HEUCOPHOS® ZPA

HEUCOPHOS® ZPA offers a higher phosphate content than traditional zinc phosphates. Recommended to use in combination with HEUCORIN® RZ.

HEUCOPHOS® products offer wide spectrum anti-corrosives, high-performance polyphosphates, and modified orthophosphates to provide the most optimal anti-corrosion coatings. Zinc as ZnO (%): 38.5 - 40.5 Aluminium as AI (%): 4.0 - 5.5 Phosphorous as PO4 3- (%): 53.0 - 56.0 Loss on ignition 600°C (%): 9.0 - 12.5 Water-soluble chloride (%): max. 0.025 Water-soluble sulphate (%): max. 0.05 Conductivity (µS/cm): max. 300 pH: 5.5 - 6.5 Lead as Pb (ppm): max. 10 Cadmium as Cd (ppm): max. 10 Density (g/cm3): typ. 2.8 Bulk density, untamped (g/cm3): typ. 0.3 Bulk density, tamped (g/cm3): typ. 0.6 Oil absorption value (g/cm3): typ. 40 Sieve residue 32 microns (%): max. 0.01 Average particle size (microns): 2.0 - 3.5" Improved phosphate loading Excellent for long oil alkyds Excellent for polyurethanes

2-Ethylhexyl Acrylate

2-Ethylhexyl Acrylate (2-EHA) is insoluble in water but also less dense than water. It has a sweet pleasant odor, is clear and color less.

Building blocks for polymer manufacturing and as a feedstock for chemical synthesis. Appearance: clear and colorless Physical Form: liquid Odor: sweet Molar Mass: 184.3 Assay (Gas chromatography) - min 99.6% Water Content (ASTM E 203) - max. 0.05% Acid Content (ASTM D 1613) - max. 0.009% Color on despatch (ASTM D 1209) - max. 10 Standard Stabilization (ASTM D 3125) 15+/- 5ppm MEHQ Readily undergoes addition reactions

30

The aluminum salt of distilled, hydrogenated fatty acids.

This product has strong lubrication characteristics, thickening ability, thermal stability, and water-repellent characteristics. Appearance: white powder Melting Point: 160 °C Insoluble in H2O Great for protective and decorative coating preservation. Great for thickening of aromatic solvents in inks.

AAA (Acetoacetanilide)

White powder that is used in conjunction with styrenated resins to form pigments and agricultural chemicals.

Eastman™ AAA is often used as an intermediate to manufacture pigments, dyes, and fungicides. When used as a copromoter can be blended with DMAA at a 70/30 (DMAA/AAA) ratio resulting in superior performance compared to DMA in equal concentrations in resins utilizing neopentyl glycol. Appearance: White to off-white powder Assay: 99.8% Specific gravity @ 20°C/20°C: 1.26 Flash point open cup: 167°C (332°F) Flash point closed cup: 150°C (302°F) Fire point: 178°C (352°F) CAS: 102-01-2 Low color and toxicity as a copromoter Accelerates reactions in polyester resins and pigment manufacturing Good performance in producing yellow pigments Used as an intermediate for pigments, dyes, paints, graphic arts and agricultural chemicals. AAA is also used as a co-promoter for unsaturated polyesters.

AAEM (Acetoacetoxy Ethyl Methacrylate)

Low solution viscosity with excellent solubility, adjust final pH to 6-7 to improve stability.

Eastman™ AAEM is a methacrylic monomer used in high-solid acrylic resins and acrylic emulsion formulations resulting in lower VOC emissions. This product is commonly used to react with amines and hydrazides to make monomers for self-crosslinkable, room temperature cure acrylic emulsions. Appearance: Clear, light yellow liquid Viscosity @ 25°C: 6.9 cP Flash point: 134°C (273°F) Specific gravity @ 25°C/25°C: 1.12 AAEM: 95.0 wt % min HEMA: 4.0 wt % max Methacrylic acid: 0.5 wt % max CAS: 21282-97-3 Excellent flexibility and corrosion resistance Reduces viscosity in resins for lower VOC emissions Improves adhesion to metal substrates Used in applications such as automotive oems, polymers and plastics.

AQUIS™ BW 3521

AQUIS™ BW 3521 is a phthalo blue liquid dispersion.

Aquis™ colorants are heavily pigmented dispersions used for decorative coatings and specialized water based applications Appearance: Blue Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10) : 10.3 Fineness of Grind (µm): 7.0 Wt. Pigment (%): 48.9 Wt. Solid (%): 57.0 Vol. Pigment (%): 37.8 Vol. Solid (%): 46.1 " Nonionic and anionic wetting and dispersing agents In-plant tinting for waterborne paints Free of binders and solvents"

AQUIS™ PLUS BWP 1500

AQUIS™ Plus BWP 1500 is a phthalo blue liquid dispersion.

Aquis™ Plus colorants are specifically engineered pigment to surfactant ratio. They are often suited for in-plant coatings. Appearance: Blue Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10) : 9.5 Fineness of Grind (µm): 7.0 Wt. Pigment (%): 34.0 Wt. Solid (%): 38.0 Vol. Pigment (%): 25.0 Vol. Solid (%): 29.4" Water-based mono pigment Broad range of compatibility Variety of aqueous applications"

AQUIS™ PLUS RWP 2540

AQUIS™ Plus RWP 2540 is a red liquid dispersion.

Aquis™ Plus colorants are specifically engineered pigment to surfactant ratio. They are often suited for in-plant coatings. Appearance: Blue Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10) : 9.5 Fineness of Grind (µm): 7.0 Wt. Pigment (%): 34.0 Wt. Solid (%): 38.0 Vol. Pigment (%): 25.0 Vol. Solid (%): 29.4" Water-based mono pigment Broad range of compatibility Variety of aqueous applications"

AQUIS™ RW 3170

AQUIS™ RW 3170 is a calcium red liquid dispersion.

Aquis™ colorants are heavily pigmented dispersions used for decorative coatings and specialized water based applications Appearance: Red Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10) : 9.4 Fineness of Grind (µm): 7.0 Wt. Pigment (%): 31.0 Wt. Solid (%): 35.0 Vol. Pigment (%): 21.8 Vol. Solid (%): 26.6" Nonionic and anionic wetting and dispersing agents In-plant tinting for waterborne paints Free of binders and solvents"

BIOBAN™ 200

This dichloro-octylisothiazolinone (DCOIT) based thin-film fungicide and mildewcide suitable for aqueous based products.

DuPont antimicrobials are a collection of in-can and thin film preservatives that are appropriate for a multitude of product applications. Physical state: Flowable dispersion Color: Blue pH: 7 Flash point: >100°C (212 °F) Low leaching Non-yellowing Cost-effective Stains preservative, solvent based preservative, coating preservative, adhesive preservative, caulks, sealants, stucco, grout

Butyl Acrylate

Butyl acrylate (BA) is an acrylic acid ester with a sharp pungent odor. It is somewhat less dense than water and forms a slick surface on water.

Building blocks for polymer manufacturing and chemical manufacturing. Appearance: clear and colorless Physical Form: liquid Odor: pungent Molar Mass: 128.2 Assay (Gas chromatography) - min 99.5% Water Content (ASTM E 203) - max. 0.05% Acid Content (ASTM D 1613) - max. 0.01% Color on despatch (ASTM D 1209) - max. 10 Standard Stabilization (ASTM D 3125) 15+/- 5ppm MEHQ Forms copolymers and homopolymers Useful for feedstock synthesis Very slightly soluble in water

CA-394-60LF

CA-394-60LF is a low odor cellulose acetate with a very high melting point.

CA-394-60LF provides high strength and good resistance to UV light, hear, oils, and greases in various lacquers. It can be used in lacquers for glass, plastic, wire, and release coatings. ASTM-A viscosity, sec: 24 - 44 Acetyl by titration, wt%: 40.0 +/- 0.5 Moisture, wt%: 5.0 (max) Chemical resistant Provides high strength Good weather-ability Non-yellowing Good flow and leveling Pigment dispersion medium Provides metallic pigment control Redissolve resistance Intercoat adhesion

CA-398-10

CA-398-10 is a medium viscosity cellulose acetate. It gives high strength and excellent chemical resistance in coatings and adhesives.

CA-398-10 offers excellent chemical resistant, a high glass transition temperatures and produce tough and hard films. Cellulose acetates are soluble in strong solvents like acetone, methyl ethyl ketone, and ethyl acetate. They are compatible with plasticizers such as dimethyl phthalate or triacetin. The melting point and harness are relatively high. In membranes cellulose acetates (CA) provide strong, clear, chlorine resistant films. ASTM-A viscosity, sec: 8.0 - 13.0 Acetyl by titration, wt%: 39.8 +/- 0.5 Moisture, wt%: 3.0 (max) Chemical resistant Provides high strength Good weather-ability Non-yellowing Good flow and leveling Pigment dispersion medium Provides metallic pigment control Redissolve resistance Intercoat adhesion Membrane material

CA-398-3

CA-398-3 is the lowest viscosity grade of the cellulose acetate range. It is used as additive in protective coatings for electronics, adhesives and plastic products.

CA-398-3 provides performance benefits in solvent- and grease-resistant coatings for textile, wire and paper products, barrier and release coatings for adhesives, protective coatings for plastic items and membrane material. Cellulose acetates are only soluble in strong solvents like acetone, methyl ethyl ketone, and ethyl acetate. They are compatible with plasticizers such as dimethyl phthalate or triacetin. The melting point and harness are relatively high. In membranes cellulose acetates (CA) provide strong, clear, chlorine resistant films. ASTM-A viscosity, sec: 2.0 - 4.0 Acetyl by titration, wt%: 39.8 +/- 0.5 Moisture, wt%: 3.0 (max) Chemical resistant Provides high strength Good weather-ability Non-yellowing Good flow and leveling Pigment dispersion medium Provides metallic pigment control Redissolve resistance Intercoat adhesion Membrane material

CA-398-30

CA-398-30 is the highest viscosity grade in the cellulose acetate range. It provides valuable properties in protective coatings.

CA-398-13 offers excellent chemical resistant, a high glass transition temperatures and produce tough and hard films. Cellulose acetates are soluble in strong solvents like acetone, methyl ethyl ketone, and ethyl acetate. They are compatible with plasticizers such as dimethyl phthalate or triacetin. The melting point and harness are relatively high. In membranes cellulose acetates (CA) provide strong, clear, chlorine resistant films. In membranes cellulose acetates (CA) provide strong, clear, chlorine resistant films. ASTM-A viscosity, sec: 8.0 - 13.0 Acetyl by titration, wt%: 39.8 +/- 0.5 Moisture, wt%: 3.0 (max) Chemical resistant Provides high strength Good weather-ability Non-yellowing Good flow and leveling Pigment dispersion medium Provides metallic pigment control Redissolve resistance Intercoat adhesion Membrane material

CA-398-6

CA-398-6 is a low viscosity cellulose acetate. It can be used as a performance additive in tapes and sealants.

CA-398-6 offers excellent chemical resistant, a high glass transition temperatures and produce tough and hard films. Cellulose acetates are soluble in strong solvents like acetone, methyl ethyl ketone, and ethyl acetate. They are compatible with plasticizers such as dimethyl phthalate or triacetin. The melting point and harness are relatively high. In membranes cellulose acetates (CA) provide strong, clear, chlorine resistant films. ASTM-A viscosity, sec: 5.0 - 7.0 Acetyl by titration, wt%: 39.8 +/- 0.5 Moisture, wt%: 3.0 (max) Chemical resistant Provides high strength Good weather-ability Non-yellowing Good flow and leveling Pigment dispersion medium Provides metallic pigment control Redissolve resistance Intercoat adhesion Membrane material

CAB-171-15

CAB-171-15 has the lowest butyryl content grade in the CAB range, offering superior hardness and toughness.

CAB-171-15 is a cellulose ester resin with a low butyryl content and high viscosity content. It is one of the toughest CABs. It is recommended for thermoplastic lacquers with a good resistance to chemicals, solvents or heat are required, such as wire coatings, textile coatings, and printable films. This grade has limitations in compatibility though. Viscosity ASTM-A, sec: 14 - 24 Acetyl by GC, wt%: 28 - 31 Butyryl by GC, wt%: 16.5 - 19 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 0.8 - 1.4 Film toughness Heat resistance Improves flow and leveling Reduces cratering Reduces dry time Provides polishability Improves sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

CAB-321-0.1

CAB-321-0.1 is a cellulose ester resin with a low butyryl content. The low viscosity permits higher solids concentrations.

CAB-321-0.1 is a cellulose ester resin with a low butyryl content low high viscosity content. Cellulose esters provide excellent color and color retention, film toughness, flexible films, flow control and anti-corrosion. Main applications are in curing inks and coatings for metal, wood, textiles, cloth, paper, plastic, and leather. Viscosity ASTM-A, sec: 14 - 24 Acetyl by GC, wt%: 28 - 31 Butyryl by GC, wt%: 16.5 - 19 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 0.8 - 1.4 Film toughness Heat resistance Improves flow and leveling Reduces cratering Reduces dry time Provides polishability Improves sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

CAB-381-0.1

CAB-381-0.1 is a cellulose ester resin with a medium butyryl content and has the lowest molecular weight of the 381 range. This product is designed for use in curing coatings and inks.

CAB-381-0.1 is with its medium butyryl content soluble and compatible with many resins and plastizers. It provides excellent color and color retention, film toughness, flexible films, flow control and anti-corrosion. Main applications are in curing inks and coatings for metal, wood, textiles, cloth, paper, plastic, and leather. Viscosity ASTM-A, sec: 0.07 - 0.16 Acetyl by GC, wt%: 12 - 15 Butyryl by GC, wt%: 36 - 40 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 1.0 - 2.0 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

CAB-381-0.5

CAB-381-0.5 is a cellulose ester with low viscosity and medium butyryl content. It is designed for relatively high solid applications.

CAB-381-0.5 is a general purpose cellulose ester and recommended for many types of coatings and inks. It provides excellent color, flexibility, flow control, pigment dispersion and weather resistance. 381 is compatible with many resins and is soluble in low-cost solvent systems. This low viscosity 381 provides wetting and adhesion improvement in inks. In coatings improved metal flake orientation, resistance to redissolve from the topcoat solvents and excellent sprayability are key benefits. CAB-381-0.5 is commonly used in nail coatings for its compatibility, it improves dry-time and flexibility of nail clearcoats. Viscosity ASTM-A, sec: 0.33 - 0.55 Acetyl by GC, wt%: 12 - 15 Butyryl by GC, wt%: 36 - 40 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 1.0 - 2.0 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

CAB-381-2

CAB-381-2 is a resin with a high viscosity. It is effective in increasing cold-crack resistance and results in greater film toughness.

CAB-381-2 is a cellulose ester resin with medium butyryl content and high viscosity level. It improves dimensional stability, better toughness, and mechanical characteristics. It can be used as a film former, as an additive to other film formers, and as a reactive polyol in curing coatings. Viscosity ASTM-A, sec: 1.2 - 2.8 Acetyl by GC, wt%: 12 - 15 Butyryl by GC, wt%: 36 - 40 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 1.0 - 2.0 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

CAB-381-2 BP

CAB-381-2 BP is similar to CAB-381-2 designed to meet the needs of European formulators.

CAB-381-2 BP is a cellulose ester resin with medium butyryl content and high viscosity level. It improves dimensional stability, better toughness, and mechanical characteristics. It can be used as a film former, as an additive to other film formers, and as a reactive polyol in curing coatings. Viscosity ASTM-A, sec: 0.33 - 0.55 Acetyl by GC, wt%: 12 - 15 Butyryl by GC, wt%: 36 - 40 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 1.0 - 2.0 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion Compliant with European standards

CAB-381-20

CAB-381-20 has the highest viscosity in its range and can be used as both binder and thickener in coatings and inks.

CAB-381-20 is a cellulose ester resins with medium butyryl content and high viscosity. It provides excellent color, greater toughness, better mechanical properties and high cold crack resistance due to improved dimensional stability. CAB-381 products are compatible with many resins and soluble in low-cost solvent systems. Viscosity ASTM-A, sec: 17 - 28 Acetyl by GC, wt%: 12 - 15 Butyryl by GC, wt%: 35 - 39 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 1.4 - 2.2 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

CAB-381-20 BP

CAB-381-20 BP is a slightly modified version of CAB-381-20 designed to meet the needs of European formulators.

CAB-381-20 BP is a cellulose ester resins with medium butyryl content and high viscosity. It provides greater toughness, better mechanical properties and high cold crack resistance due to improved dimensional stability. CAB-381 products are compatible with many resins and soluble in low-cost solvent systems. Viscosity ASTM-A, sec: 12 -20 Acetyl by GC, wt%: 14 - 17 Butyryl by GC, wt%: 33.0 -38.0 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 0.5 - 1.2 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion Compliant with European standards

CAB-500-5

CAB-500-5 has a high butyryl and low hydroxyl content and medium viscosity. It results in flexible films requiring limited amount of plasticizers.

CAB-500-5 is a cellulose acetate butyrate and used as binder or additive in coatings and inks. With a high butyryl level, CAB-500-5 contributes to high flexibility, high solubility and compatibility with cross-linking resins and plasticizers. It is used in finishes to improve dry-to-touch time, reduce cratering, provide better pigment dispersion and improve coating performance. It has tolerance for nonpolar aliphatic and aromatic hydrocarbons. Viscosity ASTM-A, sec: 3 - 6 Acetyl by GC, wt%: 2.5 -5 Butyryl by GC, wt%: 49 - 53 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 0.8 - 1.2 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

CAB-531-1

CAB-531-1 is a high butyryl cellulose ester resin. It provides tough films with good marring resistance.

CAB-531-0.1 is used as binder or additive in coatings and inks. The high butyryl level provides high flexibility, high solubility, good adhesion and compatibility with cross-linking resins and plasticizers. It is used in finishes to improve dry-to-touch time, reduce cratering, provide better pigment dispersion and improve coating performance. Viscosity ASTM-A, sec: 1.3 - 2.6 Acetyl by GC, wt%: 2 - 4 Butyryl by GC, wt%: 48 - 52 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 1.1 - 2.1 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

CAB-551-0.01

CAB-551-0.01 is the lowest viscosity cellulose ester resin with the highest butyryl substitution.

