greases, specifically around food processing. Slightly more acidic than #304.

Lithium Stearate is distilled from animal and vegetable sources. Appearance: White powder Melting Point: 212 °C / 414 °F Solubility in Water: Insoluble Molecular Weight: 290.42 g Safe with food processing Meet synthetic lubricant-based grease requirements Can be in paper components touching food Used in various makeup products such as eye shadow, blush, etc. Also good for use in contact with processing food in paper or cardboard.

Lithium Stearate PM

A distilled salt from fatty acids specifically used in grease and great for binding materials together.

Lithium Stearate is the salt distilled from fatty acids of animal or vegetable sources. Appearance: White powder Melting Point: >200 °C Molar Mass: 306.42 g/mol Insoluble in H20 Safe with food processing Meet synthetic lubricant-based grease requirements Can be in paper components touching food Used as a lubricant in industrial applications such as motor vehicles, aircraft, heavy machinery, etc.

LOWILITE™ 20S

Low molecular weight, water soluble benzophenone UV light absorber for use in polymers and water-based cosmetics.

LOWILITE™ 20S provides protection for a variety of materials from degradation caused by exposure to UV light. FDA approvals for food contact and personal care applications means LOWILITE™ 20S can be safely used in water-based cosmetics and sun care products as well as polymers. Appearance: Beige crystalline powder Melting Point: 108-110 °C Molecular Weight: 308 g/mol Acid Number: 182 (mg KOH/g) Bulk Density: 840 kg/m³ Water-soluble Broad food contact approvals FDA approval for personal care applications Used in water-based cosmetics like sunscreen, shampoo, and hair-spray; wool fabrics and dyes; coatings; photographic film and lithographic plates.

LOWILITE™ 22

Low molecular weight benzophenone UV light absorber that offers effective protection for a wide variety of polymers.

LOWILITE™ 22 is a great general purpose, benzophenone UV absorber used in wide variety of polymers, HDPE, LDPE, PP, olefin copolymers (EPR, EPDM, EVA), PVC, polyesters, polystyrene, and ABS rubber. LOWILITE™ 20S provides protection for a variety of materials from degradation caused by exposure to UV light. FDA approvals for food contact and personal care applications means LOWILITE™ 20S can be safely used in water-based cosmetics and sun care products as well as polymers. Appearance: Pale yellow powder Melting Point: 47-50 °C Molecular Weight: 326 g/mol Density: 400 kg/m³ Flash Point: 475 °C Broad food-contact approvals

LOWILITE™ 26

Benzotriazole type UV light absorber, provides strong protection from UV initiated degradation in polyolefins and polyesters.

LOWILITE™ 26 is a strong benzotriazole UV light absorber that prevents yellowing and degradation for a variety of polyolefin and polyester applications. LOWILITE™ 26 provides UV protection in unsaturated polyester coatings cured with cobalt catalysts, without causing discoloration. Appearance: Pale yellow powder Molecular Weight: 316 g/mol Specific Gravity (@25 °C): 1.32 Bulk Density: 260 kg/m³ Melting Point: 137-142 °C Flash Point: 232 °C Broad food-contact approvals Non-discoloring in cobalt cured unsaturated polyester coatings Used in polyolefins, polyesters, and unsaturated polyester coatings cured with a cobalt catalyst.

LOWILITE™ 62

Low melting point HALS that exhibits low interaction with co-additives such as pigments.

LOWILITE™ 62 is a Hindered Amine Light Stabilizer (HALS) with a low melting range. Suitable for use in a variety of polymer systems such as polyolefins, styrenics, unsaturated polyesters, acrylics, PVC, and elastomers. It is ideal for systems containing high additive loadings such as multiple stabilizers and pigments. Appearance: Off-white slightly yellow microgranules Softening Point: 55-77 °C Molecular Weight: 3100-4000 g/mol Bulk Density: 570 kg/m³ Broad food-contact approvals Low interaction with co-additives such as pigments and other stabilizers Used in plastisols, adhesives, sealants and spin-finishes. Great for use in high-pigment load applications.

LOWILITE™ 77

Highly effective hindered amine light stabilizer, suitable for use alone or in combination with oligemeric HALS for thick parts such as car bumpers.

LOWILITE™ 77 is a superior stabilizer compared with UV absorbers and nickel-containing stabilizers. Suitable for use in a variety of polymers including polyolefins, polyamides, polyacetals, and styrenes such as ABS, PS, SAN, ASA, and HIPS. Can be used alone or in combination with oligemeric HALS such as Appearance: Slightly yellow micropellets Melting Point: 80-85 °C Molecular Weight: 481 g/mol Bulk Density: 560 kg/m³ Broad food-contact approvals Works well alone or in combination with oligomeric HALS for use in thick parts such as car bumpers or garden furniture.

LOWILITE™ 92

Liquid form HALS that exhibits low interaction with co-additives such as pigments and other stabilizers.

LOWILITE™ 92 is a ultraviolet light stabilizer suitable for use in polyolefins, styrenics, UPE, acrylics, flexible and rigid PVC, elastomers, adhesives, sealants, coatings, and polyols. Appearance: clear, colorless liquid Melting Point: <4 °C Viscosity (@38 °C): 170 mPa · s Density (@38 °C): 0.979 g/cm³ Liquid form Great for use in liquid applications such as coatings and sealants.

Lowinox™ 22M46

Lowinox™ 22M46 is an antioxidant for synthetic rubbers and latexes. It is also an ideal long-term stabilizer for polyoxymethyle and ABS rubber.

Appearance: White to off-white powder or granules Melting Point: 128-132 °C Molecular Weight: 341 g/mol Bulk Density: 300 kg/m³ (powder), 530 kg/m³ (granular)

Lowinox™ XPS162

Specialty stabilizer blend for extruded polystyrene resins that utilize Emerald Innovation's 3000 flame retardant.

Lowinox™ XPS162 is a stabilizer blend designed to achieve superior stabilization during processing in extruded polystyrene formulations that include Emerald Innovation 3000 flame retardant. Imparts superior melt flow rate and color control across a broad temperature range. Appearance: Yellowish chips Non-dusting Excellent melt flow rate Superior protection from discoloration Synergy with Emerald Innovation's 3000 flame retardant in extruded polystyrene

Microthene® FA 700-00

20 micron high density polyethylene powder with a melt index of 10.

Microthene FA 700-00 is a 20 micron ultra-fine spherical polyethylene powder that is mostly used as an additive in a broad range of specialty applications. Microthene powders offer the properties of polyolefin resins but in a microfine particle size making it suitable for dispersion in aqueous systems. FA 700-00 has the highest peak melting point of all the Microthene grades. Melt index: 10 g/10 min Density: 0.952 g/cc Peak melting point: 134.0°C/273.2°F Low temperature brittleness: -76.0°C/-104.8°F Particle shape: Spherical Average particle size: 20 micron Particle size distribution: 5-50 micron Maximum moisture content: 0.1 % Microfine particle size Uniform particle distribution Spherical shape Long shelf life Easy to disperse Low shrink additive for composites Improve gloss in plastic molded parts Binder in filters and batteries Antitack (pellet dusting) for tacky polymers Viscosity modifier in grease, inks, coatings Carrier/Matrix for fabrics, paper Sintering agent in ceramics

Microthene® FA 709-00

20 micron high density polyethylene powder with a melt index of 10. Flow enhanced version of Microthene FA 700-00.

Microthene FA 709-00 is a 20 micron ultra-fine spherical polyethylene powder that is mostly used as an additive in a broad range of specialty applications. FA 709-00 is a flow enhanced version of FA 700-00. It has small amounts of fumed silica to reduce bridging and clumping. Microthene powders offer the properties of polyolefin resins but in a microfine particle size making it suitable for dispersion in aqueous systems. Melt index: 10 g/10 min Density: 0.952 g/cc Vicat softening point: 125.0°C/257.0°F Peak melting point: 134.0°C/273.2°F Low temperature brittleness: -76.0°C/-104.8°F Tensile strength @ break: 11.7/1,700 Mpa/psi Elongation @ break: 400% Flexural modulus: 1,103/160,000 Mpa/psi Hardness, Shore D: 66 Particle shape: Spherical Average particle size: 20 micron Particle size distribution: 5-50 micron Maximum moisture content: 0.1% Microfine particle size Uniform particle distribution Spherical shape Long shelf life Easy to disperse Flow enhanced version - reduces bridging and powder clumping Low shrink additive for composites Improve gloss in plastic molded parts Binder in filters and batteries Antitack (pellet dusting) for tacky polymers Viscosity modifier in grease, inks, coatings Carrier/Matrix for fabrics, paper Sintering agent in ceramics

Microthene® FE 532-00

20 micron Ethylene Vinyl Acetate (EVA) powder with a melt index of 10.