CAB-551-0.01 is used as binder or additive in coatings and inks. The high butyryl level contributes to high flexibility, high solubility and compatibility with cross-linking resins and plasticizers. Due to its low molecular weight, 551-0.01 provides better flow and wetting. It is used in cross-linked finishes to improve dry-to-touch time, reduce cratering, provide better pigment dispersion and improve coating performance. It is soluble in monomers, like styrene. CAB-551-0.01 can be used by pultruders to enable higher pultrusion speed and prevent internal/external cracking. Viscosity ASTM-A, sec: 0.01 Acetyl by GC, wt%: 4 Max Butyryl by GC, wt%: 50-54 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 1.6 - 2.4 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion Improve pultrusion speed Prevent pultrusion cracking

CAB-551-0.2

CAB-551-0.2 is a high butyryl, and relatively low molecular weight resin. It is compatible with numerous cross-linking resins.

CAB-551-0.2 is cellulose ester used as binder or additive in coatings and inks. With the high butyryl level, CAB-551 contributes to high flexibility, high solubility and compatibility with cross-linking resins and plasticizers. It is widely used in cross-linked finishes to improve dry-to-touch time, reduce cratering, provide better pigment dispersion and improve coating performance. It is soluble in monomers, like styrene. CAB-551-0.2 can be used by pultruders to enable higher pultrusion speed and prevent internal/external cracking. Viscosity ASTM-A, sec: 0.16 - 0.25 Acetyl by GC, wt%: 4 Max Butyryl by GC, wt%: 49.0 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 1.4 - 2.4 Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion Improve pultrusion speed Prevent pultrusion cracking Soluble in alcohol

CAB-553-0.4

CAB-553-0.4 is a high butyryl, high hydroxyl cellulose ester resin. It is soluble in alcohols.

CAB-553-0.4 is used as binder or additive in various types of coatings and inks. The high butyryl level provides high flexibility, high solubility and compatibility with cross-linking resins and plasticizers. It is used in cross-linked finishes to improve dry-to-touch time, reduce cratering, provide better pigment dispersion and improve coating performance. CAB-553 is soluble in alcohol and organic solvents, it even tolerates a substantial portion of water. CAB-553-0.4 is also used in nail care products for its compatibility and solubility in alcohols. it provides improved clear film, flow and dry-time. Viscosity ASTM-A, sec: 0.16 - 0.40 Acetyl by GC, wt%: 4 Max Butyryl by GC, wt%: 44- 50 Free acidity, ppm: 300 Max Moisture, wt%: 3.0 Max Hydroxyl, wt%: 4.0 - 5.0 Soluble in alcohol Improve flow and leveling Reduce cratering Reduce dry time Provide polishability Improve sprayability Pigment dispersion medium Metallic pigment control Redissolve resistance Sag resistance Enhanced color uniformity Decreased sand scratch telegraphing Intercoat adhesion

Capstone™ FS-22

Solvent-borne additive that provides low surface tension in solvent-based and high solids systems.

Capstone™ FS-22 is a nonionic fluoropolymer in methyl isobutyl ketone (MIBK) that is APEO-free and nonflammable. It works in most solvent-based and high solid systems. Appearance: Light pale to yellow liquid Composition: 30% solids in methyl isobutyl ketone (MIBK) Structure: Partially fluorinated acrylic copolymer Ionic Character: Non-ionic Specific Gravity: 0.88 g/mL Flash Point: 14 °C (57 °F) Stability: Stable to freezing. Mix well before use. Solubility: >5% in diesel fuel, mineral spirits, butyl acetate, n-heptane, toluene, xylene Low surface tension allows for better wetting, spreading, and leveling. Provides surface water and oil repellency and chemical resistance to the film. Boosts stain resistance for cleaning systems through surface energy modification. Provides foaming properties

Capstone™ FS-30

Aqueous nonionic fluorinated surfactant that is VOC-free, APEO-free, nonflammable, and stable in acidic, basic, brine, and hard water environments.

Capstone™ FS-30 is multi-use, water-soluble, ethoxylated nonionic fluorosurfactant that changes surface energies at very low concentrations. Appearance: Light yellow to amber liquid pH: 7–8.5 Specific Gravity: 1.1 g/mL Stability: Freeze-thaw stable. Stable in brine and aggressive media. Composition: 25% solids Flash Point: Nonflammable VOC-free APEO-free Compatible with additives and resins of any ionic class. Stable in acidic, basic, brine, and hard water environments. Broad pH range Water-Based Floor Care (Finishes, Waxes, and Polishes), Concentrated Cleaning Solutions, Aqueous-Based Paints and Inks, Stability and Surface Activity in Brine and Aggressive (Acidic and Basic) Media

Capstone™ FS-34

Aqueous nonionic ethoxylated fluorinated surfactant that is VOC-free, APEO-free, nonflammable, and stable in acidic, basic, brine, and hard water environments.

Capstone™ FS-34 is all-purpose, water-soluble, ethoxylated, nonionic fluorosurfactant that changes surface energies at very low concentrations. FS-34 is VOC-free, APEO-free, nonflammable, and compatible with additives and resins of any ionic class. Appearance: Light yellow to dark amber liquid pH: 5.5-7.5 g/mL Specific Gravity: 1.10 Stability: Freeze-thaw stable Composition: 25% solids Shelf Life: 5 years VOC-free APEO-free Nonflammable Compatible with additives and resins of any ionic class Stable in acidic, basic, brine, and hard water environments Reduces drag-out from bath applications Provides wetting and leveling Lowers surface tension Reduces surface defects Water-Based Floor Care (Finishes, Waxes, and Polishes), Concentrated Cleaning Solutions, Aqueous-Based Paints and Inks, Stability and Surface Activity in Brine and Aggressive (Acidic and Basic) Media

Capstone™ FS-35

Aqueous nonionic fluorinated surfactant that is VOC-free, APEO-free, nonflammable, and stable in acidic, basic, brine, and hard water environments.

Capstone™ FS-35 is a nonionic fluorosurfactant that creates very low surface tension in aqueousor solvent-based products, facilitating better wetting, spreading, leveling, and other helpful properties. FS-35 is VOC-free, APEO-free, and compatible with additives and resins of any ionic class. Appearance: Light yellow to dark amber liquid pH: 5.5-7.5 g/mL Specific Gravity: 1.1 g/mL Stability: Freeze-thaw stable Composition: 25% solids Shelf Life: 5 years VOC-free APEO-free Compatible with additives and resins of any ionic class Stable in acidic, basic, brine, and hard water environments Provides wetting and leveling Lowers surface tension Reduces surface defects Compatible with hydrocarbon surfactants Improved etching efficiency Effective plating bath aid Nonflammable Floor Care, Water Based (Finishes, Waxes, and Polishes), Concentrated Cleaning Solutions, Aqueous-Based Paints and Inks, Stability and Surface Activity in Brine and Aggressive (Acidic and Basic) Media

Capstone™ FS-60

Anionic fluorinated surfactant in water/isopropanol that is APEO-free, nonflammable, and provides excellent anti-blocking, oil repellency, and dirt pick-up resistance (DPR).

Capstone™ FS-60 is a water-soluble, anionic fluorosurfactant that gives low aqueous surface tension with little foaming. This fluorosurfactant is specifically formulated for leveling of floor finishes. It is also effective at reducing the surface tension of concentrated cleaning solutions. Appearance: Light yellow to amber, clear liquid pH: 7–8 Specific Gravity: 1.1 g/mL Stability: Freeze-thaw stable Composition: 40% solids, 15% isopropyl alcohol, 45% water Shelf Life :5 years Foam: Can foam with excessive shaking Flash Point: 28 °C (82 °F) Provides leveling, anti-cratering, wetting, and blocking Good re-wet characteristics in multi-coat applications Reduces cratering and provides faster spreading Compatible with silicone additives Low foamer; ideal for coatings REACH compliant Listed on TSCA inventory Water-Based Floor Care (Finishes, Waxes, and Polishes), Aqueous-Based Paints and Coatings,

Capstone™ FS-61

Aqueous anionic fluorinated surfactant that is VOC-free, APEO-free, nonflammable, and provides excellent anti-blocking, oil repellency, and dirt pick-up resistance (DPR).

Capstone™ FS-61 is a VOC-free, APEO-free, waterbased, anionic fluorosurfactant that provides extremely low aqueous surface tension only achievable with fluorosurfactants. FS-61 offers great wetting, leveling, thin film control, anti-blocking, and oil repellency to water-based coatings. The multi functional additive of FS-61 can help simplify formulations and improve performance. Appearance: Pale yellow to dark amber liquid; clear to hazy liquid pH: 7.5–9.0 Specific Gravity: 1.1 g/mL Flash Point: Does not flash Stability: This product should be protected from freezing and is intended for use in formulations with a pH range of 6.5–12.0. Composition: 14% solids Shelf Life: 2 years Foam: Can foam with excessive shaking Anti-blocking Oil repellency Dirt pick-up resistance Wetting and enhanced leveling Reduces cratering and provides faster spreading Lowers surface tension to improve cleaning efficiency Very Low Foam REACH compliant Listed on TSCA inventory Low VOC Architectural Coatings, Water-Based Floor Care (Finishes, Waxes, and Polishes), Specialty Cleaners (metal cleaning, car washes, and glass cleaners)

Capstone™ FS-63

Similar to FS-61, but contains isopropyl alcohol.

Capstone™ FS-63 is a water-soluble, anionic fluorosurfactant that provides low aqueous surface tensions with minimal foaming. Capstone™ FS-63 offers great wetting, leveling, anti-block, and dirt pick-up resistance. Appearance: Pale yellow to amber liquid pH: 7.5–9.0 Specific Gravity: 1.1 g/mL Stability: Freeze-thaw stable. Mix well before use. Composition: 35% solids, 20% isopropyl alcohol, 45% water Shelf Life: 5 years Flash Point: 26 °C (79 °F) Foam: Can foam with excessive shaking Anti-blocking Oil repellency Dirt pick-up resistance Wetting and enhanced leveling Re-wet characteristics in multi-coat applications Reduces cratering and provides faster spreading Lowers surface tension to improve cleaning efficiency Reduced bath drag-out Very Low Foam REACH compliant Listed on TSCA inventory Architectural coatings, industrial finishes, floor care formulations, wood coatings, specialty cleaners, and metal cleaning.

Capstone™ FS-64

Aqueous anionic fluorinated surfactant that is VOC-free, APEO-free, nonflammable, and provides excellent anti-blocking, oil repellency, and dirt pick-up resistance (DPR) with a minimum of 20% renewably sourced ingredients by weight.

FS-64, a VOC-free, APEO-free, non-flammable anionic fluorosurfactant, combines the unique properties of fluorine with the strength of a DuPont™ Renewably Sourced™ material, which contains a minimum of 20% renewably sourced ingredients by weight. FS-64 is an environmentally preferred fluorosurfactant that provides all the general performance attributes you would expect from a fluorosurfactant, including: superior surface tension reduction, anti-block, oil repellency, dirt pick-up resistance (DPR), excellent leveling characteristics and stability in highly acidic and alkaline media. Appearance: Light yellow to amber, clear liquid pH: 7–9 Specific Gravity: 1.1 g/mL Stability: Freeze-thaw stable. Mix well before use. Composition: 15% solids Shelf Life: 5 years Flash Point: Does not flash Anti-blocking Oil repellency Wetting and enhanced leveling Reduces cratering and provides faster spreading Lowers surface tension to improve cleaning efficiency Compatible with silicone additives REACH compliant Listed on TSCA inventory Architectural coatings, Industrial finishes, Water-Based Floor Care (Finishes, Waxes, and Polishes), Concentrated Cleaning Solutions, Additive to Water-Based Paints and Coatings

Capstone™ FS-65

Aqueous nonionic fluorinated surfactant that is VOC-free, APEO-free, and stable in acidic, basic, and brine environments.

FS-65 is VOC-free and APEO-free, and has a strong non-ionic character under all conditions. It is stable in acidic, basic and brine environments. In addition to providing superior performance, FS-65 meets the OECD 301B test methods criteria pertaining to biodegradability. Appearance: Yellow to amber liquid pH: 7.5–9 Specific Gravity: 1.1 g/mL Stability: Mix well before use. Freeze-thaw stable. Warm the product to room temperature, and mix before use after cold storage. Stable in brine and aggressive media. Composition: 25% solids Shelf Life: 5 years Foam: Can foam with excessive shaking VOC-free Water-soluble Anti-blocking Oil repellency Low foaming Wetting and enhanced leveling Reduces cratering and provides faster spreading Lowers surface tension to improve cleaning efficiency REACH compliant Listed on TSCA inventory Architectural coatings, Industrial finishes, Water-based floor care (Finishes, Waxes, and Polishes), Concentrated cleaning solutions, Additive to water-based paints and coatings, etching applications, Stability and Surface Activity in Brine and Aggressive (Acidic and Basic) Media

Capstone™ FS-81

Aqueous nonionic fluoropolymer that can be combined with anionic fluorosurfactants to provide optimal performance for dirt pickup resistance (DPR).

APEO-free, non-flammable FS-81 is a self-dispersed, waterborne, partially fluorinated polymeric coating additive designed to improve cleanability of oily dirt and common household stains on flat architectural waterborne coatings and latex paints. Appearance: Off-white to yellow liquid Use Rate: (active ingredient) 0.1–0.2% 0.1–0.3% 0.07–0.1% Density: 1.08 g/mL Flash Point: >200 °F (93 °C) Composition: 33% active ingredient Foam: FS-81 has very low foam and does not cause additional foam in coating systems. Odor: Faint methyl isobutyl ketone odor Solubility: Dispersible directly in latex paint. The product can be diluted with water and has limited solubility in polar solvents. Shelf Life: Three years after production under normal storage conditions Low sheen Improves oil contact angles on interior, flat finish, Easy Clean latex coatings Improved cleanability of oily, dirt-based stains, such as dirty handprints, and other household stains Improved performance with dirt pickup resistance (DPR). Does not interfere with re-coat adhesion and does not affect water repellency Low Foaming Interior and exterior latex paints, oil-based stains, printing inks, architectural paints, waterborne coatings

Capstone™ ST-100HS

Cationic aqueous fluorochemical dispersion that provides a durable, non-film forming, transparent protective barrier against oil and water on porous mineral surfaces. pH 3.5-5.

Capstone™ ST-100HS is a cationic aqueous fluorochemical dispersion that provides a durable, non-film forming, transparent protective barrier against oil and water on porous mineral surfaces. pH 3.5-5. Capstone™ ST-100HS provides oil and water repellency, stain resistance, and good stain cleanup. It can also be used in cleaning and protecting product formulations. Appearance: Clear to slightly hazy, colorless to yellow liquid Stability: Stable at normal temperatures; perishable if frozen pH: 3.5–5 Active Solids, % 25 Density, g/mL 1.104 Flash Point (Closed Cup), °C (°F) Not flammable Boiling Point, °C (°F) ~100 (~212) Freezing Point, °C (°F) ~0 (~32) Shelf Life: 2 years Spray: Consumer spray applications with pressure below 60 psi Durable protection from staining Superior oil and water repellency Retains the natural appearance of stone, tile, concrete or masonry Allows substrate to breathe (non-film forming) Easy to clean and maintain Preserves the beauty of natural stone and tile Capstone™ ST-100HS is a repellent used in water-based penetrating sealers for natural stone, unglazed tile, grout, terra cotta, concrete, and brick.

Capstone™ ST-110

Capstone™ ST-110 is the same chemistry as ST-100HS, except has a higher pH of 4-6.

Capstone™ ST-110 is a cationic aqueous fluorochemical dispersion that provides a durable, non-film forming, transparent protective barrier against oil and water on porous mineral surfaces. Appearance: Clear to slightly hazy, colorless to yellow liquid Stability: Stable at normal temperatures; perishable if frozen pH: 4–6 Active Solids, % 25 Density, g/mL 1.1 Flash Point (Closed Cup), °C (°F) Not flammable Boiling Point, °C (°F) ~100 (~212) Freezing Point, °C (°F) ~0 (~32) Shelf Life: 2 years Spray: Consumer spray application Durable protection from staining Superior oil and water repellency Retains the natural appearance of stone, tile, concrete or masonry Allows substrate to breathe (non-film forming) Easy to clean and maintain Preserves the beauty of natural stone and tile Is in compliance with REACH requirements Is listed on TSCA inventory Capstone™ ST-110 is used in water-based penetrating sealers, especially for natural stones, unglazed tile, grout, terra cotta, concrete, and brick. The product may be applied using a saturated brush, roller, paint pad, mop, or low-pressure garden-type sprayer in one or two layers (to ensure complete coverage).

Capstone™ ST-200

Solvent-based fluorochemical dispersion that provides a durable, non-film forming, transparent protective barrier against oil and water on porous mineral surfaces.

Capstone™ ST-200 is a solvent-based fluorochemical dispersion that provides a durable, non-film forming, transparent protective barrier against oil and water on porous mineral surfaces. Appearance: Colorless to yellow liquid Stability: Product gels below 0 °C (32 °F) Product is freeze/thaw stable Active Solids, % 35 Solvent, % 65 Density, g/mL 0.968 Flash Point (Closed Cup), °C (°F) 28 (82) Boiling Point, °C (°F) 120 (248) Shelf Life: 2 years Spray: Can be used in consumer spray Durable protection from staining Superior oil and water repellency Retains the natural appearance of stone, tile, concrete or masonry Allows substrate to breathe (non-film forming) Easy to clean and maintain Preserves the beauty of natural stone and tile Is in compliance with REACH requirements Is listed on TSCA inventory Capstone™ ST-200 is a repellent used in solvent-based penetrating sealers, especially for low-porosity stone, unglazed tile, grout, terra cotta, concrete, and brick. The product may be applied using a saturated brush, roller, paint pad, mop, or spray applicator (including pressurized aerosol sprayers) in one or two layers (to ensure complete coverage).

Capstone™ ST-300

VOC-free, anionic aqueous fluorochemical dispersion that provides a durable, non-film forming, transparent protective barrier against oil and water on porous mineral surfaces. pH 7.5-9.