Microthene FE 532-00 is a 20 micron EVA powder that is mostly used as an additive in a broad range of specialty applications. Microthene powders offer the properties of polyolefin resins but in a microfine particle size making it suitable for dispersion in aqueous systems. Equivalent melt index: 8.0 g/10 min Density: 0.926 g/cc Vicat softening point: 75.0°C/167.0°F Peak melting point: 96.0°C/204.8°F Low temperature brittleness: -76.0°C/-104.8°F Tensile strength @ break: 11.7/1,700 MPa/psi Elongation @ break: 675% Flexural modulus: 93.1/13,500 MPa/psi Hardness, Shore D: 38 Particle shape: Spherical Average particle size: 20 micron Particle size distribution: 5-50 micron Maximum moisture content: 0.1% Microfine particle size Uniform particle distribution Spherical shape Long shelf life Easy to disperse Low shrink additive for composites Improve gloss in plastic molded parts Binder in filters and batteries Antitack (pellet dusting) for tacky polymers Viscosity modifier in grease, inks, coatings Carrier/Matrix for fabrics, paper Sintering agent in ceramics

Microthene® FN 501-00

20 micron low density polyethylene powder with a melt index of 23.

Microthene FN 501-00 is a 20 micron ultra-fine spherical polyethylene powder that is mostly used as an additive in a broad range of specialty applications. Microthene powders offer the properties of polyolefin resins but in a microfine particle size making it suitable for dispersion in aqueous systems. FA 501-00 has the highest melt index of all the Microthene grades. Melt index: 23 g/10 min Density: 0.9245 g/cc Vicat softening point: 92.0°C/197.6°F Peak melting point: 114.5°C/238.1°F Low temperature brittleness: -50.0°C/-58.0°F Tensile strength @ break: 13.1/1,900 MPa/psi Elongation @ break: 120% Flexural modulus: 310.3/45,000 MPa/psi Hardness, Shore D: 54 Particle shape: Spherical Average particle size: 20 micron Particle size distribution: 5-50 micron Maximum moisture content: 0.1% Microfine particle size Uniform particle distribution Spherical shape Long shelf life Easy to disperse Low shrink additive for composites Improve gloss in plastic molded parts Binder in filters and batteries Antitack (pellet dusting) in tacky polymers Viscosity modifier in grease, inks, coatings Carrier/Matrix for fabrics, paper Sintering agent in ceramics

Microthene® FN 510-00

20 micron low density polyethylene powder with a melt index of 5.

Microthene FN 510-00 is a 20 micron ultra-fine spherical polyethylene powder that is mostly used as an additive in a broad range of specialty applications. Microthene powders offer the properties of polyolefin resins but in a microfine particle size making it suitable for dispersion in aqueous systems. Melt index: 4.70 g/10 min Density: 0.923 g/cc Vicat softening point: 97.0°C/206.6°F Peak melting point: 110.0°C/230.0°F Low temperature brittleness: -76.0°C/-104.8°F Tensile strength @ break: 12.4/1,800 MPa/psi Elongation @ break: 550% Flexural modulus: 275.8/40,000 MPa/psi Hardness, Shore D: 53 Particle shape: Spherical Average particle size: 20 micron Particle size distribution: 5-50 micron Maximum moisture content: 0.1% Microfine particle size Uniform particle distribution Spherical shape Long shelf life Easy to disperse Low shrink additive for composites Improve gloss in plastic molded parts Binder in filters and batteries Antitack (pellet dusting) in tacky polymers Viscosity modifier in grease, inks, coatings Carrier/Matrix for fabrics, paper Sintering agent in ceramics

Microthene® FN 519-00

20 micron low density polyethylene powder with a melt index of 5.Flow enhanced version of Microthene FN 510.

Microthene FN 519-00 is a 20 micron ultra-fine spherical polyethylene powder that is mostly used as an additive in a broad range of specialty applications. FN 519-00 is a flow enhanced version of FN 510-00. It has small amounts of fumed silica to reduce bridging and clumping. Microthene powders offer the properties of polyolefin resins but in a microfine particle size making it suitable for dispersion in aqueous systems. Melt index: 4.70 g/10 min Density: 0.9225 g/cc Vicat softening point: 97.0°C/206.6°F Peak melting point: 110.0°C/230.0°F Low temperature brittleness: -76.0°C/-104.8°F Tensile strength @ break: 12.4/1,800 MPa/psi Elongation @ break: 550% Flexural modulus: 275.8/40,000 MPa/psi Hardness, Shore D: 53 Particle shape: Spherical Average particle size: 20 micron Particle size distribution: 5-50 micron Maximum moisture content: 0.1% Microfine particle size Uniform particle distribution Spherical shape Long shelf life Easy to disperse Flow enhanced version - reduces bridging and powder clumping Low shrink additive for composites Improve gloss in plastic molded parts Binder in filters and batteries Antitack (pellet dusting) in tacky polymers Viscosity modifier in grease, inks, coatings Carrier/Matrix for fabrics, paper Sintering agent in ceramics

Microthene® MN 701-00

35 mesh (500 micron) polyethylene powder with a melt index of 70.

Microthene MN 701-00 is a 35 mesh (500 micron) ground low density polyethylene powder that is mostly used as an additive in a broad range of specialty applications. Microthene G powders offer the properties of polyolefin resins but in a ground particle size making it suitable for dispersion in aqueous systems. Melt index: 70 g/10 min Density: 0.912 g/cc Vicat softening point: 75.6°C/168.1°F Peak melting point: 100.8°C/213.4°F Low temperature brittleness: -22.7°C/-8.9°F Tensile strength @ break: 7.7/1,100 MPa/psi Elongation @ break: 400% Flexural modulus: 186/27,000 MPa/psi Hardness, Shore D: 51/44 max/15 seconds Particle shape: Irregular Average particle size: 35 mesh Small ground particle size Long shelf life Easy to disperse FDA approved Automotive parts Color concentrates Structural parts Binder in filters and batteries Carrier/Matrix for fabrics, paper

Microthene® MN 710-20

50 mesh (292 micron) polyethylene powder with a melt index of 22.

Microthene MN 710-00 is a 50 mesh (292 micron) ground low density polyethylene powder that is mostly used as an additive in a broad range of specialty applications. Microthene G powders offer the properties of polyolefin resins but in a ground particle size making it suitable for dispersion in aqueous systems. Melt index: 22 g/10 min Density: 0.915 g/cc Vicat softening point: 81.0°C/177.8°F Peak melting point: 102.7°C/216.9°F Low temperature brittleness: -34.6°C/-30.3°F Tensile strength @ break: 9.3/1,350 MPa/psi Elongation @ break: 610% Flexural modulus: 228/33,000 MPa/psi Hardness, Shore D: 49/43 max/15 sec Particle shape: Irregular Average particle size 50 mesh Small ground particle size Long shelf life Easy to disperse FDA approved Automotive parts Color concentrates Structural parts Binder in filters and batteries Carrier/matrix for fabrics, paper

Microthene® MN 711-20

35 mesh (500 micron) polyethylene powder with a melt index of 22.

Microthene MN 711-00 is a 35 mesh (500 micron) ground low density polyethylene powder that is mostly used as an additive in a broad range of specialty applications. Microthene G powders offer the properties of polyolefin resins but in a ground particle size making it suitable for dispersion in aqueous systems. Melt index: 22 g/10 min Density: 0.915 g/cc Vicat softening point: 81.0°C/177.8°F Peak melting point: 102.7°C/216.9°F Low temperature brittleness: -34.6°C/-30.3°F Tensile strength @ break: 9.3/1,350 MPa/psi Elongation @ break: 610% Flexural modulus: 228/33,000 MPa/psi Hardness, Shore D: 49/43 max/15 sec Particle shape: Irregular Average particle size: 35 mesh Small ground particle size Long shelf life Easy to disperse FDA approved Automotive parts Color concentrates Structural parts Binder in filters and batteries Carrier/matrix for fabrics, paper

Microthene® MN 714-00

50 mesh (292 micron) polyethylene powder with a melt index of 70.

Microthene MN 714-00 is a 50 mesh (292 micron) ground low density polyethylene powder that is mostly used as an additive in a broad range of specialty applications. Microthene G powders offer the properties of polyolefin resins but in a ground particle size making it suitable for dispersion in aqueous systems. Melt index: 70 g/10 min Density: 0.912 g/cc Vicat softening point: 75.6°C/168.1°F Peak melting point: 100.8°C/213.4°F Low temperature brittleness: -22.7°C/-8.9°F Tensile strength @ break: 7.7/1,100 MPa/psi Elongation @ break: 400% Flexural modulus: 186/27,000 MPa/psi Hardness, Shore D: 51/44 max/15 seconds Particle shape: Irregular Average particle size: 50 mesh Small ground particle size Long shelf life Easy to disperse FDA approved Automotive parts Color concentrates Structural parts Binder in filters and batteries Carrier/matrix for fabrics, paper

Microthene® MN 727-00

16 mesh (1190 micron) polyethylene powder with a melt index of 24.

Microthene MN 727-00 is a 16 mesh (1190 micron) ground low density polyethylene powder that is mostly used as an additive in a broad range of specialty applications. Microthene G powders offer the properties of polyolefin resins but in a ground particle size making it suitable for dispersion in aqueous systems. Melt index: 25 g/10 min Density: 0.924 g/cc Vicat softening point: 86.4°C/187.5°F Peak melting point: 109.6°C/229.3°F Low temperature brittleness: -28.3°C/-18.9°F Tensile strength @ break: 8.4/1,220 MPa/psi Elongation @ break: 110% Flexural modulus: 342/49,600 MPa/psi Hardness, Shore D: 56/49 max/15 sec Particle shape: Irregular Average particle size: 16 mesh Small ground particle size Long shelf life Easy to disperse FDA approved Automotive parts Color concentrates Structural parts Binder in filters and batteries Carrier/matrix for fabrics, paper

Microthene® MU 760-00

35 mesh (500 micron) Ethylene Vinyl Acetate (EVA) powder with a melt index of 30.