Capstone™ ST-300 is a VOC-free, anionic aqueous fluorochemical dispersion that provides a durable, nonfilm forming, transparent protective barrier against oil and water on porous mineral surfaces Appearance: Colorless to yellow liquid Stability: Stable at normal temperatures. Perishable if frozen. Viscosity may increase with time or cold storage pH: 7.5–9 Active Solids, %: 14 Density, g/mL: 1.1 Flash Point (Closed Cup), °C (°F) Not flammable Boiling Point, °C (°F) ~100 (~212) Freezing Point, °C (°F) ~0 (~32) Shelf Life: 2 years Spray: Do not spray Durable protection from staining Superior oil and water repellency Retains the natural appearance of stone, tile, concrete or masonry Allows substrate to breathe (non-film forming) Easy to clean and maintain Preserves the beauty of natural stone and tile Is in compliance with REACH requirements Is listed on TSCA inventory Capstone™ ST-300 is a repellent used in water-based penetrating sealers for stone, unglazed tile, grout, terra cotta, concrete, and brick. Capstone™ ST-300 provides oil and water repellency, stain resistance, and easy stain cleanup

Capstone™ ST-500

Capstone™ ST-500 is the same chemistry as ST- 300, except has a higher pH of 9-11.

Capstone™ ST-500 is a VOC-free, anionic aqueous fluorochemical solution that provides a durable, non-film forming, transparent protective barrier against oil and water on porous mineral surfaces. Appearance: Colorless to amber liquid Stability: Stable at normal temperatures. Perishable if frozen pH: 9–11 Active Solids, % 25 Density, g/mL 1.1 Flash Point (Closed Cup), °C (°F) Not flammable Boiling Point, °C (°F) ~100 (~212) Freezing Point, °C (°F) ~0 (~32) Shelf Life: 2 years Spray*: Can be used in consumer spray, including aerosol spray cans Durable protection from staining Superior oil and water repellency Retains the natural appearance of stone, tile, concrete or masonry Allows substrate to breathe (non-film forming) Easy to clean and maintain Preserves the beauty of natural stone and tile Is in compliance with REACH requirements Is listed on TSCA inventory Capstone™ ST-500 is a repellent used in water based penetrating sealers for stone, unglazed tile, grout, terra cotta, concrete, granite, and brick. Capstone™ ST-500 provides oil and water repellency, stain resistance, and easy stain cleanup.

CHDA HP

Excellent thermal stability for lower resin color and good humidity resistance.

Eastman™ CHDA HP is a cycloaliphatic diacid that offers many benefits to polyester resins for coatings and fiberglass-reinforced plastics. CHDA is approved in US and Europe for use in polyester resins to be used in food contact coatings. Appearance: White to off-white powder Viscosity @ 25°C: 6.9 cP Flash point: 235°C (455°F) Melting point: 164-167°C (327-333°F) Specific gravity @ 20°C/20°C: 1.38 Solubility in water @ 20°C: 1 wt% CAS: 1076-97-7 Rapid esterification Low resin color Harness and flexibility blaance Improved corrosion and stain resistance Better hydrolytic stability Great gloss retention and prevents yellowing Used in polyester resins for coatings and fiberglass-reinforced plastics. Can also be used in improving performance in waterborne, high solids, powder coatings, and coil coating applications.

CHDM D

Offered white waxy solid form. Requires a hot room or drum heater to melt the contents for removal.

Eastman™ CHDM-D is a cycloaliphatic glycol used to make saturated and unsaturated polyester resins. It is often used in conjunction with Eastman NPG™ as a glycol modifier for resins. Appearance: White waxy solid Viscosity @ 23°C: 877 cP Flash point: 167°C (333°F) Boiling point: 284-288°C (543-550°F) Melting point: 41-61°C (106-142°F) Specific gravity @ 20°C/20°C: 1.02 CAS: 105-08-8 Hardness and Flexibility balance High crystallinity Excellent humidity and corrosion resistance Good heat resistance Highly reactive hydroxyl groups Rapid esterification and cure Used in many applications such as building materials, coil coatings, contruction chemicals, machinery coatings, paints, drink packaging, polymer modification, and protective coatings.

CHDM D90

In solution of approximately 90% by weight CHDM-D and 10% water. Solution is liquid at room temperature for easier handling.

Eastman™ CHDM-D90 is a cycloaliphatic glycol in liquid form at room temperature. Used mostly to make saturated and unsaturated polyester resins. The 10 weight percent water in CHDM-D90 is removed during heating of the resin reaction process. Can also be used as a glycol modifier with Eastman NPG™ for resins. Appearance: Slightly hazy liquid Viscosity @ 23°C: 915 cP Flash point: 167°C (333°F) Boiling point: 284-288°C (543-550°F) Melting point: 41-61°C (106-142°F) Specific gravity @ 20°C/20°C: 1.02 CAS: 105-08-9 (90%) CAS: 7732-18-5 (10%) Hardness and flexibility balance High crystallinity Excellent humidity and corrosion resistance Good heat resistance Highly reactive hydroxyl groups Rapid esterification and cure Used in many applications such as automotive coatings, paints, industrial coatings, protective coatings, and process additives.

CP 310W

A water dispersed chlorinated polyolefin adhesion promoter with 30% solids by weight

A water dispersed chlorinated polyolefin with ammonia as a neutralizing amine and 24% CPO by weight content. Useful as a primer in adhesion promoters that are air dried prior to applying a topcoat. Solids: 30 wt % CPO: 24 wt % pH @25°C: 9-10 Amine: Ammonia Shelf, 1 yr: No change @50°C, 4wk: Slight settle Freeze thaw: Good Wt/Vol: 1012 g/L (8.4 lb/gal) Viscocity, Brookfield: 10 cP Chlorination: 18-23 % Water: 69 wt % color, Gardner: Beige Specific Gravity @25°C/25°C: 1.008 Used in primer for PP and TPO Compatible with most Polyurethane and acrylics dispersions resins Co-solvents can be added to improve wetting of the substrate Adhesion promoter in paints Coatings in automotive plastics Automotive OEM Coatings for plastic parts

CP 347W

A water dispersed chlorinated polyolefin with 25% solids by weight.

A water dispersed chlorinated polyolefin containing 2-amino-2-methyl-1-propanol as a neutralizing amine and 20% CPO by weight content. Compatible with other waterborne resins making it more useful as an additive. also Compatible with many amine-neutralizable solution resins. Solids: 25 wt % CPO: 20 wt % pH @25°C: 9-10 Shelf, 1 yr: No change @50°C, 4wk: No change Freeze thaw: Good Wt/vol: 1010-1030 g/L (8.4-8.6 lb/gal) Viscosity, Brookfield: 10cP Chlorination: 18-23% Water: 74 wt % Color, Gardner: Tan Specific gravity @25°C: 1.020 Used in primer for PP and TPO Used as a stir-in additive in waterborne coatings to improve adhesion to PP and TPO Compatible with most Polyurethane and acrylics dispersions resins Co-solvents can be added to improve wetting of the substrate Adhesion promoter for paints Automotive OEM Coatings Coatings for automotive plastics Coatings for plastics parts Graphic arts General industrial coatings

DMAA (Dimethylacetoacetamide)

Liquid containing 20% water, used as a general-purpose copromoter for many unsaturated polyester formulations.

Eastman™ DMAA (N-Dimethylacetoacetamide) is a low color generating copromotor in many resin based formulations. It has shown better performance compared with DMA as a copromoter at equivalent treat rates in PG, NPG, and other glycols. Appearance: Liquid Assay: 79-83 wt% Specific gravity @ 20°C/20°C: 1.06 Flash point open cup: 122°C (252°F) Water: 17-21 wt% Molecular weight: 129.2 CAS: 2044-64-6 Low color and toxicity Easy handling with liquid form Used as a copromoter for paints and coatings and intermediate manufacturing for agricultural chemicals.

DMCD (Dimethyl Cyclohexanedicarboxylate)

Excellent weathering, flexibility and thermal stability in gel coats.

Eastman™ DMCD is a cycloaliphatic diester with low melting capabilities for synthesizing polyesters, polyamides, alkyds, and plasticizers. Similar performance properties to CHDA, except the reaction with glycols is a transesterification where methanol rather than water evolves from the reaction. Appearance: Partially crystallized liquid Viscosity @ 20°C: 8 cP Flash point: 132°C (270°F) Boiling point @ 100 mm Hg: 176°C (349°F) Vapor pressure @ 170.8°C: 50 mm Hg Specific gravity @ 35°C/4°C: 1.102 CAS: 94-60-0 Solid form is easy to melt Lower resin solution viscosity Better resin hydrolytic stability Better coating flexibility Chemical and corrosion resistance Used to formulate waterborne polyester resins for automotive, industrial maintenance, and general metal applications. Can also be used to make polyester polyols for polyurethane coatings.

DryFilm RA Dispersion

A 15% solids dispersion of specialty sized polytetrafluoroethylene (PTFE) in HFC 43-10 solvent.

DryFilm RA dispersions is a very stable lubricant, suitable for dry film lubrication. Mold release and anti-stick applications. Solids, wt%: 15 Melting Point: 300 °C (581 °F) Molecular Weight: 3000 Density, g/cc: 2.2 Particle Size, μm: Mean: 3.7, Range: 1-15 Volatiles, %: 85 Odor: Oderless Form: Fluid Dispersion Color: Translucent Specific gravity: 1.63 Density, lb/gal: 13.6 Solvent: HFC 43-10 Low coefficient of friction Superior effectiveness as a dry lubricant Enhance lubricity Promote thickening Retard fouling Release agent in processes for molding of rubber and plastic parts, dry lubricant for leather, plastics and elastomers, coating and production of metal, fabrics, thread, cord twine, rope, additives for paints and finishes, paper and carbon paper coatings, and printing and writing inks.

EAA Kosher

Tautomer at room temperature, its a colorless liquid with a fruity odor.

Eastman™ EAA consists of 8% enol and 92% keto commonly used as a low color-generating copromoter to formulate unsaturated polyester resins. It is soluble in common organic solvents and water to fit many application needs. Appearance: Liquid Molecular weight: 130.14 cP Flash point: 68°C (157°F) Boiling point: 180.8°C (357.4°F) Melting point: -45°C Specific gravity @ 20°C/20°C: 1.03 CAS: 105-45-3 Kosher certified Fruity odor Low color Readily soluble in styrenated resins Used as a copromoter in paints and coatings and used as an intermediate for herbicides and insecticides.

Eastman DTBHQ Crystalline

Storage stability inhibitor - extends shelf life with minimum effects on gel time (unsaturated polyesters).

Eastman™ DTBHQ (2,5-ditert-butylhydroquinone) is a crystalline solid that has low vapor pressure and short induction periods in peroxide-catalyzed polymerizations. Insoluble in water and caustic solutions, used as an antioxidant or co-inhibitor to prevent oxidation and extend shelf life in many industrial applications. Appearance: White to tan crystals Flash point: 216°C (420°F) Melting point: 215°C (419°F) Boiling point: 321°C (610°F) Specific gravity: 1.07 CAS: 88-58-4 Scavenges radicals slowly Storage stability inhibitor with minimum effect in gel time Stabilizes against odor and color development Used as a stopping agent in rubber emulsions and anti-skinning agent in paints.

Eastman MTBHQ Dry

Secondary inhibitor (co-inhibitor) and antioxidant for nonfood fats and oils.

Eastman™ MTBHQ (mono t-butyl hydroquinone) is commonly used as a polymerization inhibitor and antioxidant in many industrial applications. Effective in higher temperatures due to its higher solubility and potency compared to unsubstituted hydroquinone. Appearance: Light tan solid Flash point: 171°C (340°F) Boiling point: 295°C (563°F) Melting point: 125°C (257°F) Specific gravity 20°C/20°C: 1.05 Molecular weight: 166.22 CAS: 1948-33-0 Very effective polymerization inhibitor Good performing antioxidant in unstable organic liquids Excellent performance as a heat and stabilizer for pressure-sensitiveness adhesives Used as a polymerization inhibitor and industrial antioxidant in many applications.

Eastman™ THQ Toluhydroquinone

Highly effective process inhibitor used in the production of highly reactive unsaturated polyesters.

Eastman™ THQ (Toluhydroquinone) is a tan to white crystalline solid that goes through similar chemical reactions as Hydroquinone. However, due to the presence of a methyl group in the ortho position, THQ becomes a highly active inhibitor in the free radical polymerization of vinyl monomers and unsaturated polyesters. Appearance: Off-white solid Flash point: 172°C (342°F) Boiling point: 279°C (534°F) Melting point: 127°C (261°F) Specific gravity: 1.3 Molecular weight: 124.13 CAS: 95-71-6 Better solubility in styrene than Hydroquinone Highly effective cook stabilizer in unsaturated polyesters Good performing antioxidant for oleates, linseed oil, and other nonfood fats and oils Used as an inhibitor, antioxidant, and intermediate manufacturing.

Elvacite® 2013

Elvacite®2013 is a unique acrylic resin that also complies with compositional requirements of the FDA. Elvacite®2013 is softer than the methyl methacrylate grades.

Elvacite® thermoplastic acrylic resin copolymers or polymers are seen in solvent-applied high-quality coatings. Due to the wide range of attributes, Elvacite® is suitable for numerous applications. Appearance: Solid beads Specific gravity: 1.15 @ 25°C Glass transition temp, onset: 76°C Molecular weight: 34,000 Particle size (D50): 160-200 microns Acid number: 5 Tensile strength: 1,600 psi Elongation at break (23°C, 50% R.H.): 0.5% Methacrylic acid: 0.55-0.75% Inherent viscosity: 0.156 - 0.174 % Moisture: 0.35 (max) Fast dissolving Low viscosity Fast solvent release

Elvacite® 2014

Medium molecular weight methyl methacrylate copolymer; the softest and most flexible of the copolymer grades and provides great pigment wetting. Elvacite® 2014 also has a wide range of resin compatibility.

Elvacite® thermoplastic acrylic resin copolymers or polymers are seen in solvent-applied high-quality coatings. Due to the wide range of attributes, Elvacite® is suitable for numerous applications. Glass transition temperature (°C): 41 Molecular weight: 119,000 Form: Spherical beads Particle size (D50): 120-200 microns Specific gravity: 1.14 Inherent viscosity b: 0.37-0.43 Acid number: 13 Moisture (% max): 0.5 Tukon hardness, knoop no. 4 Tensile strength, psi 3,500 Elongation at break (23°C, 50% RH): 18% Increased flexibility Soluble in alcohol Increased abrasion resistance Better wear Binder for concrete sealant and coating, traffic paint, clear, translucent or pigmented metal coatings, pigmented coatings to improve pigment wetting, seamless floors

Elvacite® 2016

General purpose low viscosity, low molecular weight methyl methacrylate/n-butyl methacrylate copolymer.

Elvacite® thermoplastic acrylic resin copolymers or polymers are seen in solvent-applied high-quality coatings. Due to the wide range of attributes, Elvacite® is suitable for numerous applications. Glass transition temperature (°C): 59 Molecular weight: 60,000 Form: Spherical beads Particle size (Microtrac® D50): 170 - 265 microns Specific gravity: 1.13 Inherent viscosity b: 0.230-0.255 Acid number: 3.5 Moisture (% max): 0.50 Tukon hardness, knoop No. 8 Tensile strength, psi 2,300 Elongation at break (23°C, 50% RH): 2% Excellent hardness Low hazard High gloss Resistance to UV discoloration Fast dissolving Low viscosity Clear, translucent or pigmented metal coatings, heat seal lacquers, traffic marking paints, inks

Elvacite® 2614

A low odor version of Elvacite® 2013.

Elvacite® thermoplastic acrylic resin copolymers or polymers are seen in solvent-applied high-quality coatings. Due to the wide range of attributes, Elvacite® is suitable for numerous applications. Appearance: Solid beads Specific gravity: 1.15 @ 25°C Glass transition temp, onset: 76°C Molecular weight: 34,000 Particle size (D50): 160-200 microns Acid number: 5 Tensile strength: 1,600 psi Elongation at break (23°C, 50% R.H.): 0.5% Methacrylic acid: 0.55-0.75% Inherent viscosity: 0.156 - 0.174 % Moisture: 0.35 (max) Fast dissolving Low viscosity Fast solvent release Low odor

Elvacite® 4149

viscosity resin for coatings, inks, and adhesives.

Similar to Elvacite® 2016 but yields clear solutions in acetone. Elvacite® 4149 is a low molecular weight methyl methacrylate / n-butyl methacrylate copolymer. Elvacite® 4149 works well in clear, translucent or pigmented metal lacquers. It is a quick dissolving, low...

Elvacite® thermoplastic acrylic resin copolymers or polymers are seen in solvent-applied high-quality coatings. Due to the wide range of attributes, Elvacite® is suitable for numerous applications. Appearance: Solid bead Glass transition temp, onset: 50°C Molecular weight (Mw): 60,000 Acid number: 3.5 Inherent viscosity: 0.230 - 0.255 % Moisture: 0.50 (max) % Methacrylic acid: 0.50 - 0.70 High solids Low VOC coatings Acetone solubility Chemical resistant UV stability (non-yellowing / color retention) Protect substrate from UV degradation and plasticizer migration Used as the primary resin for primer coats, color coats protective topcoats for electronics / computers, films, plastic parts, upholstery, tarps, binders, seating, wallpaper, labels (branding), hot stamp foils

Epolene® C-10 Polymer

Epolene® C-10 is a low density polyethylene homopolymer with medium molecular weight and low color for use in adhesives, coatings and polymer compounding.

Epolene® C-10 is a branched LDPE polymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-10 has a molecular weight of 35,000. Polymer Type: LDPE Molecular Weight: 35,000 Mettler Softening Point: 101°C (ASTM D6090) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: 18,600 cP @ 125°C 3,550 cP @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat stability Hot melt adhesives, packaging, automotive coatings, wax modification, building & construction coatings, solvent-based adhesives

Epolene® C-13 Polymer

Epolene® C-13 is a low density polyethylene with medium molecular weight and low color for use in adhesives, coatings, wax modification and plastic and rubber compounding.

Epolene® C-13 is a branched LDPE homopolymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-10 has a molecular weight of 76,000. Polymer Type: LDPE Molecular Weight: 76,000 Ring and Ball Softening Point: 110°C (ASTM E 28) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: MI=190 cP @ 190°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat stability Automotive refinish, wax modification,

Epolene® C-13P Polymer

Epolene® C-13P is a low density polyethylene powder with medium molecular weight and low color for use in adhesives, coatings, wax modification and plastic and rubber compounding.

Epolene® C-13P is a branched LDPE homopolymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-10 has a molecular weight of 76,000 and is the powder form of Epolene® C-13 Polymer Type: LDPE Product Form: Powder Molecular Weight: 76,000 Ring and Ball Softening Point: 110°C (ASTM E 28) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: MI=190 cP @ 190°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat stability Automotive refinish, wax modification,

Epolene® C-15 Polymer

Epolene® C-15 is a low density polyethylene polymer with medium molecular weight and low color for use in adhesives, coatings, wax modification and color concentrates.

Epolene® C-15 is a branched LDPE homopolymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-15 has a molecular weight of 17,000 and is provided in pellet form. Polymer Type: LDPE Molecular Weight: 17,000 Ring and Ball Softening Point: 101°C (ASTM E 28) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 1,800 cP @ 190°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat seal ability Packaging, automotive refinish, wax modification

Epolene® C-15P Polymer

Epolene® C-15P is a low density polyethylene powder with medium molecular weight and low color for use in adhesives, coatings, wax modification and color concentrates.

Epolene® C-15P is a branched LDPE homopolymer that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-15 has a molecular weight of 17,000 and is provided in powder form. Polymer Type: LDPE Molecular Weight: 17,000 Ring and Ball Softening Point: 101°C (ASTM E 28) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 1,800 cP @ 190°C Low moisture vapor transmission Low color Grease resistance High gloss Good heat seal ability Packaging, automotive refinish, wax modification

Epolene® C-16 Polymer

Epolene® C-16 is a maleic anhydride modified, low density polyethylene polymer for use in adhesives, coatings, and color concentrates.

Epolene® C-16 is a branched LDPE homopolymer with maleic anhydrire that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It is well suited for applications requiring compatibility with polyamide. The maleic anhydride modification allows for improved adhesion and improved aging properties in hot melt adhesive formulations. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-16 has a molecular weight of 26,000 and is provided in pellet form. Polymer Type: Ma-PE Molecular Weight: 26,000 Ring and Ball Softening Point: 102°C (ASTM E 28) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: 2,850 cP @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Improved adhesion High filler tolerance Superior aging properties Color concentrates, automotive, wax modification, building & construction coatings, solvent-based adhesives

Epolene® C-16P Polymer

Epolene® C-16P is a maleic anhydride modified, low density polyethylene powder for use in adhesives, coatings, and color concentrates.

Epolene® C-16P is a branched LDPE homopolymer with maleic anhydride that can be used as a base polymer for coatings, adhesives, and color concentrate dispersions. It is well suited for applications requiring compatibility with polyamide. The maleic anhydride modification allows for improved adhesion and improved aging properties in hot melt adhesive formulations. It can also be used as an additive to provide lubricity in rubber compounds. Epolene® C-16P has a molecular weight of 26,000 and is provided in powder form. Polymer Type: Ma-PE Molecular Weight: 26,000 Ring and Ball Softening Point: 102°C (ASTM E 28) Penetration Hardness: 3 dmm (ASTM D5) Viscosity, Brookfield: 2,850 cP @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Improved adhesion High filler tolerance Superior aging properties Color concentrates, automotive, wax modification, building & construction coatings, solvent-based adhesives

Epolene® C-17 Polymer

Epolene® C-17 is a low density polyethylene wax with a high melt point and viscosity for use in wax blends, adhesives and color concentrates.

Epolene® C-17 is a branched LDPE homopolymer that can be used as a base polymer in concentrate dispersions and adhesives and to modify paraffin wax blends. It has a relatively high melt point and viscosity compared to other C-type Epolene products. Epolene® C-17 has a molecular weight of 100,000 and is provided in pellet form. Polymer Type: PE Molecular Weight: 100,000 Ring and Ball Softening Point: 133°C (ASTM E 28) Penetration Hardness: 2 dmm (ASTM D5) Viscosity, Brookfield: MI=19 @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Low color Excellent compatibility with tackifying resins automotive, paraffin wax modification, solvent-based adhesives, color concentrates

Epolene® C-18 Polymer

Epolene® C-18 is a low density polyethylene wax modified with maleic anhydride for use in coatings, adhesives and color concentrates.

Epolene® C-18 is a branched LDPE homopolymer modified with maleic anhydride that can be used as a base polymer in concentrate dispersions, coatings and adhesives. It is well suited for applications requiring polyamide compatibility and offers high gloss and good heat seal ability. Epolene® C-18 has a molecular weight of 15,000 and is provided in pellet form. Polymer Type: PE Molecular Weight: 15,000 Mettle Softening Point: 104°C (ASTM D 6090) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 1,550 cP @ 190°C Low moisture vapor transmission Grease resistance High gloss Good heat seal ability Low color Maleic anhydride grafted automotive, wax coatings, color concentrates

Epolene® E-14 Polymer

Epolene® E-14 is a low-density oxidized polyethylene pellet for use in adhesives, coatings, plastics and wax blends.

Epolene® E-14 is an oxidized polyethylene wax with low density and low molecular weight. It can be used in color concentrates and as a lubricant in processing rigid and flexible PVC. It is listed with the National Sanitation Foundation (NSF) under Standard 61 Drinking Water System Components Health Effects. Epolene® E-14 has a molecular weight of 4,000 and is supplied in pellet form. Polymer Type: Ox-PE Molecular Weight: 4,000 Mettle Softening Point: 104°C (ASTM D 6090) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 375 cP @ 125°C Good slip resistance High durability Produces stable emulsions NSF listed in PVC melt processes Automotive, Automotive OEM, Pressure sensitive adhesives, wax modification, PVC melt processing

Epolene® E-14P Polymer

Epolene® E-14P is a low-density oxidized polyethylene powder for use in adhesives, coatings, plastics and wax blends.

Epolene® E-14P is an oxidized polyethylene wax with low density and low molecular weight. It can be used in color concentrates and as a lubricant in processing rigid and flexible PVC. It is listed with the National Sanitation Foundation (NSF) under Standard 61 Drinking Water System Components Health Effects. Epolene® E-14P has a molecular weight of 4,000 and is supplied in powder form. Polymer Type: Ox-PE Molecular Weight: 4,000 Mettle Softening Point: 104°C (ASTM D 6090) Penetration Hardness: 4 dmm (ASTM D5) Viscosity, Brookfield: 375 cP @ 125°C Good slip resistance High durability Produces stable emulsions NSF listed in PVC melt processes Automotive, Automotive OEM, Pressure sensitive adhesives, wax modification, PVC melt processing

FG

This stearate's grade is a fine grind and fused.

Calcium stearate is a carboxylate which is formed from stearic acid and calcium oxide. Its primary uses are as a flow agent, stabilizer, thicker, and surface conditioner. APPEARANCE: WHITE POWDER FINENESS - THRU 200 MESH %: 95.0-100.0 FREE FATTY ACIDS (AS STEARIC) %: 0.0-0.5 TOTAL ASH %: 11.0-12.0 WATER %: 0.0-3.2 Great for PVC formulations, polypropylenes, and polyolefins.

FP

Calcium stearate is a carboxylate which is formed from stearic acid and calcium oxide. Its primary uses are as a flow agent, stabilizer, thicker, and surface conditioner. White powder Melting point: 160° C Flash point 349° C\ No soluble in water High Heat Stability Low Impurity Reduces Melt Viscosity

Glacial Acrylic Acid

Glacial acrylic acid (GAA) is a unsaturated monocarboxylic acid. It exhibits a pungent odor, and is clear and color less.

Building block for polymer manufacturing and chemical manufacturing. Appearance: clear and colorless Physical form: liquid at >13degC Odor: pungent Molar Mass: 72.1 Assay (Gas chromatography) - min 99.5 Water Content (ASTM E 203) - max. 0.1% Color on despatch (ASTM D 1209) - max. 20 Standard Stabilization (ASTM D 3125) 200+/- 20 ppm MEHQ Easily reacts with vinyl compounds Unsaturated carboxylic acid Stabilized with 200 ppm of MEHQ Supplied in stable form

HEUCODUR® BLACK 953-1

HEUCODUR® YELLOW 252 is an inorganic Pigment Black 28.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Black Powder Density (g/cm3): ~5.1 Bulk Volume (g/cm3): ~0.7 Tamped Density (g/cm3): ~1.7 Oil Absorption (ml/100g): ~16 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® BLUE 2R

HEUCODUR® BLUE 2R is an inorganic Pigment Blue 28.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Blue Powder Density (g/cm3): ~4.1 Bulk Volume (g/cm3): ~0.5 Tamped Density (g/cm3): ~1.0 Oil Absorption (ml/100g): 42 Water Soluble Salt (%): <0.5 Moisture (%): <0.5 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® BROWN 855

HEUCODUR® YELLOW 855 is a Pigment Brown 29 engineered specifically for coatings.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Brown Powder Density (g/cm3): ~4.6 Bulk Volume (g/cm3): ~0.5 Tamped Density (g/cm3): ~0.7 Oil Absorption (ml/100g): ~25 Water Soluble Salt (%): <0.3 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® GREEN 5G (C)

HEUCODUR® GREEN 5G is a Pigment Green 50 engineered specifically for coatings.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Green Powder Density (g/cm3): ~4.9 Bulk Volume (g/cm3): ~0.9 Tamped Density (g/cm3): ~1.5 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.5 Moisture (%): <0.5 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® GREEN 5G (P)

HEUCODUR® GREEN 5G is a Pigment Green 50 engineered specifically for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Green Powder Density (g/cm3): ~4.9 Bulk Volume (g/cm3): ~0.9 Tamped Density (g/cm3): ~1.5 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.5 Moisture (%): <0.5 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 152 (C)

HEUCODUR® YELLOW 152 is a Pigment Yellow 53 engineered specifically for coatings.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.5 Bulk Volume (g/cm3): ~0.8 Tamped Density (g/cm3): ~1.4 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 152 (P)

HEUCODUR® YELLOW 152 is a Pigment Yellow 53 engineered specifically for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.5 Bulk Volume (g/cm3): ~0.8 Tamped Density (g/cm3): ~1.4 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 154 (C)

HEUCODUR® YELLOW 154 is a Pigment Yellow 53 engineered specifically for coatings.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.5 Bulk Volume (g/cm3): ~0.8 Tamped Density (g/cm3): ~1.4 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 154 (P)

HEUCODUR® YELLOW 154 is a Pigment Yellow 53 engineered specifically for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.5 Bulk Volume (g/cm3): ~0.8 Tamped Density (g/cm3): ~1.4 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 252 (C)

HEUCODUR® YELLOW 252 is a Pigment Brown 24 engineered specifically for coatings.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.4 Bulk Volume (g/cm3): ~0.6 Tamped Density (g/cm3): ~1.2 Oil Absorption (ml/100g): ~19 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 252 (P)

HEUCODUR® YELLOW 252 is a Pigment Brown 24 engineered specifically for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.4 Bulk Volume (g/cm3): ~0.6 Tamped Density (g/cm3): ~1.2 Oil Absorption (ml/100g): ~19 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 6R (P)

HEUCODUR® YELLOW 6R is a Pigment Brown 24 engineered specifically for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.4 Bulk Volume (g/cm3): ~0.6 Tamped Density (g/cm3): ~1.1 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 7G (C)

HEUCODUR® YELLOW 7G is a Pigment Yellow 53 engineered specifically for coatings.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.5 Bulk Volume (g/cm3): ~0.8 Tamped Density (g/cm3): ~1.4 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW 7G (P)

HEUCODUR® YELLOW 7G is a Pigment Yellow 53 engineered specifically for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.5 Bulk Volume (g/cm3): ~0.8 Tamped Density (g/cm3): ~1.4 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW G 9116 (P)

HEUCODUR® YELLOW G 9116 is a Pigment Yellow 53 specifically designed for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.5 Bulk Volume (g/cm3): ~0.8 Tamped Density (g/cm3): ~1.4 Oil Absorption (ml/100g): ~17 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW G 9180 (P)

HEUCODUR® YELLOW G 9180 is a Pigment Brown 24 specifically designed for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.4 Bulk Volume (g/cm3): ~0.7 Tamped Density (g/cm3): ~1.2 Oil Absorption (ml/100g): ~16 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW G 9239 (C)

HEUCODUR® YELLOW G 9239 is a Pigment Brown 24 specifically designed for coatings.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.4 Bulk Volume (g/cm3): ~0.6 Tamped Density (g/cm3): ~1.2 Oil Absorption (ml/100g): ~19 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCODUR® YELLOW G 9239 (P)

HEUCODUR® YELLOW G 9239 is a Pigment Brown 24 specifically designed for plastics.

HEUCODUR® line of inorganic pigments are engineered to be one of the most stable pigment developed by the color industry. Due to their engineering, these pigments are highly suitable for high-temp applications. Appearance: Yellow Powder Density (g/cm3): ~4.4 Bulk Volume (g/cm3): ~0.6 Tamped Density (g/cm3): ~1.2 Oil Absorption (ml/100g): ~19 Water Soluble Salt (%): <0.1 Moisture (%): <0.1 pH: 7 - 9 Controlled particle size Enhanced dispersion capabilities Heat stability Chemical inertness

HEUCOPHOS® ZPO

HEUCOPHOS® ZPO is a zinc based anti-corrosive coating. It typically works excellent in binder systems which include HEUCORIN® RZ.

HEUCOPHOS® products offer wide spectrum anti-corrosives, high-performance polyphosphates, and modified orthophosphates to provide the most optimal anti-corrosion coatings. Zinc as Zn (%): 55.5 - 58.0 Phosphorous as PO4 3- (%): 37.5 - 39.5 Organic content (%): typ. 0.3 Loss on ignition 600°C (%): 7.0 - 11.0 Water-soluble chloride [%] max. 0.025 Water-soluble sulphate [%] max. 0.05 Conductivity [µS/cm] max. 300 pH 6.5 - 7.5 Lead as Pb [ppm] max. 10 Cadmium as Cd [ppm] max. 10 Density [g/cm3] typ. 3.6 Bulk density, untamped [g/cm3] typ. 0.5 Bulk density, tamped [g/cm3] typ. 1.0 Oil absorption value [g/100g] typ. 20 Sieve residue 32 microns [%] max. 0.01 Average particle size [microns] 2.0 - 3.5 Special organic modifications Excellent protective behavior

HEUCOSIN™ RED G 14678

HEUCOSIN™ RED G 14678 is a pigment matching RAL 3003.

Heucosin™ are ready to use dry pigment preperations. Often used in paints and coatings, this product contains both organic and inorganic pigments. Appearance: Red Powder Specific Gravity (g/cm3) (ISO 787-10): 3 Bulk Volume (l/kg) (ISO 787-11): 2.0 Oil Absorption (g/100g) (ISO 787-5): 17 Moisture (%) (ISO 787-2): 1 Very good light and weather fastness Excellent resistance to solvents, acids, and alkalis Lead chromate free

HEUCOSPERSE™ 9000 BS 9590

HEUCOSPERSE™ BS 9590 is a phthalo blue liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Blue Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.20 Total Solids (%): 52 - 57" 35% average pigment load 4:1 pigment to binder ratio Wide color selection"

HEUCOSPERSE™ 9000 BS 9593

HEUCOSPERSE™ BS 9593 is a pigment blue 15:3 in a liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Blue Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.15 Total Solids (%): 51 - 56" 35% average pigment load 4:1 pigment to binder ratio Wide color selection"

HEUCOSPERSE™ 9000 GS 9450

HEUCOSPERSE™ GS 9450 is a phthalo green liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Green Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.19 Total Solids (%): 47 - 52" 35% average pigment load 4:1 pigment to binder ratio Wide color selection"

HEUCOSPERSE™ 9000 KS 9720

HEUCOSPERSE™ KS 9720 is a carbon black in a liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Black Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.25 Total Solids (%): 47 - 52 35% average pigment load 4:1 pigment to binder ratio Wide color selection"

HEUCOSPERSE™ 9000 RS 9156

HEUCOSPERSE™ RS 9156 is a Pigment Red 57:1 in a liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Red Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.15 Total Solids (%): 40 - 46" 35% average pigment load 4:1 pigment to binder ratio Wide color selection"

HEUCOSPERSE™ 9000 YS 9342

HEUCOSPERSE™ YS 9342 is a diarylide yellow liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Yellow Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.14 Total Solids (%): 41 - 46" 35% average pigment load 4:1 pigment to binder ratio Wide color selection"

HEUCOSPERSE™ I BS 1520

HEUCOSPERSE™ BS 1520 is a phthalo blue liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Blue Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.15 Total Solids (%): 45 - 51 35% average pigment load 4:1 pigment to binder ratio Wide color selection"

HEUCOSPERSE™ I KS 1720

HEUCOSPERSE™ KS 1720 is a Pigment Black 7 liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Black Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.2 Total Solids (%): 42 - 48 High quality resinated dispersion 35% pigment load 4:1 pigment to binder ratio"

HEUCOSPERSE™ I RS 1115

HEUCOSPERSE™ RS 1115 is a Pigment Red 122 liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Red Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.14 Total Solids (%): 40 - 46 High quality resinated dispersion 35% pigment load 4:1 pigment to binder ratio

HEUCOSPERSE™ I RS 1120

HEUCOSPERSE™ RS 1120 is Pigment Red 169 liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Red Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.15 Total Solids (%): 36 - 41 High quality resinated dispersion 35% pigment load 4:1 pigment to binder ratio

HEUCOSPERSE™ I RS 1135

HEUCOSPERSE™ RS 1135 is a Pigment Red 2 liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Red Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.2 Total Solids (%): 42 - 48 High quality resinated dispersion 35% pigment load 4:1 pigment to binder ratio

HEUCOSPERSE™ I RS 1140

HEUCOSPERSE™ RS 1140 is Pigment Red 23 in liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Red Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.18 Total Solids (%): 45.8 - 51.8 High quality resinated dispersion 35% pigment load 4:1 pigment to binder ratio

HEUCOSPERSE™ I YS 1310

HEUCOSPERSE™ YS 1310 is a Pigment Yellow 83 in liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Yellow Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.11 Total Solids (%): 38 - 44 High quality resinated dispersion 35% pigment load 4:1 pigment to binder ratio

HEUCOSPERSE™ I YS 1321

HEUCOSPERSE™ YS 1321 is a arylide yellow liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Yellow Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.12 Total Solids (%): 42 - 48 High quality resinated dispersion 35% pigment load 4:1 pigment to binder ratio

HEUCOSPERSE™ III YS 5311

HEUCOSPERSE™ YS 5311 is a diarylide yellow liquid dispersion.

Heucosperse™ products are pigment dispersions specifically designed to be used within the ink industry. The high pigment loads make it an excellent resin for a variety of paper and film packaging applications. Appearance: Yellow Liquid pH (ISO 787-9): 8.5 - 9.5 Specific Gravity (lbs/gal) (ISO 787-10): 1.11 Total Solids (%): 38 - 43 Max transparency High gloss 25% average pigment load 3:2 pigment to binder ratio"

HEUCOTINT™ BU 15002

HEUCOTINT™ BU 15002 is a Pigment Blue 15:2 used in a universal tinting system.