Microthene MU 760-00 is a 35 mesh (500 micron) ground EVA powder with 18% vinyl acetate that is mostly used as an additive in a broad range of specialty applications. Microthene G powders offer the properties of polyolefin resins but in a ground particle size making it suitable for dispersion in aqueous systems. Equivalent melt index: 32 g/10 min Vinyl acetate content: 18% Density: 0.941 g/cc Vicat softening point: 54°C/129°F Peak melting point: 85°C/185°F Low temperature brittleness: <-76°C/-105°F Tensile strength @ break: 9.4/1,360 MPa/psi Elongation @ break: 760% Hardness, Shore D: 30 Particle shape: Irregular Average particle size: 35 mesh Small ground particle size Long shelf life Easy to disperse FDA approved Automotive parts Color concentrates Structural parts Binder in filters and batteries Carrier/matrix for fabrics, paper

Microthene® MU 763-00

35 mesh (500 micron) Ethylene Vinyl Acetate (EVA) powder with a melt index of 10.

Microthene MU 763-00 is a 35 mesh (500 micron) ground EVA powder with 9% vinyl acetate that is mostly used as an additive in a broad range of specialty applications. Microthene G powders offer the properties of polyolefin resins but in a ground particle size making it suitable for dispersion in aqueous systems. Equivalent melt index: 10 g/10 min Density: 0.927 g/cc Vicat softening point: 72.0°C/161.6°F Peak melting point: 95.1°C/203.2°F Low temperature brittleness: -76.0°C/-104.8°F Tensile strength @ break: 12.0/1,740 MPa/psi Elongation @ break: 760% Flexural modulus: 144/20,800 MPa/psi Hardness, Shore D: 47/42 max/15 sec Particle shape: Irregular Average particle size: 35 mesh Small ground particle size Long shelf life Easy to disperse FDA approved Automotive parts Color concentrates Structural parts Binder in filters and batteries Carrier/matrix for fabrics, paper

NAUGARD™ DLTDP

Thioester based secondary antioxidant that imparts excellent long-term aging in polyolefins and synthetic rubber.

NAUGARD™ DLTDP is a FDA-sanctioned antioxidant in polyolefins and other polymer systems. Used as an auxiliary stabilizer for polyethylene, polypropylene and synthetic rubbers to promote long term heat aging properties. Appearance: White flakes Melting Point: 39-41 °C Molecular Weight: 515 g/mol Odor: Mild Fatty Soluble: Heptane, toluene Slightly Soluble: Alcohol, ethyl acetate Non-dusting Some food contact approvals Synergy with hindered phenolic antioxidants such as ANOX® 20 and ANOX® PP18 to yield: Excellent color Excellent processing stability Excellent long term aging stability

NAUGARD™ DSTDP

Thioester based secondary antioxidant that imparts excellent long-term aging in polyolefins and synthetic rubber.

NAUGARD™ DLTDP is a FDA-sanctioned antioxidant in polyolefins and other polymer systems. Used as an auxiliary stabilizer for polyethylene, polypropylene and synthetic rubbers to promote long term heat aging properties. Appearance: White powder or beads Set Point: 67 °C Molecular Weight: 683 g/mol Odor: Mild fatty Soluble: Heptane, toluene Slightly Soluble: Alcohol, ethyl acetate Non-dusting Some food contact approvals Synergy with hindered phenolic antioxidants such as ANOX® 20 and ANOX® PP18 to yield: Excellent color Excellent processing stability Excellent long term aging stability

NAUGAWHITE™ Liquid

Non-staining, non-discoloring liquid form antioxidant that protects natural and synthetic rubber from degradation due to heat, light, and oxygen exposure.

NAUGAWHITE™ Liquid is a rubber antioxidant that is easily emulsifiable for latex applications and will not stain fabrics, lacquers or other materials through migration or contact. It protects natural and synthetic rubber from degradation due to heat, light, and oxygen exposure. NAUGAWHITE™ Liquid will not yellow when exposed to nitrogen dioxide. Appearance: Clear amber viscous liquid Specific Gravity: 0.96 Soluble: Most organic solvents Insoluble: Water Non-staining Non-discoloring Food contact approvals Does not yellow when exposed to nitrogen dioxide Latex foam, refrigerator gaskets, footwear, proofing, sundries, wire insulation such as SP-1 cord, automotive rubber and cloth backing compounds

NAUGAWHITE™ Powder

Non-staining, non-discoloring powder form antioxidant that protects natural and synthetic rubber from degradation due to heat, light, and oxygen exposure.

NAUGAWHITE™ Powder is a rubber antioxidant suitable for natural and synthetic rubber, that protects against degradation due to heat, light, and oxygen exposure. It will not stain fabrics, lacquers or other materials through migration or contact. NAUGAWHITE™ Powder will not yellow when exposed to nitrogen dioxide. Appearance: Tan powder, 70% active on an inert base carrier Specific Gravity: 1.19 Soluble: Most organic solvents Insoluble: Water Non-staining Non-discoloring Food contact approvals Does not yellow when exposed to nitrogen dioxide Latex foam, refrigerator gaskets, footwear, proofing, sundries, wire insulation such as SP-1 cord, automotive rubber and cloth backing compounds

NB-60, SW

Zinc Stearate NB-60 SW is the zinc salt of distilled hydrogenated fatty acids.

Zinc stearate is a metal salt of a fatty acid. PMC Biogenix offers zinc stearate in both precipitated and fused forms in a wide variety of end use applications. Total ash: 17.00-18.50 Water soluble salts: 0.00-0.50 Water: 0.00-1.00% Fineness thru 325 mesh: 99.80-100.00% Free fatty acids (as stearic): 0.00-2.00 Exceptional resistance to reaction with acid catalysts Soluble in many oils and waxes Can be used for lacquer sanding sealers as a sanding aid to minimize possibilities of "bloom" and "frost" development in subsequently applied top coats of synthetic varnishes containing acid catalysts.

Paraloid EXL™ 2300G

Paraloid EXL™ 2300G is an acrylic core/shell modifier that is ideal for epoxy applications which require high impact strength at temperatures as low as -10°C as well as good heat and UV stability.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: white powder Percent volatility: <1% Bulk density: 0.410-0.530 g/cm3 Glass Trans Temp Mdpt: (-273.15)-(-41) C Exceptional part surface finish Good retention of part rigidity Increase toughness even at thick sections Used to improve UV and heat resistance impact on butyl-acrylate rubber.

Paraloid EXL™ 2314

Paraloid EXL™ 2314 is a highly efficient acrylic toughening agent for engineering resins which has been tailored for various engineering polymers and its blends.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. It is a specialty acrylic modifier that reacts with resin systems for significantly improved toughening, ideal for both weatherable and non-weatherable applications. Foreign Particles: 0-50 Bulk Density g/cm3: 0.380 - 0.580 Moisture: 0 - 1 Retained on 12 MES/1.70 mm: 0 - 1 Pass through 325 mesh/ 0.045mm: 0 - 10 High impact strength High heat stability and weatherability Good retention of part rigidity Excellent processability Excellent part surface finish Increases toughness even at thick sections Well defined rubber particle size Improved capability with polyesters Can be compounded on twin-screw extruders Easy to disperse Can be used for the toughening of low molecular weight PBT, increasing the usefulness of acrylic modifiers to lower temperatures, and in improving the crack propagation behavior of thermosets like epoxy resins.

Paraloid EXL™ 2330

Paraloid EXL™ 2330 is an acrylic core/shell modifier ideal for a wide variety of applications that require high impact strength at temperatures as low as -10°C, as well as good heat and UV stability.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: free-flowing white pwoder Powder bulk density (loose): 0.41-0.57 g/cc Total residue volatiles: ⩽1% Tg: ⩽-43% High impact strength Excellent processability Weatherability Well defined particle size Paraloid EXL™ 2330 modifier can be used where the focus is on weatherability and not low temperature impact strength. Examples include automotive under-the-hood applications, electric and electronic connectors, lawn mowers and tractors' body panels, thermoset molding compounds and adhesives, and to upgrade the impact performance of recycled resins.

Paraloid EXL™ 2335

Paraloid EXL™ 2335 is an acrylic core/shell modifier ideal for a wide variety of engineering resin systems that require good colorability and thermal stability, along with excellent impact performance.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: free-flowing white powder Powder bulk density: 0.41-0.53 g/cc Total residual values: ⩽1% Tg: ⩽-43 °C Better colorability than Paraloid EXL™ 2330 Paraloid EXL™ 2335 modifier can be used for applications where the focus is on weatherability and requirement for deep colored parts. Examples include automotive applications, electric and electronic connectors, body panels for lawn mowers and tractors, and thermoset molding compounds and adhesives.