Heucotint™ offers a variety of colorants that are VOC-free, APE-free and formadehyde free. This system of colorants offer the ease and consistancy at point-of-sale transactions. Appearance: Blue Pigment pH (ISO 787-9): 7.5 - 9.0 Specific Gravity (lbs/gal) (TMG-003) : 1.37 Grind (Hegman): 6.0 min. Wt. per Gal (lbs/gal): 10.9 - 11.9 Viscosity (Ku`s): 70.0 - 90.0 VOC (g/l): 0.0"

HEUCOTINT™ KU 17002

HEUCOTINT™ KU 17002 is a black pigment used in a universal tinting system.

Heucotint™ offers a variety of colorants that are VOC-free, APE-free and formadehyde free. This system of colorants offer the ease and consistancy at point-of-sale transactions. Appearance: Black Liquid pH (ISO 787-9): 7.5 - 9.0 Specific Gravity (lbs/gal) (TMG-003) : 1.36 Grind (Hegman): 6.0 min. Wt. per Gal (lbs/gal): 10.8 - 11.8 Viscosity (Ku`s): 70.0 - 90.0 VOC (g/l): 0.0"

HEUCOTINT™ WU 10002

HEUCOTINT™ WU 10002 s a titanium dioxide pigment used in a universal tinting system.

Heucotint™ offers a variety of colorants that are VOC-free, APE-free and formadehyde free. This system of colorants offer the ease and consistancy at point-of-sale transactions. Appearance: White Liquid pH (ISO 787-9): 7.5 - 9.0 Specific Gravity (lbs/gal) (TMG-003) : 2.08 Grind (Hegman): 6.0 min. Wt. per Gal (lbs/gal): 16.8 - 17.8 Viscosity (Ku`s): 80.0 - 100.0 VOC (g/l): 0.0"

HEUCOTINT™ XU 17005

HEUCOTINT™ XU 17005 is a brown oxide pigment used in a universal tinting system.

Heucotint™ offers a variety of colorants that are VOC-free, APE-free and formadehyde free. This system of colorants offer the ease and consistancy at point-of-sale transactions. Appearance: Brown Liquid pH (ISO 787-9): 7.5 - 9.0 Specific Gravity (lbs/gal) (TMG-003) : 1.76 Grind (Hegman): 6.0 min. Wt. per Gal (lbs/gal): 14.2 - 15.2 Viscosity (Ku`s): 80.0 - 100.0 VOC (g/l): 0.0"

HPHP Nuggets

Free-flowing nuggets in bags that have good resistance to caking.

Eastman™ HPHP is a difunctional ester-glycol used for manufacturing polyester resins for coil, powder, and automotive coatings. Similar to properties of NPG and can act as a modifier to enhance coating film properties. Appearance: White, irregularly shaped crystalline nuggets Molecular weight: 204.27 Melting point: 45-50°C (114.8-122°F) Flash point: 161°C (322°F) Boiling point @ 760 mm Hg: 293°C (495.4°F) Specific gravity @ 55°C/20°C: 1.01 CAS: 1115-20-4 Reduced resin crystallinity Lower resin Tg Improved melt flow in powder coatings Improved coating flexibility Maintains good weathering of NPG Reduces aromatic content Used for automotive primer surfaces and coil coating applications due to its ability to prevent chip resistance and increase exterior durability.

KATHON™ LX 1.5%

preservation of a finished adhesive or coating is desired, a thin film fungicide or mildewcide is needed.

Kathon LX 1.5% is a isothiazolinone-based preservative used to protect polymers, coatings, adhesives and pigments and is an effective and efficient in-can preservative for systems with pH 2-8.5, extending shelf life of a product in its wet state. If long-term...

DuPont Industrial microbicides are a collection of in-can and thin-film preservatives that are appropriate for a multitude of product applications. Physical state: liquid Color: Light blue to light green Odor: Mild, inoffensive odor pH: 2 - 4 Melting point/range: -3.00 °C ( 26.60 °F) Relative Vapor Density (air = 1): 0.6200 Relative Density (water = 1): 1.0200 Formaldehyde free Broad efficacy Low use levels Suited for formulations < pH 8.5 No VOC contribution Adhesives, paints & coatings, agriculture, latex, dispersed pigments, and building materials

KORDEK™ MLX

Kordek™ MLX is based on 10% MIT and approved for ink and similar applications.

Kordek™ MLX in-can preservative based on methyl isothiazolinone is registered and designed to preserve printing fluids, adhesives, electronic chemicals and mineral dispersions. It is approved for food contact adhesives and coatings. Physical state: liquid Color: clear Odor: Mild odor pH: 3 - 6 Melting point/range: -20 to -15 °C (-4 to -5 °F) Boiling point (760 mmHg): 100°C (212°F) Chemically stable in high pH formulations Compatible with polymer emulsions Formaldehyde free Broad spectrum efficacy Paints, adhesives, latex emulsions, tackifiers, mineral slurries, pigment dispersions

Liquid D-300 4 Sulfophthalic Acid

Sulfonic Acid that is applied as a catalyst, corrosion inhibitor, chemical intermediate and primary additive in aluminum anodizing process.

This 50% aqueous solution of 4-sulfophthalic acid is the key component of the preferred electrolyte for the production of &quot;hard&quot; anodic oxide coatings for aluminium-based alloys. These highly abrasion resistant coatings come in a number of colors, metallic and brownish gray, black, bronze and gold amking them suitable for achitectural usage. CAS Number: 89-08-7 Synonyms: 1,2-Benzenedicarboxylic acid, 4-sulfo- Phthalic acid, 4-sulfo- 4-Sulphophthalic acid Appearance @ 25°C: Clear amber liquid Odor: Odorless Active Content (Wt. %): 50.0 Sulfuric Acid (Wt. %): 2.25 max Density (lbs/Gal): 10.8 pH (10% solution): <1.0 Anodizing with Pilot D-300 efficiently produces a range of protective and decorative oxide coatings, with moderate voltage and cooling requirements. - Anodizing - Metal treatment - Coatings - Aluminum treatment

Lucite® 6751

Most optically clear of all Lucite® high molecular weight methyl methacrylate homopolymers.

Lucite® high-quality acrylic resins are designed with exact chemical properties to meet customer's needs. The production process results in pure resin that is optically pleasing. Products are seen in thousands of applications globally. Appearance: beads Rockwell Hardness (M Scale): 81 % Liminance Transmittance (0.12, 3.2mm): 92 Tensile Strength @ 23°C, 50% RH (MPa): 54 Exceptional gloss Very high surface abrasion resistance and hardness Sparkle Crystal Clarity Outstanding Ultraviolet Light Resistance Excellent Resistance to Water, Alcohol, Dilute Acids and Alkalis, Chemical Fumes and Corrosive and Oxidizing Environments

Lupasol® FG

Multi-functional cationic polyethylenimine with a branched polymer structure.

Lupasol® FG is a clear, colorless cationic polyethylenimine with a branched polymer structure. Average molar mass: 800 Viscosity @ 20°C: 5000 Concentration: 99% Adhesives, complexing, coatings and paints, pigment manufacture, and protein immobilization.

Lupasol® FT WF

Waterfree polyethylenimine with a molecular weight around 25,000.

Lupasol® FT WF is a waterfree multi-functional cationic polyethyleneimine (PEI) with a branched polymer structure. The unique properties of Lupasols allow them to promote adhesion, disperse fillers and pigments, flocculate suspended solids, enhance and modify surface characteristics, protect materials after surface modification and bind unwanted materials. Average molar mass: 25,000 Viscosity @ 20°C: 200,000 Concentration: 99% Color: clear to slightly cloudy, colorless to yellowish liquid at room temp. Miscible with water in all proportions Flowable liquids Ames negative No detectable ethylenimine importunity Three types of bonding: ionic, hydrogen and van der Waals Forces Printing inks, Adhesion promoters in car tires, Adhesives, Complexing, Plastics modification, Coatings and paints, Pigment manufacture, Protein immobilization, Textile auxiliaries, Packaging, and Water treatment.

Lupasol® G 20 WF

Waterfree polyethylenimine with a molecular weight around 1,300.

Lupasol® G 20 Waterfree, is a anhydrous multi-functional cationic polyethyleneimine (PEI) with a branched polymer structure. The unique properties of Lupasols allow them to promote adhesion, disperse fillers and pigments, flocculate suspended solids, enhance and modify surface characteristics, protect materials after surface modification and bind unwanted materials. Average molar mass: 1,300 Viscosity: 8,000 Concentration: 98% Color: clear, colorless to yellowish liquid Anhydrous Miscible with water in all proportions Flowable liquids Ames negative No detectable ethylenimine importunity Three types of bonding: ionic, hydrogen and van der Waals Forces Printing inks, Adhesion promoters in car tires, Adhesives, Complexing, Plastics modification, Coatings and paints, Pigment manufacture, Protein immobilization, Textile auxiliaries, Packaging, and Water treatment.

Lupasol® PR 8515

Waterfree polyethylenimine with a molecular weight around 2,000.

Lupasol® PR 8515, is a waterfree multi-functional cationic polyethyleneimine (PEI) with a branched polymer structure. The unique properties of Lupasols allow them to promote adhesion, disperse fillers and pigments, flocculate suspended solids, enhance and modify surface characteristics, protect materials after surface modification and bind unwanted materials. Avg molar mass: 2,000 Viscosity: 14,000 Concentration: 98% Color: clear, colorless to rarely slightly yellowish liquid Compatible with cationic and nonionic systems Absorbs strongly on negatively charged surfaces Crosslinking agent Anhydrous Miscible with water in all proportions Flowable liquids Ames negative No detectable ethylenimine importunity Three types of bonding: ionic, hydrogen and van der Waals Forces Adhesives, Complexing, Coatings and paints, Pigment manufacture, and Protein immobilization.

Lupasol® SC-61B

37% aqueous solution of a hydroxyethylated polyethylenimine.

Lupasol® SC-61B is a hydroxyethlyated water soluble polyethylenimine formed by reaction of a high molecular weight polyethylenimine with ethylene oxide. Average molecular weight: 110,000 Viscosity @ 25°C: 2,500 cP max Solid matter content, %: 35-40 Appearance: Free flowing liquid Film forming amine in coatings and printing ink, brightener in electroplating baths, cationic modifier for clays and starches, cosmetic and personal care.

MAA (Methyl Acetoacetate)

Copromoter for unsaturated polyesters, typically used in pharmaceuticals, fragrances and pesticides.

Eastman™ MAA (Methyl Acetoacetate) is a colorless liquid used mostly as an intermediate for agricultural and pharmaceutical chemicals. MAA develops desirable hardness more rapidly than resins copromoted with DMA at equivalent treat rates. Appearance: Liquid Molecular weight: 116.1 Flash point: 74°C (165°F) Boiling point: 166°C (331°F) Melting point: -55°C Specific gravity @ 20°C/20°C: 1.078 CAS: 105-45-3 Low toxicity Low viscosity Extended gel time compared with DMA Does not impart brown color to polyesters compared to amine promoters Readily soluble in styrenated resins Used as a process solvent and intermediate manufacturing for herbicides, insecticides, and pharmaceutical chemicals.

METHOCEL™ 240S

METHOCEL™ 240S has the same properties as METHOCEL™ 240, except 240S is surface-treated and can be added directly to an aqueous system to dissolve.

METHOCEL™ is a hydroxypropyl methylcellulose (HPMC) thickener. It is a water-soluble, high-purity, non-ionic cellulose ether. METHOCEL™ 240S yields high viscosity of 40000 cP at low addition levels. The 240S powder is surface-treated and can be added directly to an aqueous system to dissolve. Methoxyl: 27.0 - 30.0% Hydroxypropoxyl: 4.0 - 7.5% Sodium Chloride: Max 1.5% Viscosity, 2% in water, @20degC, calculated: 30000 - 50000 cP Surface treated Results in a semi-firm gel texture Highly soluble in cold water Able to revert back to liquid form when cooling down

METHOCEL™ 311 Powder

METHOCEL™ 311 Powder is highly soluble in organic solvent systems. It yields a viscosity of 120,000 cP with properties similar to other HPMC grades.

METHOCEL™ is a hydroxypropyl methylcellulose (HPMC) thickener. It is a water-soluble, high-purity, non-ionic cellulose ether. METHOCEL™ 311 powder yields viscosity of 120,000 cP at low addition levels and has the highest substitution. It is designed for combined water/organic solvent systems. 311 is recommended for paint remover formulations to increase the contact time of the remover on the application surface. Methoxyl: 22.0 - 27.0% Hydroxypropoxyl: 25.0 - 32.0% Viscosity, Brookfield RVT, Spindle No. 4 @ 20rpm, 1% in Methylene Chloride, @20°C: 7,500 mPa.s Can be added directly to any solvent or solvent blend Reduced drip and solvent evaporation rate

METHOCEL™ A15C

Methocel™ A15C is a methylcellulose thickener. It performs many functions simultaneously including thickening, binding, water retention and film forming. The A15C grade has a viscosity range from 1,200 to 1,800 cP.

Methocel™ A15C is a water-soluble polymer derived from cellulose. Methocel is a high purity, non-ionic cellulose ether, and performs as a rheology modifier and functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. Sodium Chloride: max 1.5% Viscosity, 2% in water, @20°C, calculated: 1200 - 1800 cP Forms a firm gel texture Reversible hot water gelation

METHOCEL™ A15LV

Methocel™ A15LV is a low viscosity methylcellulose. With a viscosity from 12 to 18 cP, it is one of the lowest in the Methocel product range. It functions as a rheology modifier in coatings and adhesives.

Methocel™ A15LV is a low viscosity water-soluble polymer derived from cellulose. Methocel is a high purity, non-ionic cellulose ether, and performs as a rheology modifier. Further it functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. The use of Methocel contributes to economic advantages, while various properties are simultaneously present and interact in combination. Methoxyl: 27.5 - 31.5% Sodium Chloride: Max 2.0% Viscosity, 2% in water, @20degC, calculated: 12 - 18 cP Water soluble Non-ionic Forms a firm gel texture Thermally gel in solution Reversible hot water gelation

METHOCEL™ A15LV Premium

METHOCEL™ A15LV Premium has the same performance properties as METHOCEL™ A15LV, except this premium product has less impurities. It can be used in pharmaceutical applications.

METHOCEL™ A15LV Premium is a water-soluble polymer derived from cellulose with a very low viscosity. Methocel is a high purity, non-ionic cellulose ether. Besides thickening, binding, Methocel functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. The use of Methocel contributes to economic advantages, due to the fact that various properties are simultaneously present. Methoxyl: 27.5 - 31.5% Loss on drying: 5.0% Max Residue on ignition: 1.5% Max Ash sulphated: 1.5% Max Sodium Chloride: Max 2.0% Viscosity, 2% in water, @20degC, calculated: 12 - 18 cP Pharmaceutical grade USP/EP/JP compliant Water soluble Non-ionic Forms a firm gel texture Thermally gel in solution Reversible hot water gelation

METHOCEL™ A4C

METHOCEL™ A4C is a low viscosity methylcellulose thickener. It yields a viscosity of 400 cP at low addition levels.

Methocel™ A4C is a water-soluble, high purity, non-ionic cellulose ether, and performs as thickener, binder and film former. Further it functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. Methocel contributes to economic advantages due to the fact that properties are simultaneously present. Methoxyl: 27.5 - 31.50% Sodium Chloride: max 2.0% Viscosity, 2% in water, @20°C, calculated: 350 - 550 cP Yields optimum performance at a lower concentration Can be added directly to aqueous systems Non-ionic pH stable Thermal gelation which is reversible For Application specific details, Visit Methocel A4C page on DuPont Cellulosic dedicated website. Learn More!

METHOCEL™ A4C Premium

METHOCEL™ A4C Premium has the same performance as METHOCEL™ A4C, except this premium product is pharmaceutical compliant.

Methocel™ A4C Premium is a water-soluble, high purity, non-ionic cellulose ether. It has a low viscosity range of 320 to 480 cps. Methocel is used as thickener, binder and film former. Further it functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. Methocel contributes to economic advantages due to the fact that properties are simultaneously present. Methoxyl: 27.5 - 31.5% Loss on drying: 5% Max Residue on ignition: 1.5% Max pH, 2% in water: 5.0 - 8.0 Viscosity, 2% in water, @20degC, calculated: 320 - 480 cP Pharmaceutical grade Yields optimum performance at a lower concentration Can be added directly to aqueous systems Non-ionic pH stable Thermal gelation which is reversible USP/EP/JP compliant

METHOCEL™ A4M

METHOCEL™ A4M is a methylcellulose and yields a viscosity of 4,000 cP. It is used as thickener, binder, film former, and water-retention agent.

METHOCEL™ A4M is a water-soluble methylcellulose. Methocel products also function as suspension aids, surfactants, lubricant, protective colloids, and emulsifiers. Many useful properties are simultaneously present resulting in a significant economic advantage. Methoxyl: 27.5 - 31.5% Sodium Chloride: Max 1.5% Viscosity, 2% in water, @20degC, calculated: 3,500 - 5,600 cP Yields optimum performance at a lower concentration Water soluble No ionic charge pH stable Thermal gelation which is reversible

METHOCEL™ E15 Industrial LV

METHOCEL™ E15 Industrial LV is an HPMC with a low viscosity of 15 cP. Solutions of this grade can be made at 10% to 15% concentration.

METHOCEL™ E15LV is water-soluble and non-ionic cellulose ether. It is often used as a thickener or binder. Methocel has various other functions which are often simultaneously present in the formulation resulting in economical advantages. It can perform as suspending aid, stabilizers, surfactants, lubricants, protective colloids, and emulsifiers. Methoxyl: 28 - 30% Viscosity, 2% in Water, @ 20degC: 12 - 18 cP Hydroxypropoxyl: 7.0 - 12.0% Forms a semi firm gel texture Thermally gel in solution Reversible hot water gelation

METHOCEL™ E5 Premium LV

METHOCEL™ E5 Premium LV is a Hydroxypropyl Methylcellulose (HPMC) thickener which yields a very low viscosity of 5 cP. It is a pharmaceutical grade.