Paraloid EXL™ 2650J

Paraloid EXL™ 2650J is a general purpose MBS modifier that disperses easily in a variety of engineering resin systems and provides low temperature impact properties.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: white solid Odor: sweet pH: 6-8 Relative density: 0.30-0.50 Water solubility: insoluble Percent volatility: <0% Improves low temperature toughness Based on butadiene rubber Core shell structure Good for when processing conditions / end application conditions are not too extreme.

Paraloid EXL™ 2690

Paraloid EXL™ 2690 is an MBS modifier ideal for polycarbonate/polycarbonate-blend systems that require low temperature performance and ease of processing.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: shite solid Odor: sweet Relative density (air = 1): 0.3-0.5 Water solubility: insoluble Percent volatility: <0.5% Reasonable low T impact / efficiency Excellent performance in polycarbonate Mitigates thickness sensitivity of polycarbonate Only for PC and PC/ABS

Paraloid EXL™ 2691J

Paraloid EXL™ 2691J a free-flowing powder MBS modifier ideal for a wide variety of engineering resins systems that require increased thermal stability and good colorability in both weatherable and non-weatherable systems.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: white solid, opaque Odor: sweet pH: 6-8 Relative density: 0.30-0.50 Water solubility: insoluble Decomposition temperature: >120 °C / >248 °F Percent volatility: <0% Robustness to extreme compounding and molding conditions Robustness to higher temperature / humidity end-use conditions Used to improve the characteristics of many engineering resin systems such as polycarbonate, polyesters, polyamides, polyacetal, and polymer blends.

Paraloid EXL™ 3330

Paraloid EXL™ 3330 is a pelletized MBS modifier that provides heat stability in polycarbonate, polybutylene terephthalate and polyethylene terephthalate systems. It is suitable for both weatherable and non-weatherable applications.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: free-flowing white pwoder Powder bulk density (loose): 0.41-0.57 g/cc Total residue volatiles: ⩽0.70% Tg: ⩽-43% High impact strength Excellent processability Weatherability Well defined particle size Paraloid EXL™ 3330 modifier can be used where the focus is on weatherability and not low temperature impact strength. Examples include automotive under-the-hood applications, electric and electronic connectors, lawn mowers and tractors' body panels, thermoset molding compounds and adhesives, and to upgrade the impact performance of recycled resins.

Paraloid EXL™ 3361

Paraloid EXL™ 3361 is a pelletized acrylic modifier ideal for a wide variety of engineering resins systems that require increased thermal stability and good colorability in both weatherable and non-weatherable applications.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: white pellet Odor: pungent, sweet Melting point/range: 132-149 °C / 269.6-300.2 °F Relative density: 1.13 Water solubility: insoluble Auto-ignition temperature: 400 °C / 752 °F Better thermal stability than Paraloid EXL™ 2330 and Paraloid EXL™ 2335 Better colorability than Paraloid EXL™ 2330 Pellet form Reduces the affect of colorability in dark formulations.

Paraloid EXL™ 3691J

Paraloid EXL™ 3691J is a free-flowing pelletized MBS modifier ideal for a wide variety of engineering resins systems that require increased thermal stability and good colorability in both weatherable and non-weatherable systems.

Paraloid EXL™ Additives increase the ductility of injection moldings, lower temperature toughness, and reduce melt viscosity for engineering resins. Appearance: solid white, opaque Odor: sweet pH: 6-8 Water solubility: insoluble Decomposition temperature: >120 °C / >248 °F Percent volatility: <0.5% Robustness to extreme compounding and molding conditions Robustness to higher temperature / humidity end-use conditions Used to improve the characteristics of many engineering resin systems such as polycarbonate, polyesters, polyamides, polyacetal, and polymer blends.

Paraloid™ BPM-520

Paraloid™ BPM-520 is an acrylic modifier that provides an extraordinary integration of both impact strength and excellent colorability for injection molded opaque packaging and semi-durable applications.

One of the most effective yet FDA-compliant acrylic based impact modifier designed to improve the impact resistance of polylactic acid (PLA). Appearance: free flowing powder Total residual volatiles: 0% Melting point: 132-149 C / 270-300 F Odor: pungent sweet Water solubility: insoluble FDA compliant EU Commission Regulation (No 10/2011) food contact compliant High impact strength at room and sub-zero temperatures Excellent colorability and surface finish for injection molding applications Environmentally and cost efficient Used to improve the impact performance of opaque packaging and semi-durable applications.

Paraloid™ K-120ND

Paraloid™ K-120ND is an acrylic polymer-based, white powder used as an aid in the processing of vinyl compounds. Specifically, K-120ND assists in improving the clarity in vinyl and increasing productions efficiency.

This is a free-flowing acrylic process aid designed to improve the fusion, flow, strength and surface appearance of rigid or flexible vinyl. White, free-flowing powder density(g/cc) 0.40 - 0.46 Specific Gravity at 25C 1.18 Solubility: Methyl ethyl ketone, cyclohexanone, tetrahydrofuran, toluene, and ethylene dichloride Easily mixed into vinyl compounds without the need for supplementary additives like gel Reduced mixing time with better blending for improved processing High melt strength for more controlled parison Improved production output rates and production efficiency Creates a smooth, polished surface K-120ND is ideal when vinyl clarity and consistency is key, specifically with vinyl products manufactured through injection molding, calendering, extrusion, and blow molding.

Paraloid™ K-125

Paraloid™ K-125 is a free-flowing process aid that balances melt strength and viscosity, while improving production efficiency in both rigid and flexible vinyl.

This is a free-flowing acrylic process aid designed to improve the fusion, flow, strength and surface appearance of rigid or flexible vinyl. White free flowing powder Density: 0.43g/cc Specific Gravity: 1.15 Refractoin Index: 1.489 Decreases fusion to sheet and smooth rolling production time High melt strength with low loading levels Improves clarity K-125 can be used to greatly increase vinyl's strength and while overall decreasing the amount of additives needed as well as increasing overall production efficiency. It is used extensively in building materials and construction, vinyl piping, and injection molding.

Paraloid™ K-130D

Paraloid™ K-130D is a processing aid in the production of vinyl that works to boost clarity and improve production performance.

This is a free-flowing acrylic process aid designed to improve the fusion, flow, strength and surface appearance of rigid or flexible vinyl. Acrylic polymer-based compound Free-flowing white powder Density (g/cc) 0.39 -0.49 High clarity in vinyl products Increased efficiency in production Maintains die-swell and viscosity for blow-molding Raises melt strength for better thermoforming

Paraloid™ K-175

Paraloid™ K-175 is a lubricating process aid that offers superior clarity in rigid and flexible vinyl, while decreasing plateout during production.

This is a free-flowing acrylic process aid designed to improve the fusion, flow, strength and surface appearance of rigid or flexible vinyl. White, acrylic based polymer, free-floating white powder Bulk Density 0.51(g/cc) Specific Gravity: 1.05 Completely soluble in Acetone, THF, and Toluene Reduced waste Increased thermal stability Improved output rates High impact strength for injection-molded parts Increased surface tension for print-ability K-175 improves the strength, flexibility and clarity of vinyl. It is used in the manufacturing of bottles, (calendared) film and sheet, as well as packaging applications.

Paraloid™ K-400

Paraloid™ K-400 is an acrylic modifier for PVC foam that increases impact strength, surface appearance and cell uniformity, while also decreasing foam density.

This is a free-flowing acrylic process aid designed to improve the fusion, flow, strength and surface appearance of rigid or flexible vinyl. Acrylic Polymer-based compound Free-floating white powder Bulk Density: 0.40 - 0.52 Lowers foam density Increases impact strength Improves efficiency because less modifier needed Increased flexibility Excellent surface area Faster fusion at lower temperatures K-400 is used most commonly for PVC, which is commonly used during construction. It is commonly used with siding, fences, window frames, roofing, pipes/fittings, injection-molded and foamed parts.

Paraloid™ K-416

Paraloid™ K-416 is used in the production of vinyl to increase density reduction and foam expansion while also maintaining comparable lubricating properties.

This is a free-flowing acrylic process aid designed to improve the fusion, flow, strength and surface appearance of rigid or flexible vinyl. White, free flowing powder Bulk Density(g/cc) 0.32- 0.53 Low use cost Density reduction Strong cell structure at equal loading Increased efficiency at lower levels than K-415 Metal released with no risk of plate-out

Paraloid™ K-445

Paraloid™ K-445 is an acrylic process aid that offers high-efficiency production of cellular vinyl sheet with improved dosage efficiency.

This is a free-flowing acrylic process aid designed to improve the fusion, flow, strength and surface appearance of rigid or flexible vinyl. Acrylic Polymer White, free-flowing powder Bulk Density(g/cc) 0.455 - 0.48 High melt strength Increased Efficiency Lowered density and cost Sheet uniformity Low Density High melt strength and expansion K-445 is mainly used for cellular vinyl products, foam core pipes and foam profile

Paraloid™ KM 330

Paraloid™ KM 330 is an acrylic modifier that combines good impact performance and melt strength with high processing efficiency. It is ideal for exterior vinyl applications

Paraloid™ KM Acrylic Impact Modifiers improves impact efficiency and is excellent as a plastic additive for vinyl. Appearance: free-flowing white powder Odor: pungent, sweet Melting point/range: 132-149 °C / 269.6-300.2 °F Relative density: 1.11 Water solubility: insoluble Auto-ignition temperature: 400 °C / 752 °F High impact strength Outstanding natural weatheribility Control of melt viscoelasticity Neutral color Used for PVC plastics, window frames and profiles, panels, siding, pipes and fittings, injection-molded parts, and additives.

Paraloid™ KM 334

Paraloid™ KM 334 is an acrylic modifier that combines good impact performance and melt strength with high processing efficiency. It is ideal for exterior vinyl applications.

Paraloid™ KM Acrylic Impact Modifiers improves impact efficiency and is excellent as a plastic additive for vinyl. Appearance: free-flowing white powder Odor: pungent, sweet Melting point/range: 132-149 °C / 269.6-300.2 °F Relative density (water = 1): 1.11 Water solubility: insoluble Auto-ignition temperature: 400 °C / 752 °F Proven weatherability Exceeds industry standards as measured by the Gardner test Excellent results even at 0 °C Improves color retention Used for weatherable applications such as siding, window profiles, pipe, and fencing.

Paraloid™ KM 5000

Paraloid™ KM 5000 is a high-efficiency acrylic modifier ideal for improved impact properties in exterior vinyl applications without any additional process aids.

Paraloid™ KM Acrylic Impact Modifiers improves impact efficiency and is excellent as a plastic additive for vinyl. Appearance: white powder Odor: acrylic-like Water solubility: insoluble Percent volatility: <1% Excellent impact resistance 100% acrylic co-polymer Exceptional performance upon lab testing Great for extruded vinyl products such as windows, fence, and deep embossed systems such as in siding substrates.

Paraloid™ KMX 100Pro

Paraloid™ KM 100Pro is a weatherable acrylic modifier that maximizes processing efficiency and delivers the high-gloss finish required in high-volume vinyl profile extrusion.

Paraloid™ KM Acrylic Impact Modifiers improves impact efficiency and is excellent as a plastic additive for vinyl. Appearance: white powder Odor: acrylic-like Percent volatility: <1% Pro provides the best performance profile compared to other industry offerings Excellent impact strength Free flowing 100% acrylic polymer Used for PVC plastics, window frames and profiles, panels, siding, pipes and fittings, injection-molded parts, and additives.

Pationic® 1042K

Pationic® 1042K is a glycerol monostearate (GMS) with 42% alpha-monoester content. It can be used as an internal mold release or for antistatic agent properties. This product is certified Kosher.

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier, and dispersing agent. Free Fatty Acid %: 1 max Free Glycerine %: 1 max Gardner Color: 3 max Iodine Value: 3 max Melting Point °C 60: 64 Monoglyceride %: 42 min FDA Approved

Pationic® 1052K

Pationic® 1052K is a 52% glycerol mono stearate to be used as an additive to polyolefins, styrenics, PVC, TPO and TPE

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier, and dispersing agent. Free Fatty Acid 1% Max Free Glycerine 1.5% Max Iodine Value 3 Max Monoglyceride 52% Min FDA Approved

Pationic® 1052KB

Pationic® 1052KB is a glycerol monostearate (GMS) with 52% monoglyceride content. This grade is offered in bead form. This product is certified Kosher.

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier, and dispersing agent. Capillary Melt Point °C: 60.00 63.00 Free Fatty Acid %: 1 max Free Glycerine %: 1.50 max Gardner Color: 3 max Iodine Value: 3 max Monoglyceride %: 52 min Sieve (10 Mesh Through) %: 99min FDA Approved Kosher Approved

Pationic® 1052P

Pationic® 1052P is a glycerol mono stearate (GMS) with 52% monoglyceride content that is palm oil derived

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier and dispersing agent. Free Fatty Acid 1% Max Free Glycerine 1% Max Iodine Value 3 Max Monoglyceride 52% Min Peroxide Value 1 meq/kg Max FDA Approved

Pationic® 1061

Pationic® 1061 is a 42% glycerol monooleate (GMO) with Mixed Tocopherols and Citric Acid

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti-fogging agent, flow modifier and dispersing agent. Melting Point: 140–145 °F / 60–63 °C Acid Value: 2.00 max Free Fatty Acid %: 1max Free Glycerine %: 1max Gardner Color: 3max Iodine Value: 87 - 114 Moisture %: 0.50 max Monoglyceride %: 42.00 min Peroxide Value meq/kg: 1 max Saponification Value: 170 - 190 FDA Approved Kosher

Pationic® 1240 Kosher

Pationic® 1240 is a lactic acid with 19 - 20% calcium. It can be used as a catalyst residue neutralizer. This product is certified Kosher.

Pationic® products offer diverse solutions for antistats, antifog, lubricants and mold releases. Calcium %: 19 - 20 pH (5% Solution): 11 min Sieve (40 Mesh Through) %: 98 min Calcium lactate-based additive Acid neutralizer

Pationic® 1530

Pationic® 1530 is a specialty glycerol ester containing Propylene Glycol with Propyl Gallate and Citric Acid and formulated to remain a liquid

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier, and dispersing agent. Free Fatty Acid 1% Max Iodine Value 55 Min 70 Max Monoglyceride 46% Min FDA Approved Stable Liquid

Pationic® 901K

Pationic® 901K is glycerol monostearate (GMS) with 95% monoglyceride derived from vegetable oil

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier, and dispersing agent. Free Fatty Acid 1.2% Max Free Glycerine 1.5% Max Iodine Value 3 Max Monoglyceride 95% Min 100% Max FDA Approved Produced to polymer additive heat stability standards

Pationic® 901RF

Pationic® 901RF is a glycerol monostearate (GMS) with 95% monoglyceride derived from hydrogenated vegetable oil and formulated for heat stability Pastille version of Pationic 901K

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier, and dispersing agent. Free Fatty Acid 1.2% Max Free Glycerine 1.5% Max Iodine Value 3 Max Monoglyceride 95% Min Peroxide Value 1 meq/kg Max FDA Approved Pastille form allows for easy handling Kosher Certified

Pationic® 907

Pationic® 907 is a 94.5% unsaturated, distilled monoglyeride and mixed with Asorbic Acid and Tocopherols

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti-fogging agent, flow modifier, and dispersing agent. Free Fatty Acid 1.20% Max Free Glycerine 1.20% Max Iodine Value 80 Min 115 Max Monoglyceride 94.50% Min Peroxide Value meq/kg: 2.00 max FDA Approved Wash off resistant Kosher Certified

Pationic® 909

Pationic® 909 is a glycerol monostearate (GMS) with 99% mono glyceride and 1% triglycerides. It can be used in PP, PE and EPS. This product is certified Kosher.

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier, and dispersing agent. Capillary Melt Point C: 72 - 75 Free Fatty Acid %: 1.20 max Free Glycerine %: 1.50 max Gardner Color: 3 max Iodine Value: 3 max Monoglyceride %: 95 min Sieve (100 Mesh Through) %: 98 - 100 Sieve (200 Mesh Through) %: 90 - 100 Triglyceride %: 1 max

Pationic® 915

Pationic® 915 is a glycerol monostearate (GMS) with 95% monoglyceride

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an anti fogging agent, flow modifier, and dispersing agent. Free Fatty Acid 1.2% Max Free Glycerine 1.5% Max Iodine Value 5 Max Monoglyceride 92% Min FDA Approved Produced to polymer additive heat stability standards Kosher Certified

Pationic® 919

Pationic® 919 is a glycerol tristearate (GTS) with 99-100% triglycerides. It can be used as an external lubricant or mold release. This product is certified Kosher.

Pationic® products offer diverse solutions for antistats, antifog, lubricants and mold releases. Capillary Melt Point °C: 65 - 73 Free Fatty Acid %: 1 max Free Glycerine %: 1 max Gardner Color: 3 max Iodine Value: 3 max Sieve (100 Mesh Through) %: 98 - 100 Triglyceride %: 95 - 100 High purity Narrow particle size Stability Continuous and homogeneous

Pationic® 930

Pationic® 930 is a lactic acid derivative. It can be used as a general purpose acid acceptor. This product is certified Kosher.