METHOCEL™ E5 Premium LV is a water-soluble polymer derived from cellulose. This pharmaceutical grade can be used in Industrial applications. Methocel products are used as thickeners, binders, water retention aids, and also function as suspension aids, surfactants, lubricity aids, and emulsifiers. Since various properties are present in a formulation Methocel is an economical preferred choice versus other polymers. Viscosity, 2% in water @20°C: 4.0 - 6.0 cP Methoxyl: 28.0 - 30.0% Hydroxypropoxyl: 7.0 - 12.0% Loss on Drying: 5.0% Max Residue on Ignition: 1.5% Max pH, 2% in water: 5.0 - 8.0 Compliant with US, JP, EUR Pharmacopeia U.S. FDA Gras This grade can be used in Industrial applications.

METHOCEL™ F4M

METHOCEL™ F4M is a Hydroxypropyl Methylcellulose (HPMC) thickener. At addition levels of 2 to 3% it yields a viscosity of 4,000 cP. It is widely used in ceramics processing, coatings, adhesives and chemical processing.

METHOCEL™ F4M is a water-soluble polymer derived from cellulose. Methocel products are used as thickeners, binders, water retention aids, and also function as suspension aids, surfactants, lubricity aids, and emulsifiers. Since various properties are present in a formulation METHOCEL™ is an economical preferred choice versus other polymers. Methoxyl: 27.0 - 30.0% Hydroxypropoxyl: 4.0 - 7.5% Viscosity, 2% in water @20°C: 3,500 - 5,600 cP Yielding optimum performance at a lower concentration Can be added directly to aqueous systems No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ F4M Food Grade

METHOCEL™ F4M Food Grade has the same characteristics as METHOCEL™ F4M, except its compliance with Food standards.

METHOCEL™ F4M Food is a water-soluble polymer derived from cellulose. This grade complies with the most common Food standards. Methocel products are used as thickeners, binders, water retention aids, and also function as suspension aids, surfactants, lubricity aids, and emulsifiers. Since various properties are present in a formulation Methocel is an economical preferred choice versus other polymers. Methoxyl: 27.0 - 30.0% Hydroxypropoxyl: 4.0 - 7.5% Viscosity, 2% in water @20°C: 3,500 - 5,600 cP Food compliancy; FCC, EC, FAO/WHO, GRAS, U.S. FDA Yielding optimum performance at a low concentration Can be added directly to aqueous systems No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ F4M Premium

METHOCEL™ F4M Premium is a pharmaceutical grade with the same properties as F4M.

METHOCEL™ F4M is a water-soluble polymer derived from cellulose. Methocel products are used as thickeners, binders, water retention aids, and also function as suspension aids, surfactants, lubricity aids, and emulsifiers. Since various properties are present in a formulation Methocel is an economical preferred choice versus other polymers. Viscosity, 2% in water @20°C: 2,663 - 4970 Methoxyl: 27.0 - 30.0% Hydroxypropoxyl_ 4.0 - 7.5% Loss on Drying: 5.0% Max Residue on Ignition: 1.5% Max pH, 2% in water: 5.0 - 8.0 Compliant with US, JP, EUR Pharmacopeia U.S. FDA Gras Limited for use in Industrial applications

METHOCEL™ F50

METHOCEL™ F50 is a low viscosity Hydroxypropyl Methylcellulose (HPMC) thickener with a low substitution. It yields viscosity of 50 cPs and forms a semi-firm gel.

METHOCEL™ F50 is a water-soluble polymer derived from cellulose. Methocel is a high purity, non-ionic cellulose ether, and performs as a rheology modifier, further it functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. Methoxyl: 27.0 - 30.0% Hydroxypropoxyl: 4.0 - 7.5% Viscosity, 2% in water @20°C: 40 - 60 cPs Gelation Temp 62-68 °C Forms a semi-firm gel Reversible hot water gelation

METHOCEL™ F50 Food Grade

METHOCEL™ F50 Food Grade has the same characteristics as F50, this grade is compliant with the main Food standards.

METHOCEL™ F50 is a water-soluble polymer derived from cellulose. Methocel is a high purity, non-ionic cellulose ether, and performs as a rheology modifier, further it functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. Methocel contributes to economic advantages compared with other polymers, because multiple properties are present simultaneously. Methoxyl: 27.0 - 30.0% Hydroxypropoxyl: 4.0 - 7.5% Viscosity, 2% in water @20°C: 40 - 60 cPs Moisture: 5.0% Max Residue on Ignition: 1.5% Max Sulfiting Agents, as Sulfur Dioxide: 10 ppm Max Lead: 2 ppm Max Food compliancy; FCC, EC, FAO/WHO, GRAS, U.S. FDA Gelation Temp 62-68 °C Forms a semi-firm gel Reversible hot water gelation Can be added directly to aqueous systems No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling Use in Industrial application where Food grade is required.

METHOCEL™ J12MS

METHOCEL™ J12MS is a surface treated HPMC resulting in delayed viscosity build up to 12,000 cPs. It has one of the highest substitution levels.

METHOCEL™ J12MS is a hydroxypropyl methylcellulose (HPMC). It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products function as thickener, binder and rheology modifier. The combination of properties present simultaneously brings economic advantages versus other polymers. Methoxyl: 16.5 - 20.0% Hydropropoxyl: 23.0 - 32.0% Viscosity, 2% in water @20°C: 10,000 - 16,500 cPs

METHOCEL™ J75MS

METHOCEL™ J75MS is a Hydroxypropyl Methylcellulose (HPMC) thickener with very high substitution. Is has a viscosity range from 60,000 to 75,000 cPs at low addition levels. This grade is surface treated with a slow viscosity build up.

METHOCEL™ J75MS is a hydroxypropyl methylcellulose (HPMC). It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products function as thickener, binder and rheology modifier. The combination of properties present simultaneously brings economic advantages versus other polymers. Methoxyl: 16.5 - 20.0% Hydroxypropoxyl: 23.0 - 32.0% Viscosity, 2% in water @20°C: 60,000 - 90,000 cP Can be added directly to aqueous systems No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ K100LV

METHOCEL™ K100LV is a hydroxypropyl methylcellulose (HPMC) thickener with low substitution. It has a low viscosity of 100 cP at low addition levels.

METHOCEL™ K100LV is a low viscosity methylcellulose polymer. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 80 - 120 cP Moisture, as packaged: 3.0 Max Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ K15M

METHOCEL™ K15M is a HPMC thickener with low substitution. It yields a viscosity of 15,000 cP and forms a soft gel texture. This Methocel has the highest gelation temperature of 70°C-90°C (158°F-194°F).

METHOCEL™ K15M is a hydroxypropyl methylcellulose. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 10,000 - 18,000 cP Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ K15M Food Grade

METHOCEL™ K15M Food Grade is the same as K15M, but is compliant with international Food standards.

METHOCEL™ K15M Food grade is a hydroxypropyl methylcellulose. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 11,250 - 21,000 cPs Food compliancy; FCC, EC, FAO/WHO, GRAS, U.S. FDA Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling Can be used in Industrial applications.

METHOCEL™ K15MS

METHOCEL™ K15MS is similar to K15M, except it is surface treated for a retarded dissolution.

METHOCEL™ K15M is a hydroxypropyl methylcellulose. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 10,000 - 18,000 cP Delayed dissolution Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ K4M

METHOCEL™ K4M ia a hydroxypropyl ethylcellulose (HPMC) thickener with a low substitution. It has a viscosity of 4,000 cP at low addition levels.

METHOCEL™ K4M is a hydroxypropyl methylcellulose. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 12,000 - 21,000 cP Sodium Chloride: 2.0 Max Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

Methyl Acrylate

Methyl acrylate (MA) is an enoate ester. It's a volatile colorless liquid with a flash point of 27°F.

Building block for polymer manufacturing and chemical manufacturing. Appearance: clear and colorless Physical Form: liquid Odor: penetrating Molar Mass: 86 Assay (Gas chromatography) - min 99.8% Water Content (ASTM E 203) - max. 0.05% Acid Content (ASTM D 1613) - max. 0.009% Color on despatch (ASTM D 1209) - max. 10 Standard Stabilization (ASTM D 3125) 15+/- 5ppm MEHQ Readily undergoes addition reactions with a wide variety of organic and inorganic compounds Can be used as moisture barrier for latex formulations

MONOLITE™ BLUE 515303

MONOLITE™ BLUE 515303 is an organic pigment in the color of Pigment Blue 15:3.

Monolite™ is a line of high-performance organic pigments specifically designed for the coatings and paint industry. These organic pigments offer the highest tint strength and excellent brilliance. Appearance: Blue Powder Density (g/cm3): 1.5 Bulk Volume (l/kg): 3.5 Specific Surface (m3/g): 54 Oil Absorption (ml/100g): 52 Easy dispersibility Outstanding fastness properties

MONOLITE™ GREEN 600734

MONOLITE™ GREEN 600734 is an organic pigment in the color of Pigment Green 7.

Monolite™ is a line of high-performance organic pigments specifically designed for the coatings and paint industry. These organic pigments offer the highest tint strength and excellent brilliance. Appearance: Green Powder Density (g/cm3): 2.1 Bulk Volume (l/kg): 2.3 Specific Surface (m3/g): 47 Oil Absorption (ml/100g): 41 Easy dispersibility Outstanding fastness properties

MONOLITE™ YELLOW 113901

MONOLITE™ YELLOW 113901 is an organic pigment in the color of Pigment Yellow 139.

Monolite™ is a line of high-performance organic pigments specifically designed for the coatings and paint industry. These organic pigments offer the highest tint strength and excellent brilliance. Appearance: Yellow Pigment Density (g/cm3): 1.7 Bulk Volume (l/kg): 3.7 Specific Surface (m3/g): 19 Oil Absorption (ml/100g): 52 Easy dispersibility Outstanding fastness properties

NAUGARD™ RM51-S

Blend of phosphite and phenolic antioxidants that is extremely effective at protecting natural and synthetic rubber from degradation as a result of exposure to heat, light, and oxygen.

NAUGARD™ RM51-S is a liquid form stabilizer blend for natural and synthetic rubber. It minimizes gel formation and is exceptionally effective at protecting against degradation resulting from heat, light, and oxygen exposure. NAUGARD™ RM51-S is non-staining, non-discoloring, and stabilizes mooney viscosity in latex. Appearance: Clear gold to yellow viscous liquid Specific Gravity @ 25 °C: 0.98 Soluble: Most organic solvents Insoluble: Water Food contact approval Non-staining Non-discoloring Easily emulsified for latex applications Exceptional protection from degradation in natural and synthetic rubbers as a result of exposure to heat, light, and oxygen Minimizes gel formation during processing Dipped and extruded latex

NB-60, SW

Zinc Stearate NB-60 SW is the zinc salt of distilled hydrogenated fatty acids.

Zinc stearate is a metal salt of a fatty acid. PMC Biogenix offers zinc stearate in both precipitated and fused forms in a wide variety of end use applications. Total ash: 17.00-18.50 Water soluble salts: 0.00-0.50 Water: 0.00-1.00% Fineness thru 325 mesh: 99.80-100.00% Free fatty acids (as stearic): 0.00-2.00 Exceptional resistance to reaction with acid catalysts Soluble in many oils and waxes Can be used for lacquer sanding sealers as a sanding aid to minimize possibilities of "bloom" and "frost" development in subsequently applied top coats of synthetic varnishes containing acid catalysts.

NPG 90

Consisting of 90% NPG, and 10% water, this glycol offers a balance of hardness &amp; flexibility characteristics, as well as excellent thermal stability.

Eastman NPG™ 90 glycol is a liquid at above 38°C to form high quality polyester resins for industrial coatings and fiberglass-reinforced plastics. It is also used as an intermediate to formulate synthetic lubricants. In the U.S., NPG can legally be used for food contact coating applications under federal food additive regulations. Appearance @ 38°C (100°F): Liquid Appearance @ 150°C (77°F): Slurry Crystallization point: 31°C (88°F) Flash point: 132°C (270°F) Boiling point: 100-121°C (212-250°F) Specific gravity @ 60°C: 0.94 CAS: 126-30-7 (90%) CAS: 7732-18-5 (10%) Excellent thermal stability for low resin color Excellent weathering Good chemical, stain, and humidity resistance Good hardness and flexibility balance Rapid reaction during esterification and cure Used as a raw material in intermediate manufacturing and many coating applications.

NPG Platelets

Provides excellent weathering and fluidization characteristics.

Eastman NPG™ platelets is a glycol commonly used for high-quality polyester resins for industrial coatings and fiberglass-reinforced plastics. It can be used as the sole glycol component or used in conjunction with other modifiers to achieve your desired properties. It can be used for food contact coatings in the United States under feral food additive regulations. Appearance: White platelets Molecular weight: 104.15 Crystallization point: 31°C (88°F) Melting point: 124-130°C (255-266°F) Boiling point: 210°C (410°F) Flash point: 132°C (270°F) Specific gravity @ 20°C/20°C: 1.06 CAS: 126-30-7 Excellent thermal stability for low resin color Excellent weathering Good chemical, stain, and humidity resistance Good hardness and flexibility balance Rapid reaction during esterification and cure Used as a raw material in intermediate manufacturing and many coating applications.

POLYOX™ WSR 1105

POLYOX™ WSR 1105 is a polyethylene oxide thickener. It is a water-soluble resin with a viscosity of 8,800 to 17,600 cP.

POLYOX™ WSR 1105 has a molecular weight of 900,000 and has the highest viscosity in the POLYOX range. It is widely used as binder, lubricant, thickener and water retention aid. It forms flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Further it provides wet tack in paper products. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 8800- 17600 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity

POLYOX™ WSR 205

POLYOX™ WSR 205 is a water-soluble thickener with a molecular weight 600,000. The viscosity ranges from 4,500 to 8,800 cP.

POLYOX™ WSR 205 is a polyethylene oxide with a viscosity of 4500 - 8800 cP. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 6800 - 8800 cP pH at 25degC: 8.0 - 10.0 Loss on drying: 0.0 - 1.0 WT% Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR 301

POLYOX™ WSR 301 is a water-soluble resin with a high molecular weight of 4,000,000.

POLYOX™ WSR 301 is a polyethylene oxide (PEO) with a viscosity of 1650 - 5500 cP. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Further it provides wet tack in paper products. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper, adhesives, building and construction. In Concrete, It works as a flow aid in pumped, lightweight, spray and underwater concrete. Viscosity: 1650 - 5500 cP pH at 25degC: 8.0 - 10.0 Loss on drying: 0.0 - 1.0 WT% Silicon dioxide: 0.8 - 3.0 WT% High binding efficiency Crosslinkable Viscoelastic Flow and pumpability aid Lubrication aid Thermoplastic Low toxicity Nonionic

POLYOX™ WSR 301 Fine Powder NF

POLYOX™ WSR 301 Fine Powder NF has same characteristic as POLYOX™ WSR 301, except this grade is pharma compliant.

POLYOX™ WSR 301 is a polyethylene oxide with a viscosity of 1650 - 5500 cP. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 1650 - 5500 cP pH at 25degC: 8.0 - 10.0 Loss on drying: 0.0 - 1.0 WT% Silicon dioxide: 0.8 - 3.0 WT% National Formulary Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR 303

POLYOX™ WSR 303 has a molecular weight 7,000,000 and the viscosity ranges from 7,500 to 10,000 cP.

POLYOX™ is a polyethylene oxide thickener and water-soluble. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 7500 - 10000 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR 308

POLYOX™ WSR 308 is a polyethylene oxide thickener. It has a high molecular weight of 8,000,000 and a viscosity range of 10,000 to 15,000.

POLYOX™ is a water-soluble resin and used as binder, lubricant, thickener and water retention aid in various applications. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. POLYOX™ WSR 308 has the highest molecular weight of the POLYOX range. Viscosity: 10000 - 15000 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic Available in 140 lb and 960 lb drums

POLYOX™ WSR N10

POLYOX™ WSR N10 is a polyethylene oxide and water soluble thickener. It has a molecular weight of 100,000 and yields a viscosity of 12 to 50 at moderate addition levels.

POLYOX™ are water-soluble resins with a high molecular weight. They provide lubricity, binding, water retention, thickening and film forming properties. Main applications are in agriculture, adhesives, paper & pulp, industrial cleaners, ceramics and electronics. POLYOX™ WSR N10 has the lowest molecular weight of the POLYOX™ range and used where lower viscosity is required. It is a recommended grade for seed coatings. Viscosity: 30 - 50 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N10 100 Mesh

POLYOX™ WSR N10 100 Mesh has the same properties than POLYOX™ WSR N10 100, except this has finer particles.

POLYOX are water-soluble polyethylene oxide resins with a high molecular weight. They provide lubricity, binding, water retention, thickening and film forming properties. Main applications are in agriculture, adhesives, paper & pulp, industrial cleaners, ceramics and electronics. POLYOX™ WSR N10 mesh has the lowest molecular weight of the POLYOX range and used where lower viscosity is required. This mesh grade has a smaller particle size. Viscosity: 30 - 50 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N12K

POLYOX™ WSR N12K is a water-soluble polymer and has a molecular weight of 1,000,000. It yields a viscosity of 400 to 800 cP at 2% addition level.

POLYOX™ are water-soluble polyethylene oxide resins with a high molecular weights. They provide lubricity, binding, water retention, thickening and film forming properties. Main applications are in agriculture, adhesives, paper & pulp, industrial cleaners, ceramics and electronics. POLYOX™ WSR N12K has a relative low viscosity of 400-800 cP. Viscosity: 400 - 800 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N3000

POLYOX™ WSR N3000 is a water-soluble resin with a relative high molecular weight of 400,000. It yields a viscosity of 2,250 to 4,500 at moderate addition levels.

POLYOX™ WSR N3000 is typically used in fluorescent lamp phosphors or as phosphor binders in cathode ray tubes. POLYOX™ is a polyethylene oxide thickener and water-soluble. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 2,250 - 4,500 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N3000 LS

POLYOX™ WSR N3000 LS has the same characteristics as POLYOX™ WSR N3000, except LS version has a low silicon dioxide level of less than 1.5WT%.

POLYOX™ WSR N3000 is typically used in fluorescent lamp phosphors or as phosphor binders in cathode ray tubes. POLYOX™ is a polyethylene oxide thickener and water-soluble. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 2,250 - 4,500 cP Silicon dioxide: 0.0 - 1.5 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N60K

POLYOX™ WSR N60K is a PEO polymer with a molecular weight of 2,000,000.

POLYOX™ WSR 60K is a polyethylene oxide with a viscosity of 2000 - 4000 cP in a 2% aqueous solution. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 2000 - 4000 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N750

POLYOX™ WSR N750 is a water-soluble thickener with a molecular weight of 300,000. It has a viscosity range of 600 to 1,200 in a 5% solution.