Pationic® products offer diverse solutions for antistats, antifog, lubricants and mold releases. Calcium %: 4.20 - 5.20 Gardner Color: 9 max Melting Point °C: 45 - 55 pH: 5 - 7 Sieve (20 Mesh Through) %: 99 min Lubricant and neutralizer

Pationic®1068

Pationic® 1068 is a glycerol mono stearate product with Propyl Gallate and no more than 0.01% Critic Acid (as preservative)

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an antifogging agent, flow modifier and dispersing agent. Free Fatty Acid 1% Max Free Glycerine 1.5% Max Iodine Value 70 Min 80 Max Monoglyceride 52% Min FDA Approved

Pationic®1083

Pationic® 1083 is a glycerol mono oleate product and has a 52% minimum alpha-monoester content

Derived from natural fats and oils, this is often used as internal lubricant in PVC, and can also be used as an antifogging agent, flow modifier and dispersing agent. Free Fatty Acid 1.0% Max Free Glycerine 1.5% Max Iodine Value 70 Min 80 Max Monoglyceride 52% Min FDA Approved Kosher

PhosGard CT

Phosphonate flame retardant for textiles

PhosGard CT is a highly active phosphonate flame retardant with greater than 93% active component and 20% phosphorus. PhosGard CT is especially suited for treatment of textiles. The high phosphorus content makes it suitable for different fabric types especially polyesters. It can also be used in rigid and flexible foam. Appearance: Colorless to Amber liquid Active Component: 93% Phosphorus content: 19% Specific Gravity: 1.20 to 1.30 PH Value: 2.0 to 3.0 Acid Value (mg KOH/g): 20 High active component High Phosphorus content Non Halogen Textiles Fabrics Rigid Foam Flexible Foam

PhosGard RDP

Aryl phosphate ester flame retardant with 11% phosphorus content

PhosGard RDP is a halogen free flame retardant with low volatility and high stability. It is recommended for use in engineered resins, ABS, PC and HIPS. Appearance: Transparent to Pale yellow liquid Phosphorus content: 10.8% Phenol content: ≤ 550 ppm Color: ≤ 80 Acid Value (mg KOH/g): ≤ 0.10 Moisture: ≤ 0.05% Specific gravity: 1.31 to 1.33 Viscosity (25oC mPa·s): 500 to 800 Low volatility High heat stability Liquid Urethane foam

PhosGard® 600

Phosphorus/Nitrogen Intumescent flame retardant.

PhosGard 600 is a non halogenated flame retardant with low solubility for use in engineered resins & thermosets. It is a blend of Phosphorus (21%) and Nitrogen (24%). The nitrogen content helps in char formation and thereby is an effective intumescent. Appearance: White Powder Phosphorus: 19 to 21% Nitrogen: 23 to 24% Moisture: 0.50% max Specific Gravity: 1.4 to 1.6 High purity Low water solubility Good thermal stability Thermosets Coatings Adhesives

PhosGard® 700

Phosphorus/Nitrogen Intumescent flame retardant.

PhosGard 700 is a non halogenated flame retardant for use in polyolefins, TPU and Thermosets. It is a blend of Phosphorus (17%) and Nitrogen (21%). The nitrogen content helps in char formation and thereby is an effective intumescent. Appearance: White powder Phosphorus: 17 to 21% Nitrogen: 21 to 22% Moisture: ≤0.50% Particle size, D50: ≤10 microns Specific gravity: 1.2 High Purity Good thermal stability Non halogenated Thermosets Adhesives Coatings

PhosGard® 7600

Triaryl Isopropylated Phosphate with 7.6% phosphorus content.

PhosGard 7600 functions as a flame retardant and plasticizer for PVC, polyurethanes, synthetic rubber, engineered resins and polycarbonate. PhosGard products are non-halogenated and are available in a liquid form. Appearance: Clear liquid Phosphorus content: 7.6% Color (APHA): ≤50 Viscosity @ 25°C: 95 to 114 cps Acidity (mg KOH/g): ≤0.10 Moisture: ≤0.10% Specific gravity: 1.14 Low viscosity Halogen Free Compatible with a wide variety of resins Coatings Adhesives Sealants Elastomers

PhosGard® 8100

Triaryl Isopropylated Phosphate with 8.1% phosphorus content.

PhosGard 8100 functions as a flame retardant and plasticizer for PVC, polyurethanes, synthetic rubber, engineered resins and polycarbonate. PhosGard products are non-halogenated and are available in a liquid form. Appearance: Clear liquid Phosphorus content: 8.1% Color (APHA): ≤30 Viscosity @ 25°C: 34 to 76 cps Acidity (mg KOH/g): ≤0.10 Moisture: ≤0.10% Specific gravity: 1.16 to 1.18 Low viscosity Halogen Free Compatible with a wide variety of resins Coatings Adhesives Sealants Elastomers

PhosGard® 8300

Triaryl Isopropylated Phosphate with 8.3% phosphorus content.

PhosGard 8300 functions as a flame retardant and plasticizer for PVC, polyurethanes, synthetic rubber, engineered resins and polycarbonate. PhosGard products are non-halogenated and are available in a liquid form. Appearance: Clear liquid Phosphorus content: 8.3% Color (APHA): ≤50 Viscosity @ 25°C: 53 to 64 cps Acidity (mg KOH/g): ≤0.10 Moisture: ≤0.10% Specific gravity: 1.16 to 1.18 Low viscosity Halogen Free Compatible with a wide variety of resins Coatings Adhesives Sealants Elastomers

PhosGard® APP

Ammonium Polyphosphate

PhosGard APP is a fine particle crystal phase II modified Ammonium Polyphosphate with phosphorus content of 31% and Nitrogen content of 15%. PhosGard APP is a low cost flame retardant used to achieve intumescence because the nitrogen present aids in char formation. PhosGard APP is also effective in water based coatings, polyurethanes, thermosets and polyolefins. Appearance: Fine white powder Phosphorus content: 31 to 32% Nitrogen content: 14 to 15% Moisture: ≤0.25% Solubility in water, @ 25°C (g/100 ml): ≤0.5% Decomposition temperature: ≥275°C PH value: 5.5 to 7 Particle size, D50: ≤10 microns Low cost Fine particle size Compatible with a wide variety of resins Helps in Char formation Intumescent Flame Retardants Water based coatings Polyurethanes Thermosets

PhosGard® APP-WS

100% water-soluble Ammonium Polyphosphate.

PhosGard APP-WS is a 100% water soluble version of PhosGard APP used in aqueous systems. APP-WS has phosphorus content of 45% and Nitrogen content of 24%. PhosGard APP-WS is a low cost flame retardant used to achieve intumescence because the nitrogen present aids in char formation. PhosGard APP is especially effective in textile applications. Appearance: Fine white powder P₂O₅ content: ≥ 45% Nitrogen content: ≥ 24% PH value: 6.5 to 8.5 Solubility: Freely soluble in water Low cost Fine particle size Compatible with a wide variety of resins Helps in Char formation Intumescent Flame Retardants Water based coatings Polyurethanes Thermosets

PhosGard® NH4

Butylated phosphate ester flame retardant with 8.1% phosphorus content.

PhosGard® NH4 is a halogen free phosphate flame retardant/plasticizer with low scorch, volatility and fogging suitable for use in flexible urethane foam, PVC and engineered resins. Halogen free phosphate flame retardant/plasticizer Phosphorus content: 8.1% Color (APHA): ≤100 Acid value (mg KOH/g): ≤0.10 Moisture: ≤0.10% Specific gravity: 1.18 to 1.19 Viscosity (25°C, mPa•s): 65 to 75 Low scorch, volatility and fogging, excellent hydrolytic stability. Flexible polyurethane foams, PVC and Engineered resins.

PhosGard® TCP

Tricresyl Phosphate with phosphorus content of 8.4%

PhosGard TCP is a low viscosity phosphorus flame retardant /plasticizer used in PVC, PE and polyurethane coatings and foam. It is recommended for use in synthetic rubber, butylated rubber and chloroprene rubber. Appearance: Clear transparent liquid Phosphorus (theoretical): 8.4% Phenol content: ≤500 ppm Moisture: ≤0.10% Color (APHA): ≤0.10 Viscosity (25°C, mPa.s): 56 to 62 Specific gravity: 1.16 to 1.18 Low viscosity Excellent hydrolytic stability Electric insulation Mildew and abrasion resistance Polyurethane Coatings Polyurethane foam Rubber formulations

PhosGard® TCPP

Chlorinated phosphate ester with 9.5% phosphorus

PhosGard TCPP is a flame retardant with good hydrolytic stability used in rigid and flexible PU foam. It has a low viscosity and high phosphorus content. Appearance: Clear transparent liquid Chlorine (theoretical): 32.5% Phosphorus (theoretical): 9.5% Tri content, %: 50 to 85% Acid value (mg KOH/g): ≤0.07 Moisture: ≤0.07% Color (APHA): ≤50 Viscosity (25°C, mPa.s): 65 to 70 Specific gravity: 1.27 to 1.31 Good hydrolytic stability Low Viscosity High phosphorus content Urethane foam

POLYBOND™ 1001N

Provides improved adhesion of polypropylene to metals and other polar surfaces.

POLYBOND™ 1001N is a polypropylene coupling agent with very high acrylic acid content, which enhances dispersion of fillers and pigments in polypropylene based masterbatches and color concentrates. Helps prevent bloom of polar ingredients. Appearance: Off-white pellet Melt Flow Rate (@ 230 °C): 42 g / 10 minute Acrylic Acid Content: 5.5-6.5% Density (@ 23°C): 0.91 g/cm³ Bulk Density: 0.5 g/cm³ Melting Point: 161°C Improves adhesion of polypropylene to metals and other polar surfaces Improves pigment and filler dispersion in polypropylene masterbatches and color concentrates Some food contact approvals Dispersing aid for fillers and pigments in polypropylene masterbatches and color concentrates Improves adhesion of polypropylene to metals and polar surfaces

POLYBOND™ 1009

Acrylic modified polyethylene additive to improve adhesion of PE to metals and other polar surfaces

POLYBOND™ 1009 can be applied as a coupling agent for glass or mica filled polyethlyene and provides good adhesion to aluminum, stainless steel, tin-plated steel, and a variety of other substances. Appearance: Off-white pellet Melt Flow Rate (@ 190°C): 5.0g/10 min Acrylic Acid Content: 5.5-6.5% Density (@ 23°C): 0.95 g/cm³ Bulk Density: 0.5 g/cm³ Melting Point: 127 °C Low gel count makes this grade ideal for use as a coupling agent and adhesion promoter in sheet and film applications. Improves strength and other physical properties when used as a coupling agent in glass or mineral-filled Polyethylene applications Enhances hydrolytic stability and impact strength when used as a compatibilizer in polythethylene-polyamide blends Some food contact approvals Improves adhesion of polyethylene to metals and other polar surfaces.

POLYBOND™ 3009

Maleic anhydride modified PE coupling agent for glass and mineral filled systems.

POLYBOND™ 3009 is a coupling agent for filled PE systems that provides improved physical properties including strength and impact resistance. It provides good adhesion in film and sheet applications. Appearance: Off-white pellet Melt Flow Rate (@ 190°C): 5.0g/10 minutes Maleic Anhydride Content: 0.8-1.2% Density (@ 23°C): 0.95 g/cm³ Bulk Density: 0.6 g/cm³ Melting Point: 127 °C Low gel count makes this grade ideal for use as a coupling agent and adhesion promoter in sheet and film applications. Improves strength and other physical properties when used as a coupling agent in glass or mineral-filled Polyethylene applications Enhances hydrolytic stability and impact strength when used as a compatibilizer in polythethylene-polyamide blends Some food contact approvals Improves adhesion in sheet and film applications; improves hydrolytic stability in PE/nylon blends; improves impact strength in mineral-filled PE applications; improves strength in glass-filled PE applications

POLYBOND™ 3150

Polypropylene based coupling agent with moderate maleic anhydride content, improves strength and other physical properties and can be used with processing equipment lacking low feed rate capabilities.

POLYBOND™ 3150 is a coupling agent for filled polypropylene systems that provides improved physical properties including flexural/tensile strength and hydrolytic stability. It is ideal for tie-layers between multilayer polar and non-polar materials and compatibalizing PA/PP blends. Appearance: Off-white pellet Melt Flow Rate @ 230 °C: 52 g/10 minutes Maleic Anhydride Content: 0.4 - 0.7% Density @ 23 °C: 0.91 g/cm³ Bulk Density @ 23 °C: 0.5 g/cm³ Melting Point: 157 °C Food contact approvals Moderate maleic anhydride content allows use with equipment lacking low feed rate capability Compatibilizes blends of recycled polyamide and polypropylene Improves flexural strength and reduces water uptake in cellulose fiber filled polypropylene Coupling agent for glass, cellulose fiber and mineral filled polypropylene; improves compatibility between multilayer polar and non-polar materials; compatibilizer for blends of recycled polyamide and polypropylene

POLYBOND™ 3200

Workhorse coupling agent for filled polypropylene and polyamide / polypropylene blends. Can be used with glass, mineral, or cellulose fiber reinforcing materials.

POLYBOND™ 3200 is a high efficiency coupling agent for filled polypropylene systems that improves physical properties such as strength and impact resistance. It provides good adhesion in film and sheet applications and compatibalization of polamide / polypropylene blends. Appearance: Off-white pellets Melt Flow Rate @ 190 °C: 115 g/10 minutes Maleic Anhydride Content: 0.8-1.2% Density @ 23 °C: 0.91 g/cm³ Bulk Density @ 23 °C: 0.6 g/cm³ Melting Point: 157 °C Food contact approvals Great for glass filled, mineral filled, or cellulose fiber filled polypropylene Reduces water uptake Increases flexural and impact strength Compatibilizes polar and non-polar materials Enhances hydrolytic stability in polypropylene / polyamide blends Acts as a coupling agent, process aid, and dispersion aid in halogen free flame retardant compounds for wire and cable Tie layer component between multilayer polar and non-polar materials; wire and cable compounds using halogen-free flame retardants; glass, mineral, or cellulose fiber filled polypropylene; polypropylene / polyamide blends

POLYBOND™ 3349

Coupling agent and compatibilizer for linear low density polyethylene and polyamide blends; excellent for use in composites with high levels of glass or mineral fillers.

POLYBOND™ 3349 is a coupling agent for glass-filled polyethylene composites with high mineral filler levels. It gives enhanced hydrolytic stability and strength when used to compatibalized polyethylene/polyamide blends. It also functions as a process aid for halogen-free flame retardant wire and cable compounds by providing improved dispersion and mechanical properties. Appearance: Off-white pellet Melt Flow Rate (@190 °C): 8.0g / 10 minute Maleic Anhydride Content: 1.0-1.4% Density (@ 23°C): 0.93 g/cm³ Bulk Density: 0.6 g/cm³ Melting Point: 123 °C Improves dispersion of halogen-free flame retardants in wire and cable compounds High maleic anhydride content gives sufficient functionality for use with high mineral filler loading levels Halogen free flame retardant compounds for wire and cable; linear low density polyethylene (LLDPE) / polyamide blends; LLDPE composites with high mineral or glass filler loading

Regular, Powder

Manufactured using the fusion process. The regular grade is often used for general purposes & ceramics.

Calcium stearate is a carboxylate which is formed from stearic acid and calcium oxide. Its primary uses are as a flow agent, stabilizer, thicker, and surface conditioner. Appearance: white powder Melting Point: 160 °C Insoluble in H2O Great tin uses such as thin fibers and films. Does not melt , but will reach plastic phase at a normal processing temperature. Great catalyst/neutralizer.

ROYALTUF™ 372P20

Additive that improves weatherability and impact strength and toughness in styrene-acrylonitrile, polycarbonate, and polyester / polycarbonate blends.

ROYALTUF™ 372P20 is an impact modifier made with a UV and thermally resistance EDPM backbone. Improves weatherability when used in acrylonitrile butadiene styrene. Provides excellent impact resistance in styrene-acrylonitrile even at sub-ambient temperatures. Appearance: Off-white rubbery pellet Continuous Phase: SAN Melt Flow Rate @ 265 °C: 20 g/10 minutes SAN Content: 50% Density @ 23 °C: 0.98 g/cm³ Bulk Density @ 23 °C: 0.55 g/cm³ Food contact approvals Improves weatherability of ABS Excellent impact resistance in SAN at below ambient temperatures Improves toughness and impact strength Weatherable grades of acrylonitrile butadiene styrene

ROYALTUF™ 485

Maleic anhydride modified EPDM, improves impact resistance of polyamides when used in the temperature range of -30 °C to 23 °C.

ROYALTUF™ 485 is a maleic anhydride grafted EPDM impact modifier for polyamides. Imparts "super tough" properties when used at a 20% load rate. As a result of having a semi-crystalline backbone, ROYALTUF™ 485 improves impact resistance when used at temperatures as low as -30 °C. Appearance: Off-white rubber pellet EPDM Backbone: Semi-crystalline elastomer Mooney Viscosity @ 125 °C: 30 Maleic Anhydride Content: 0.4-0.6% Density @ 23 °C: 0.87 g/cm³ Bulk Density @ 23 °C: 0.6 g/cm³ Glass Transition Temperature: -37 °C Can be used at temperatures as low as -30 °C Food contact approvals Gives "super tough" properties when loaded at 20%

ROYALTUF™ 498

ROYALTUF™ 498 a maleic anhydride grafted EPDM used for increasing low-temperature impact resistance of polyamides. It is ideal for recycled polyamide compounds.

ROYALTUF™ 498 is a maleic anhydride grafted EPDM impact modifier for polyamides. Imparts "super tough" properties to nylon when used at a 20% load rate. As a result of having an amorphous backbone, ROYALTUF™ 498 improves impact resistance when used at temperatures as low as -46 °C. Appearance: Off-white rubbery pellet EPDM Backbone: Amorphous elastomer Mooney Viscosity @ 125 °C: 30 Maleic Anhydride Content: 0.8-1.2% Density @ 23 °C: 0.87 g/cm³ Bulk Density @ 23 °C: 0.6 g/cm³ Glass Transition Temperature: -46 °C Food contact approvals Excellent impact resistance in nylon at temperatures as low as -40°C

ROYALTUF™ 527

ROYALTUF™ 527 is a maleic anhydride grafted EPDM impact modifier that is especially useful for improving low-temperature performance polyamides. It is effective in improving physical properties of recycled nylon compounds.

ROYALTUF™ 527 is a maleic anhydride grafted EPDM impact modifier for polyamides. As a result of having an amorphous backbone, ROYALTUF™ 527 improves impact resistance when used at temperatures as low as -47 °C. It imparts "super tough" properties to nylon when used at a 20% load rate. Appearance: Off-white rubbery pellet EPDM Backbone: Amorphous elastomer Mooney Viscosity @ 125 °C: 30 Maleic Anhydride Content: 0.8-1.2% Density @ 23 °C: 0.87 g/cm³ Bulk Density @ 23 °C: 0.6 g/cm³ Glass Transition Temperature: -47 °C Food contact approvals Excellent impact resistance in nylon at temperatures as low as -40°C

SmokeShield® ZB4

Flame Retardant/Smoke Suppressant

SmokeShield ZB4 is primarily used as a smoke suppressant in the presence of a halogen especially in PVC. It can also be used as a synergist instead of ATO in thermoplastic and thermoset applications. Appearance: Fine white powder ZnO content: 36.4 to 38.4% B₂O₃ content: 47.1 to 49.1% Moisture: ≤0.35% Particle size, D50: 4 to 7 microns Compatible with a wide variety of resins Can replace antimony in thermoplastics PVC resin systems Thermosets

T-1 GE

Sodium Stearate is a sodium salt of distilled hydrogenated fatty acids.