POLYOX™ WSR N750 is widely used as seed coatings, wet-tack in paper adhesives, thickener in industrial cleaning products and coatings and paint removers for building and construction. In fluorescent lamp phosphors the N750 is used as binder. POLYOX™ is a polyethylene oxide thickener and water-soluble. Is functions as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Viscosity: 600 - 1,200 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N80

POLYOX™ WSR N80 is a water-soluble PEO thickener with a molecular weight of 200,000. It has a low viscosity of 65 to 115 cP.

POLYOX™ are water-soluble polyethylene oxide resins with a high molecular weights. They provide lubricity, binding, water retention, thickening and film forming properties. Main applications are in agriculture, adhesives, paper & pulp, industrial cleaners, ceramics and electronics. POLYOX™ WSR N80 is one of the lower molecular weight grades of the POLYOX™ range. Viscosity: 65 - 115 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

Regular, Powder

Manufactured using the fusion process. The regular grade is often used for general purposes & ceramics.

Calcium stearate is a carboxylate which is formed from stearic acid and calcium oxide. Its primary uses are as a flow agent, stabilizer, thicker, and surface conditioner. Appearance: white powder Melting Point: 160 °C Insoluble in H2O Great tin uses such as thin fibers and films. Does not melt , but will reach plastic phase at a normal processing temperature. Great catalyst/neutralizer.

ROCIMA™ 63

A thin-film fungicide and algaecide based on carbendazim, diuron and octylisothiazolinone chemistries. 

DuPont industrial microbicides are a collection of in-can and thin film preservatives that are appropriate for a multitude of product applications. Physical state: paste Color: White to gray Odor: Mild odor pH: 8.1 Vapor Pressure: 17.50 mmHg at 20°C (68°F) Relative Density (water = 1): 1.1 Flowable / pumpable Cost effective Low VOC formulation Paints & Coatings

ROZONE™ 2000

This dichloro-octylisothiazolinone (DCOIT) based thin-film fungicide and mildewcide suitable for solvent based products.

DuPont Industrial microbicides are a collection of in-can and thin-film preservatives that are appropriate for a multitude of product applications. Physical state: liquid clear Color: green Odor: Mild odor pH: 2.8 Aqueous solution Boiling point: (760 mmHg) 243°C ( 469°F) Solvent Flash point: 116°C ( 240°F) Low leaching Non-yellowing Cost effective Low water solubility Stains preservative, solvent based preservative, coating preservative, adhesive preservative, caulks, sealants, stucco, grout

Sodium PYRION™ 40%

Antimicrobial preservative (sodium pyrithione) used in a variety of water-based functional fluids and coatings to protect against micro-organisms.

Sodium Pyrion is highly effective against micro-organisms. Often used in water based fluids such as metal working, hydraulic, industrial lubricants, and water based latex paint applications. The pyrithione chemistry is often used when stability and low leachability is critical. Able to be used in low doses, reduces treatment costs and can be used in post treatment or metalworking fluid concentrates. Appearance: Clear, yellow-brown liquid Specific Density: 1.10 - 1.24 g/ml pH-value : 1.19 - 1.24 g/ml Molecular weight: 149.15 Thermal stability: 250°C CAS number: 3811-73-2 EPA registered Low treat rates Non-leaching results with long term protection Ease of application in aqueous form Due to the effectiveness at low treat rates, Sodium Pyrion saves formulators time and money by gaining more antimicrobial effectiveness, while using less.

Solus™ 2100

Solus™ 2100 is a performance additive for alkyd systems. It improves dry time and hardness development while maintaining the chemical resistance in coatings.

Solus™ 2100 is a performance additive designed for high-solids solvent-borne systems. Solus™ enables formulators to develop VOC-compliant coatings while reaching high performance. It provides faster dry time and reduces contamination on the coating's surface resulting in more efficiency. It has benefits in 2K-PU, UV resins, and acrylic lacquers. Faster dry-to-touch time Excellent anti-sag behavior Wider window of polishability Improved gloss after polishing Ease of sanding

Solus™ 2300

Solus™ 2300 is similar to Solus™ 2100 except it has a higher glass transition temperature.

Solus™ 2300 is a performance additive designed for high-solids solvent-borne systems. Solus™ enables formulators to develop VOC-compliant coatings while reaching high performance. It provides faster dry time and reduces contamination on the coating's surface resulting in more efficiency. It has benefits in 2K-PU, UV resins, and acrylic lacquers. Faster dry-to-touch time Excellent anti-sag behavior Wider window of polishability Improved gloss after polishing Ease of sanding

TBAA (Dimethylethyl Oxobutanoate)

Reagent used in coatings utilizing polyesters, acrylics, cellulosics, and epoxies.

Eastman™ TBAA (T-Butyl-Acetoacetate) provides room temperature cure and isocyanate-free crosslinking in many coating applications. It can also be used as a reagent in pharmaceuitical, agrichemical, and pigment applications. Appearance: Liquid Molecular weight: 158.20 Flash point: 66°C (151°F) Boiling point: 190°C (374°F) Specific gravity @ 20°C/20°C: 0.954 CAS: 1694-31-1 Increased adhesion to metal substrates Low glass transition resulting in increased coating flexibility Reacts with conventional crosslinkers Reduces viscosity in resins to meet lower VOC emissions Used in adhesives, sealants, architectural coatings, paints, coatings, and intermediate manufacturing in pharmaceuiticals and agriculture.

TICO® ORANGE 640

TICO® Orange 640 is a hybrid medium orange pigment.

Tico® is a titanium based yellow, orange and red pigment preperation. These products have excellent gloss, opacity, strength and durability. Appearance: Orange Powder Density (g/cm3): 2.6 Bulk Volume (g/cm3): 0.48 Oil Absorption (ml/100g): 19 Specific Surface (BED) (m2/g): 2.7 pH: 6 - 8 Reduced dusting Specially micronized Pre-dispersed organic colorant UV-absorbers Highly opaque

TICO® RED 642

TICO® Red 642 is a hybrid yellow shade red pigment.

Tico® is a titanium based yellow, orange and red pigment preparation. These products have excellent gloss, opacity, strength and durability. Appearance: Red Powder Density (g/cm3): 2.3 Bulk Volume (g/cm3): 0.3 Oil Absorption (ml/100g): 20 Specific Surface (BED) (m2/g): 8.7 pH: 7 - 9 Reduced dusting Specially micronized Pre-dispersed organic colorant UV-absorbers Highly opaque

TICO® RED 655

TICO® Red 655 is a hybrid medium shade red red.

Tico® is a titanium based yellow, orange and red pigment preperation. These products have excellent gloss, opacity, strength and durability. Appearance: Red Powder Density (g/cm3): 2.7 Bulk Volume (g/cm3): 0.33 Oil Absorption (ml/100g): 21 Specific Surface (BED) (m2/g): 9 pH: 6 - 8 Reduced dusting Specially micronized Pre-dispersed organic colorant UV-absorbers Highly opaque

TICO® YELLOW 588

TICO® Yellow 588 is a hybrid green shade yellow pigment.

Tico® is a titanium based yellow, orange and red pigment preparation. These products have excellent gloss, opacity, strength and durability. Appearance: Yellow Powder Density (g/cm3): 3.5 Bulk Volume (g/cm3): 0.5 Oil Absorption (ml/100g): 15 Specific Surface (BED) (m2/g): 6.1 pH: 6 - 8 Reduced dusting Specially micronized Pre-dispersed organic colorant UV-absorbers Highly opaque

TICO® YELLOW 594

TICO® Yellow 594 hybrid medium shade yellow pigment.

Tico® is a titanium based yellow, orange and red pigment preparation. These products have excellent gloss, opacity, strength and durability. Appearance: Orange Powder Density (g/cm3): 2.6 Bulk Volume (g/cm3): 0.48 Oil Absorption (ml/100g): 19 Specific Surface (BED) (m2/g): 2.7 pH: 6 - 8 Reduced dusting Specially micronized Pre-dispersed organic colorant UV-absorbers Highly opaque

TICO® YELLOW 622

TICO® Yellow 622 is a hybrid bright red shade yellow pigment.

Tico® is a titanium based yellow, orange and red pigment preparation. These products have excellent gloss, opacity, strength and durability. Appearance: Yellow Powder Density (g/cm3): 3.1 Bulk Volume (g/cm3): 0.29 Oil Absorption (ml/100g): 20 Specific Surface (BED) (m2/g): 6.6 pH: 6 - 8 Reduced dusting Specially micronized Pre-dispersed organic colorant UV-absorbers Highly opaque

TMPD Molten

Melted to form a clear, clean liquid for easier handling. This is also available in solid form platelets at room temperature.

Eastman TMPD™ molten is a liquid glycol used to formulate coatings and unsaturated polyester laminating resins. TMPD™ is ideal for formulating high solids and low VOC coatings. Appearance (molten): Clear, clean liquid Molecular weight: 146.22 Melting point: 46-55°C (114.8-131°F) Crystallization point: 31°C (88°F) Flash point: 113°C (235°F) Boiling point @ 760 mm Hg: 220-235°C (428-455°F) Specific gravity @ 55°C/15°C: 0.928 CAS: 144-19-4 Very stable in waterborne polyester formulations Excellent chemical, stain, and humidity resistance Low viscosity and density allowing excellent solubility in solvents Outstanding corrosion resistance in fiberglass-reinforced plastic applications Used in coatings for metal office furniture, automotive, industrial maintenance, and general metal applications.

TMPD Platelets

Solid, white irregularly shaped platelets at room temperature. Also available in molten form for easier handling when heated to 115°F.

Eastman TMPD™ platelets is a white, waxy solid used to formulate coatings and unsaturated polyester laminating resins. TMPD™ is ideal for formulating high solids and low VOC coatings. Appearance (molten): Clear, clean liquid Molecular weight: 146.22 Melting point: 46-55°C (114.8-131°F) Crystallization point: 31°C (88°F) Flash point: 113°C (235°F) Boiling point @ 760 mm Hg: 220-235°C (428-455°F) Specific gravity @ 55°C/15°C: 0.928 CAS: 144-19-4 Very stable in waterborne polyester formulations Excellent chemical, stain, and humidity resistance Low viscosity and density allowing excellent solubility in solvents Outstanding corrosion resistance in fiberglass-reinforced plastic applications Used to formulate liquid coatings for metal office furniture, automotive, industrial maintenance, and general metal applications. Other applications include detergent additive, hard surface cleaner, plasticizer intermediate, and synthetic lubricants.

Trilene® 65

Low molecular weight liquid Ethylene Propylene (EPDM) terpolymer with 10% diene content for use in rubber, coatings and adhesives.

Trilene® 65 is a liquid EPDM terpolymer that is used as an additive in rubber compounds and works well in peroxide-cured systems to reduce viscosity. It acts as a reactive plasticizer in rubber compounds without any significant loss of hardness or other mechanical properties. In coatings & adhesives Trilene® 65 is used as a nonpolar, non crystalline elastomeric material that provides strong adhesion to a variety of substrates. Additionally, Trilene® 65 demonstrates low permeability to gases and water vapor, superior impact resistance and high flexibility at low temperatures. Ethylene/Propylene: 50/50 Degree of Unsaturation (% Diene): 10% Type of Diene: DCPD Color: Pale Yellow Specific Gravity: 0.86 Molecular Weight by GPC (Da): 47,000 Brookfield Viscosity (cP, RVT #7 at 60°: 1,900,000 Brookfield Viscosity (cP, RVT #7 at 100°: 177,000 Volatiles at 100ºC (212ºF): <0.5% Easy to process Non extractable Maintains mechanical properties Non-volatile Hydrophobic with low surface energy Compatible with other polymers, oils and solvents Flexible at low temperatures Excellent resistance to moisture, UV light, ozone and chemical degradation Adhesion to various substrates without the use of a primer Good impact resistance Rubber belts and hoses for Aerospace and Automotive Building & Construction Wire & Cable Weather stripping Conveyer belts Roof coatings Elastomeric coatings Marine coatings Anticorrosion coatings Barrier coatings that need permeability to air, water and chemicals Elastomeric sealants & adhesives

Trilene® 67

Low molecular weight liquid Ethylene Propylene (EPDM) terpolymer with 9.5% diene content for use in rubber, coatings and adhesives.

Trilene® 67 is a liquid EPDM terpolymer that is used as an additive in rubber compounds and works well in sulfur-cured systems to reduce viscosity. It acts as a reactive plasticizer in rubber compounds without any significant loss of hardness or other mechanical properties. In coatings & adhesives Trilene® 67 is used as a nonpolar, non crystalline elastomeric material that provides strong adhesion to a variety of substrates. Additionally, Trilene® 67 demonstrates low permeability to gases and water vapor, superior impact resistance and high flexibility at low temperatures. Ethylene/Propylene: 46/54 Degree of Unsaturation (% Diene): 9.5% Type of Diene: ENB Color: Pale Yellow Specific Gravity: 0.86 Molecular Weight by GPC (Da): 39,000 Brookfield Viscosity (cP, RVT #7 at 60°: 900,000 Brookfield Viscosity (cP, RVT #7 at 100°: 128,000 Volatiles at 100ºC (212ºF): <0.5% Easy to process Non extractable Maintains mechanical properties Non-volatile Hydrophobic with low surface energy Compatible with other polymers, oils and solvents Flexible at low temperatures Excellent resistance to moisture, UV light, ozone and chemical degradation Adhesion to various substrates without the use of a primer Good impact resistance Rubber belts and hoses for Aerospace and Automotive Building & Construction Wire & Cable Weather stripping Conveyer belts Roof coatings Elastomeric coatings Marine coatings Anti-corrosion coatings Barrier coatings that need permeability to air, water and chemicals Elastomeric sealants & adhesives

Trilene® 77

Low molecular weight Ethylene Propylene (EPDM) terpolymer with 10.5% diene content for use in rubber, coatings and adhesives.

Trilene® 77 is a crystalline waxy EPDM terpolymer that is used as an additive in rubber compounds and works well in sulfur-cured systems to reduce viscosity. It acts as a reactive plasticizer in rubber compounds without any significant loss of hardness or other mechanical properties. In coatings & adhesives Trilene® 77 is used as a nonpolar, non crystalline elastomeric material that provides strong adhesion to a variety of substrates. Additionally, Trilene® 77 demonstrates low permeability to gases and water vapor, superior impact resistance and high flexibility at low temperatures. Trilene® 77 is easier to handle during mixing compared to Trilene® 65 and 67 since it is a solid at room temperature. Ethylene/Propylene: 74/26 Degree of Unsaturation (% Diene): 10.5% Type of Diene: ENB Color: Pale Yellow, Waxy solid Specific Gravity: 0.86 Molecular Weight by GPC (Da): 27,000 Brookfield Viscosity (cP, RVT #7 at 60°: 800,000 Brookfield Viscosity (cP, RVT #7 at 100°: 102,000 Volatiles at 100ºC (212ºF): <0.5% Easy to process East to weigh before mixing Non extractable Maintains mechanical properties Non-volatile Hydrophobic with low surface energy Compatible with other polymers, oils and solvents Flexible at low temperatures Excellent resistance to moisture, UV light, ozone and chemical degradation Adhesion to various substrates without the use of a primer Good impact resistance Rubber belts and hoses for Aerospace and Automotive Building & Construction Wire & Cable Weather stripping Conveyer belts Roof coatings Elastomeric coatings Marine coatings Anti-corrosion coatings Barrier coatings that need permeability to air, water and chemicals Elastomeric sealants & adhesives

Tyzor® 212, zirconium chelate

A water stable zirconium chelate with ca. 52% active ingredient in 1-propanol solution.

Tyzor 212 is a clear, slightly viscous yellow liquid with 52% active ingredient which is stable in water for extended periods. It reacts with water by hydrolysis to form a reactive hydroxy zirconium chelate which can form bonds with organic -OH and -COOH groups of many polymeric carbohydrates such as cellulose, guar derivatives and starch. Strong gels can be formed by crosslinking. Tyzor 212 can also act as an adhesion promoter to -OH functional surfaces. Zr Content: 12% Active Content: 52% Color: Yellow Solvent: n-propanol Specific Gravity (25C): 1.06 Freezing Point: <-25C Boiling Point: 97C (Solvent) Flash Point: 22C Solubility in Solvents: Miscible in most organic solvents Solubility in Water: Miscible In oil well fracturing fluids, Tyzor 212 can be used in pH 8.5-11 fluids and acts as a delayed crosslinking agent that initiates above 49C (120F). It's an effective crosslinker for dispersions of guar and it's derivatives to form high viscosity aqueous gels. For coatings, inks and paints applications, see increased film strength, adhesion promotion and rheology control. Due to it's great water compatibility and low color generation, Tyzor 212 also functions well over a wide range of pH.

Tyzor® 217, zirconium lactate

A water based zirconium chelate with pH around 7 stable in water.

Suitable for crosslinking carbohydrates such as cellulose, starch, guar and other functionalized polymers like polyvinyl alcohol. Tyzor 217 also functions as a surface modifier and adhesion promoter on paper, glass, metal, pigments and other materials with oxidized surfaces. Zr Content: 5.4% Color: Pale Yellow Solvent: Water Specific Gravity (25C): 1.2 g/mL Freezing Point: 0C Boiling Point: 100C Flash Point: None Solubility in Water: Fully Miscible No Voc Content Low toxicity Cross-linking agent for dispersions of guar to form high viscosity aqueous gels used in oil well fracturing applications Cross links pigements and binders in waterborne paints and printing inks Adhesion promoter in metal, glass, fillers and pigments to increase compatibility and modify physical properties Modifies surface of paper and sysnthetic nonwovens to increase hardness and decrease hydrophilicity

Tyzor® 9000

Tyzor™ 9000 is a colorless to yellowish reactive organic alkoxy titanate liquid with a 100% active content.

Tyzor 9000 improved crosslinking of polymers, adhesion promotion and the formation of polymeric titanium dioxide layers as binders or coatings. It can also act as a Lewis acid catalyst in applications such as condensation, esterification, transesterification and addition reactions. TiO2 Content: 23.9% Active Content: 100% Molecular Weight: 340 g/mol Color: Yellow Specific Gravity (25C): 0.9 Viscosity (25C): 140 mPa*s Pour Point: -40C Boiling Point: >100C (Decomposes) Flash Point: 60C Refractive Index: 1.444 Solubility in Solvents: Miscible in most organic solvents Solubility in Water: Decomposes Quickly In Coatings Improved surface hardness, coloring effects, corrosion protection and heat and light reflection, corrosion resistance and adhesion in coating applications In Crosslinking Crosslinks with polymers or binders containing -OH and -COOH functional groups. In Pigments and Films Can be used to Micro or nano scale TiO2 pigments used to create polymeric TiO2 films on surfaces via pyrolytic or hydrolytic processes In Reaction catalysts Elimination of by products, increased yield, easy work up, low catalyst concentration and low toxicity

Tyzor® AA, titanium acetylacetonates

A liquid titanium chelate with acetylacetonate as the chelating agent. It is moderately stable in water for short periods of time.