Vulcanized promotor, generally used in polymers however specifically seen in room deodorants. Moisture: 3.0% Free fatty acid: 0.2-1.5% Fineness, % thru 100 mesh: 85 Softening point: 205 °C (typical) Soluble in water, methanol, and ethanol High softening point Excellent resistance to hear discoloration Sodium Stearate T-1 is applicable for high impact polystyrene and polypropylene in meeting processing requirements. Can also be used as a dispersant and wetting agent in paper and paperboard processing. In latex paints, it can be sued as a dispersant and emulsifier.

TEP Liquid

Clear, colorless liquid used as a solvent in many applications and carries flame retardant attributes.

Eastman™ TEP (Triethyl Phosphate) is a process solvent that can also be used as a plasticizer for tough, fire-resistant plastics. Commonly used as an intermediate for agricultural chemicals when preparing TEPP (tetraethyl pyrophosphate). Appearance: Clear, colorless liquid Molecular weight: 182.16 Flash point: 99°C (210°F) Boiling point: 209°C (408°F) Specific gravity @ 20°C/20°C: 1.067-1.072 Viscosity @ 20°C: 1.76 cP Viscosity @ 71°C: 0.82 cP CAS: 78-40-0 Effective viscosity reducer in systems filled with aluminum trihydrate (ATH) Enhanced flame resistance in ATH systems Resin intermediates - Used as a viscosity reducer and flame retardant Oil field drilling chemicals - TEP is used in the manufacturing of oil and gas well fracturing agents known as fracturing gels Oil extraction aid - Used as a stimulant for deep wells (most US production) Polyester production - Used in the production of PET, evidently as a catalyst Silicate glass produciton - Used to incorporate phosphorous into silicate glass

Tospearl 120FL

2 micron microfine silicone resin for use as an antiblocking agent in plastic films.

Tospearl 120FL is 2 micron size micro-fine silicone resin that is used as an additive in biaxially oriented polypropylene (BOPP) films as a slip and antiblocking agent. As a slip agent it improves the Coefficient of Friction (COF) to facilitate easier processing, faster line speeds and prevents the film from tearing. Tospearl when used as a antiblocking agent prevents adhesion during film production both on a finished roll or on the inside of the bubble. Appearance: White spherical beads Mean particle diameter (µm): 1.8-2.3 Weight loss @ 250°C and 0.5 hours, %: <1.0 pH²: 6.0-8.0 Bulk specific gravity: 0.35 Particle specific gravity: 1.32 Refractive index: 1.42 Uniform particle size High heat resistance Low surface energy Low refractive index Non migratory Antiblock masterbatch Food packaging Industrial clear films BOPP Films

Tospearl 130FL

3 micron microfine silicone resin for use as an antiblocking agent in plastic films.

Tospearl 130FL is 3 micron size micro-fine silicone resin that is used as an additive in biaxially oriented polypropylene (BOPP) films as a slip and antiblocking agent. As a slip agent it improves the Coefficient of Friction (COF) to facilitate easier processing, faster line speeds and prevents the film from tearing. Tospearl when used as a antiblocking agent prevents adhesion during film production both on a finished roll or on the inside of the bubble. Appearance: White spherical beads Mean particle diameter (µm): 2.3-3.1 Weight loss @ 250°C and 0.5 hours, %: <1.0 pH²: 6.0-8.0 Bulk specific gravity: 0.36 Particle specific gravity: 1.32 Refractive index: 1.42 Uniform particle size High heat resistance Low surface energy Low refractive index Non migratory Antiblock masterbatch Food packaging Industrial clear films BOPP Films

Tospearl 145FL

4.5 micron microfine silicone resin for use as an antiblocking agent in plastic films.

Tospearl 145FL is a 4.5 micron size micro-fine silicone resin that is used as an additive in biaxially oriented polypropylene (BOPP) films as a slip and antiblocking agent. As a slip agent it improves the Coefficient of Friction (COF) to facilitate easier processing, faster line speeds and prevents the film from tearing. Tospearl when used as a antiblocking agent prevents adhesion during film production both on a finished roll or on the inside of the bubble. Appearance: White spherical beads Mean particle diameter (µm): 4.0-5.0 Weight loss @ 250°C and 0.5 hours, %: <1.0 pH²: 6.0-8.0 Bulk specific gravity: 0.43 Particle specific gravity: 1.32 Refractive index: 1.42 Uniform particle size High heat resistance Low surface energy Low refractive index Non migratory Antiblock masterbatch Food packaging Industrial clear films BOPP Films

Tospearl 3120

12 micron microfine silicone resin for use as an antiblocking agent in plastic films, toner additive or in paints and coatings.

Tospearl 3120 is a 12 micron size micro-fine silicone resin that is used as an additive in biaxially oriented polypropylene (BOPP) films as a slip and antiblocking agent. As a slip agent it improves the Coefficient of Friction (COF) to facilitate easier processing, faster line speeds and prevents the film from tearing. Tospearl when used as a antiblocking agent prevents adhesion during film production both on a finished roll or on the inside of the bubble. In Paints & Inks Tospearl is used to improve moisture resistance, control viscosity and clarification of color, tone and gloss control. Average particle size (µm): 12.0 Water content (105°C, 60min): 2% or less pH: 7.5 Specific gravity (25°C): 1.32 Bulk density: 0.46 Specific surface are m²/g: 18 Linseed oil absorption rate ml/100g: 50 Uniform particle size High heat resistance Low surface energy Low refractive index Non migratory Antiblock masterbatch Food packaging Industrial clear films BOPP Films Paints & Coatings Toner

Tospearl TSR 9000

2 micron microfine silicone resin for use as an additive to provide light diffusion.

TSR9000 Spherical Silicone Resin is a 2 micron size micro-fine silicone resin that is used as an additive in plastic resins as a light diffusion aid. The low refractive index of TSR9000 diffuses point line light and gives a matte finish. TSR9000 helps in fabrication of parts that use a light source on the back side of the part. It has good heat stability and can withstand the heat generated during plastic extrusion. Appearance: Spherical white powder Mean particles diameter: 2.0 Weight loss at 250°C for 1 hr, %: 0.2 pH²: 7.0 Bulk specific gravity: 0.32 Particle specific gravity: 1.32 Refractive index: 1.42 Low refractive index High heat stability High crosslink density Low dosage level compared to polycarbonate LED light covers Signboards Flat panel display light diffuser sheets Light diffusion films Light diffusing roof cover units

Twinkling Star ATO

Synergist used in conjunction with brominated or Chlorinated compounds to reduce flammability.

Twinkling Star is a brand of Antimony Trioxide (ATO) that is a white, solid powder used as a fire retardant in conjunction with a halogen to reduce a product's flammability. It functions as a synergist thereby reducing the amount of halogen-based product required to achieve desired levels of flammability. Antimony Trioxide (ATO) does not melt or vaporize during normal use and will not form vapors unless heated to extremely high temperatures. Color: White crystalline powder Assay: 99.5% min (High Tint) Arsenic (As): 0.06% max Iron (Fe): 0.004% max Lead (Pb): 0.08% max Tin (Sn): 0.008% max Mesh: 0.10% max Particle Size: 1.2 to 1.8 microns (cubic crystals) Low cost Low impurities Fine particle size Synergist to provide flame retardancy Catalyst for PET manufacture Frictional additive in automotive brake linings Clarifier for glass Opacifier for enamels Coating for titanium dioxide

ULTRANOX™ 813

ULTRANOX™ 813

W, Powder

General use grade, metal powder lubricant. Most cost effective grade.

The zinc salt distilled from hydrogenated fatty acids. Usually found in paints, lacquers and industrial coatings. Appearance: White powder Melting Point: 120 °C Boiling Point: 160 °C Insoluble in H2O A good lubricant to use in polyethylene and other polymers. Also used as dust-on anti blocks for sticky rubbers or plastics. In adhesives Can be in contact with aqueous and fatty foods when a component of paper Use as lubricant Good for rubber articles

Zinc Stearate 42

Zinc Stearate 42 is the zinc salt of distilled hydrogenated fatty acids.

Zinc stearate is a metal salt of a fatty acid. PMC Biogenix offers zinc stearate in both precipitated and fused forms in a wide variety of end use applications. Total ash: 13.00-15.00 Fineness, % thru 325 mesh: 99.80-100.00 Free fatty acids (as stearic): 0.00-2.00 Water: 0.00-1.00% Water soluble salts: 0.00-0.50 Soluble in many oils and waxes such as turpentine, benzene, toluene, xylene, and vegetable oils Low temperature solubility Zinc Stearate 42 is often used as a lubricant alongside urea and melamine-formaldehyde resins in fiber-reinforced polyesters and copy toners.