Tyzor AA is typically used for adhesion promotion, but also frequently used for crosslinking in non-aqueous systems, catalysis and surface modification. They are soluble and or miscible in organic solvents or products like ethanol, isopropanol, butanol, ethyl acetate, IPA, methyl ethyl ketone and acetone. TiO2 %: 16.5 Active Content %: 75 Form: Liquid Color: Yellow to Red Solvent: 25% IPA Specific Gravity: 0.99 Viscosity, mPa: 10 Pour Point C(F): 0(32) Boiling Point C(F) Solvent: 82(179.6) Flash Point C(F): 12(53.6) Solubility: Miscible in most organic solvents. Decomposes in water Improved drying, solvent resistance, heat resistance adhesion to substrates such as aluminum and polyolefin foils in printing applications. Elimination of by products, high yield and easy work up in esterification and transesterification under mild conditions. Improved surface hardness, dispersibility, coloring effects, corrosion protection and heat and light reflection in coating applications. When combined with metal alkoxides, produce metal oxide systems for use as binders or coatings

Tyzor® AA-105

A titanium chelate with acetylacetonate as the chelating agent with an 100% active content.

Tyzor AA-105 is similar to Tyzor AA, but has a TiO2 and active content of 23% and 100% respectively with no solvent content. TiO2 %: 23 Active Content %: 100 Form: Liquid Color: Yellow to Red Solvent: None Specific Gravity: 1.12 Viscosity, mPa: 90 Pour Point C(F): -25(-13) Boiling Point C(F) Solvent: n/a Flash Point C(F): 50(122) Solubility: Miscible in most organic solvents. Decomposes in water See benefits from Tyzor AA

Tyzor® AA-65, titanium acetylacetonates

A titanium chelate with acetylacetonate as the chelating agent. It is moderately stable in water and with a pour point of -70°C.

Tyzor AA-65 is similar to Tyzor AA, but has a TiO2 and active content of 15% and 65% respectively. It has a solvent content of 28% IPA and 7% EtOH TiO2 %: 15 Active Content %: 65 Form: Liquid Color: Yellow to Red Solvent: 28% IPA/7% EtOH Specific Gravity: 0.98 Viscosity, mPa: 8 Pour Point C(F): -70(-94) Boiling Point C(F) Solvent: 78(172.4)[Ethanol] Flash Point C(F): 14(57.2) Solubility: Miscible in most organic solvents. Decomposes in water See benefits from Tyzor AA

Tyzor® AA-75, titanium acetylacetonates

A titanium chelate with acetylacetonate as the chelating agent. It is moderately stable in water and with a pour point of -5°C.

Tyzor AA-75 is similar to Tyzor AA, but with specific gravity of 1.02 and viscosity 11 mPa. TiO2 %: 16.5 Active Content %: 75 Form: Liquid Color: Yellow to Red Solvent: 25% IPA Specific Gravity: 1.02 Viscosity, mPa: 11 Pour Point C(F): -5(23) Boiling Point C(F) Solvent: 82(179.6) Flash Point C(F): 12(53.6) Solubility: Miscible in most organic solvents. Decomposes in water Improved drying, solvent resistance, heat resistance adhesion to substrates such as aluminum and polyolefin foils in printing applications. Elimination of by products, high yield and easy work up in esterification and transesterification under mild conditions. Improved surface hardness, dispersibility, coloring effects, corrosion protection and heat and light reflection in coating applications. When combined with metal alkoxides, produce metal oxide systems for use as binders or coatings.

Tyzor® BTM

Tyzor™ BTM is similar to Tyzor 9000, but with a viscosity of 65 cp and a boiling point of 246°C.

See Tyzor 9000. Can also be used in polymerization reactions. TiO2 Content: 14% Active Content: 100% Molecular Weight: 340 g/mol Color: Yellow Specific Gravity (25C): 0.99 Viscosity (25C): 65 cp Pour Point: -70C Boiling Point: 246C Flash Point: 47C Refractive Index: 1.493 Solubility in Solvents: Miscible in most organic solvents Solubility in Water: Decomposes Quickly See Tyzor 9000. Also a useful catalyst in Ziegler-Natta reactions in the synthesis of polyolefins.

Tyzor® BTP, n-Butyl polytitanate

A yellowish polymeric butyl titanate with a 100 % active content.

Tyzor BTP is an organic liquid sensitive to moisture and has a very high TiO2 content with a low VOC amount in comparison to other titanates and zirconates TiO2 Content: 34.5 % Active Content: 100 % Color: Yellow Density (25C): 1.12g/cm3 Viscosity (25C): 2,000-6,000 mPa*s Pour Point: -39C Boiling Point: 246C Solubility in Solvents: Miscible in most organic solvents Solubility in Water: Decomposes quickly Solubility in Solvents: Miscible in most organic solvents In Reaction catalysts Elimination of by products, increased yield, easy work up, low catalyst concentration and low toxicity In Coatings Improved surface hardness, coloring effects, corrosion protection and heat and light reflection, iridescence, corrosion resistance, scratch resistance and adhesion in coating applications In Paint Additives BTP can be used as an additive to crosslink -OH and -COOH functional polymers, act as a binder itself or promote adhesion. In Pigments and Films Can be used to Micro or nano scale TiO2 pigments used to create polymeric TiO2 films on surfaces via pyrolytic or hydrolytic processes Binder Tyzor BTP can act as an inorganic binder by itself or combined with metal oxides in mineral filled systems to provide high temperature resistance.

Tyzor® EHTAA

Tyzor EHTAA is a titanium chelate with acetylacetonate as a chelating agent and 66% active content in 2-ethylhexanol.

EHTAA is a clear amber to orange slightly viscous liquid soluble in water for a short period of time. It can improve adhesion promotion, crosslinking of functional polymers or used to form polymeric titanium dioxide layers as a binder or coating. It can also act as a Lewis acid catalyst in Transesterification, esterification, condensation and addition reactions. They can also be used as additives in paint to crosslink functional polymers to binders, promote adhesion or bind to itself TiO2: 10.6% Ti Content: 6.3% Active Content: 66% Color: Yellow to Amber Solvent: 2-Ethylhexanol Specific Gravity (25C): 0.94 g/mL Boiling Point: 185C (Solvent) Flash Point: 54C Solubility in Solvents: Miscible in most organic solvents Solubility in Water: Partly Miscible In Coatings Improved surface hardness, coloring effects, corrosion protection and heat and light reflection, corrosion resistance and adhesion in coating applications In Pigments and Films Can be used to Micro or nano scale TiO2 pigments used to create polymeric TiO2 films on surfaces via pyrolytic or hydrolytic In Reaction catalysts Elimination of by products, increased yield, easy work up, low catalyst concentration and low toxicity In Printing inks See improved drying rates, increased solvent resistance, heat resistance, adhesion and crosslinking to various substrates in solvent based printing inks

Tyzor® GBA, titanium acetylacetonates

A titanium chelate with acetylacetonate as the chelating agent with a 16.4% TiO2 content.

Tyzor GBA can be applied as a coating primer, additive or in sol-gel systems as a base material. It can also act as a Lewis acid catalyst in esterification, transesterification, condensation and addition reactions. TiO2 %: 16.4 Active Content %: 75 Color: Orange to Red Solvent: Isopropanol, Butanol, Methanol Specific Gravity: 1.02 Viscosity, cps: 60 Pour Point C: -42 Boiling Point C: 70 Flash Point C: 12 Solubility in solvents: Miscible in most organic solvents Solubility: Decompose Excellent crosslinker and adhesion promoter in solvent based inks. Additional benefits in inks include improved dry rates, adhesion, solvent and heat resistance. In coating applications, glass, metals, fillers and pigments can be treated with Tyzor GBA to give increased adhesion promotion, surface hardness, scratch resistance, heat and light reflection and corrosion resistance. Act as additives to aid in crosslinking -OH and -COOH functional polymers or binders. Tyzor GBA also eliminate by products, increase yield, easy work-up and low catalyst concentration in esterification and transesterification of various esters and polyesters. These benefits also extend to addition reactions for polyurethanes

Tyzor® GBO, titanium acetylacetonates

A titanium chelate with acetylacetonate as the chelating agent with a 12.7% TiO2 content.

Similar to Tyzor GBA TiO2 %: 12.7 Active Content %: 60 Color: Orange to Red Solvent: Isopropanol, Butanol, Methanol Specific Gravity: 0.95 Viscosity, cps: <10 Pour Point C: <-42 Boiling Point C: 70 Flash Point C: 12 Solubility in solvents: Miscible in most organic solvents Solubility: Decompose Similar to Tyzor GBA

Tyzor® LA, titanium chelate

A stable water based titanium chelate excellent for use in aqueous systems. Tyzor LA is stable at pH around 7-8.

Tyzor LA can be used as a catalyst in transesterification, esterification and condensation applications. It can also be used as a cross linking agent for OH functional polymers, adhesion promoter and aid in the formation of polymeric titanium dioxide as a binder or coating. TiO2 Content: ca. 13.6% Active Content: ca. 50% Color: Colorless to light Density (25C): ca. 1.21/ml Viscosity (25C): ca.9 mPa*s pH: ca. 8-9 Pour Point: ca. -10C Boiling Point: ca. 100 (water) C Flash Point: None Solubility in Water: Miscible

Tyzor® NBZ, zirconium tetra-n-butanolate

Tyzor NBZ is a yellowish, highly reactive organic alkoxy zirconate with 87% active content in n-butanol.

Tyzor NBZ is used as a Lewis acid catalyst for esterification, addition and condensation reactions. They can also be used as Ziegler-Natta catalysts for polymerization. Some benefits include elimination of by products, increased yield, easy work up, low catalyst concentration and low toxicity ZrO2 Content: 28 % Active Content: 87 % Color: Yellow Molecular Weight: 383 g/mol Density (20C): 1.07 g/mL Viscosity (20C): 100 mPa*s Pour Point: -70 C Boiling Point (@10 mmHg): 117 C (Solvent) Flash Point: 35 Refractive Index: 1.51 Solubility in Solvents: Miscible in most organic solvents Solubility in Water: Decomposes quickly In Reaction catalysts Effective in reactions such as esterification, transesterification, condensation and addition reactions to result in products like acrylic esters, polyesters and plasticizers. Benefits include elimination of by products, increased yield, easy work up, low catalyst concentration and low toxicity In Coatings Improved surface hardness, coloring effects, corrosion protection and heat and light reflection, iridescence, corrosion resistance, scratch resistance and adhesion in coating applications In Paint Additives NBZ can be used as an additive to crosslink -OH and -COOH functional polymers, act as a binder or promote adhesion. In Pigments and Films Can be used to Micro or nano scale ZrO2 pigments used to create polymeric ZrO2 films on surfaces via pyrolytic or hydrolytic processes

Tyzor® PITA SM

Tyzor™ PITA SM is a mixture of titanium ethyl acetoacetate complex with 100% active content and methyl-trimethoxy silane.

Tyzor PITA-SM is designed as a curing agent for silicone based sealants and adhesives. Its high reactivity at low temperatures enables it to react with common functional groups such as R-OH, M-OH, SiOH, or R-COOH to effect cure rate, crosslinking and adhesion promotion. TiO2 Content: ca. 15.2% Active Content: ca. 80% Color: Yellow to Orange Density (20 C): ca. 1.08 g/ml Viscosity (20 C): ca. 8 mPa*s Pour Point: < -10 C Boiling Point: ca. 102 C (Solvent) Flash Point: ca. 32 C Solubility in Solvents: Miscible in most organic solvents Solubility in water: Decomposes Tyzor PITA-SM in silicone sealants and adhesives promotes adhesion, crosslinks silanes, increases cure rate and acts as a drying agent. It can also provide these benefits when used with silanol end-capped polymers such as polypropylene oxides, acrylates, or polyurethanes. They can also be used as additives in paints to cross-link functional polymers or binders, act as binders or promote adhesion.

Tyzor® TE, triethanolamine Titanate

A triethanolamine titanium complex with 80% active ingredient in alcohol solvent. It hydrolyzes to form a water stable chelate.

Tyzor TE forms a reactive hydroxy titanium chelate by hydrolysis with water. This chelate is stable in water for extended periods. When crosslinked with polymers such as carbohydrates, strong gels can be formed. Tyzor TE can act as adhesion promoters to oxidized surfaces. They can also be used as Lewis acid catalysts in processes such as esterification, transesterification, condensation and addition reactions. TiO2 Content: ~13.7% Active Content: 80% Color: Light Yellow Density (25 C): 1.06 g/ml Viscosity (25 C): 350 mPa*s Pour Point: -47 C Boiling Point: 85 C Flash Point: 16 C In esterification, transesterification, condensation and addition reactions, expect moderate reaction rates, high yield, easy work-up, low toxicity and low catalyst concentration. It's an effective crosslinking agent for pigments and binders in waterborne paints, carbohydrate coated latex particles for viscous thixotropic paints and dispersions of guar and its derivatives to form highly viscous aqueous gels used in oil well fracturing.

Tyzor® TnBT, tetra-n-butyl titanate

A Lewis acid catalyst and highly reactive organic alkoxy titanate with 100% active content.

Excellent as cross-linking agent or effective adhesion promoter to polymers. Also forms polymeric titanium dioxide layers used as a binder or coating. Tyzor TnBT can be used as a Lewis acid catalyst in esterification, transesterification, condensation and addition reactions. TiO2 Content: 23.5 % Active Content: 100 % Color: Colorless to Pale Yellow Molecular Weight: 340 g/mol Density (20C): 0.99g/mL Freezing Point: -70C Boiling Point (@10 mmHg): 183C Flash Point: 47C Solubility in Solvents: Miscible in most organic solvents Solubility in Water: Decomposes quickly In Reaction catalysts Elimination of by products, increased yield, easy work up, low catalyst concentration and low toxicity In Coatings Improved surface hardness, coloring effects, corrosion protection and heat and light reflection, iridescence, corrosion resistance, scratch resistance and adhesion in coating applications In Paint Additives TnBT can be used as an additive to crosslink -OH and -COOH functional polymers, act as a binder itself or promote adhesion. In Pigments and Films Can be used to Micro or nano scale TiO2 pigments used to create polymeric TiO2 films on surfaces via pyrolytic or hydrolytic processes

Tyzor® TOT, tetra-2-ethylhexyl titanate

A clear to yellowish reactive organic alkoxy titanate with 100% active content, but less sensitive to moisture than TPT or TnBT

Similar to Tyzor TnBT TiO2 Content: 14.4 % Active Content: 100 % Color: Colorless to Pale Yellow Molecular Weight: 564 g/mol Density (20C): 0.92g/mL Viscosity (20C): 140 mPa Boiling Point (@10 mmHg): 249C Flash Point: 60C Refractive Index: 1.482 Solubility in Solvents: Miscible in most organic solvents Solubility in Water: Decomposes quickly Similar to Tyzor TnBT

VANADUR® PLUS YELLOW 9010 (P)

VANADUR® PLUS YELLOW 9010 is an inorganic Pigment Yellow 184 specifically designed for the plastics industry.

Vanadur®Plus pigments are a line of inorganic pigments based on bismuth vanadate. Often seen in automotive and industrial coatings due to their outstanding characteristics. Appearance: Yellow Powder Density (g/cm3): ~3.9 Bulk Density (g/cm3): ~0.3 Tamped Density (g/cm3): ~0.5 Oil Absorption (ml/100g): ~40 Water Soluble Salts (%): <0.5 pH: 8 - 9 Easy to disperse High color saturation Excellent opacity High-performance for plastics Silica encapsulated Extreme heat resistance Improved acid, alkali, and SO2 resistance

VYNAMON™ GREEN 6Y FW-C

VYNAMON™ GREEN 6Y is an organic Pigment Green 36.

Vynamon organic pigments are specifically engineered for plastics and powder coating. These pigments are of the highest quality therefore can be utilized in food packaging and toys. Appearance: Green Powder Density (g/cm3): 2.8 Bulk Volume (l/kg): 1.5 Specific Surface (m2/g): 50 Heavy metal free No chromates No sacrificial metals Heat stability in high temperature application

VYNAMON™ RED 312202

VYNAMON™ RED 312202 is an organic Pigment Red 122.

Vynamon organic pigments are specifically engineered for plastics and powder coating. These pigments are of the highest quality therefore can be utilized in food packaging and toys. Appearance: Red Powder Density (g/cm3): 1.4 Bulk Volume (l/kg): 6.3 Specific Surface (m2/g): 67 Heavy metal free No chromates No sacrificial metals Heat stability in high temperature application

VYNAMON™ YELLOW 118303

VYNAMON™ YELLOW 118303 is an organic Pigment Yellow 183.

Vynamon organic pigments are specifically engineered for plastics and powder coating. These pigments are of the highest quality therefore can be utilized in food packaging and toys. Appearance: Yellow Powder Density (g/cm3): 1.8 Bulk Volume (l/kg): 3.5 Specific Surface (m2/g): 22 Heavy metal free No chromates No sacrificial metals Heat stability in high temperature application

ZINC PHOSPHATE ZP 10

ZINC PHOSPHATE ZP 10 is specifically designed for applications requiring protective coatings.

HEUCOPHOS® products offer wide spectrum anti-corrosives, high-performance polyphosphates, and modified orthophosphates to provide the most optimal anti-corrosion coatings. Zinc as ZnO (%): 50.5 - 52.0 Phosphorous as P2O5 (%): 47 - 49 Loss on ignition 600°C (%): 8.5 - 13 Water-soluble chloride (%): max. 0.025 Water-soluble sulphate (%): max. 0.05 Conductivity (µS/cm): max. 150 pH: 6 - 8 Lead as Pb (ppm): max. 10 Cadmium as Cd (ppm): max. 10 Density (g/cm3): typ. 3.5 Bulk density, untamped (g/cm3): typ. 0.4 Bulk density, tamped (g/cm3): typ. 0.8 Oil absorption value (g/cm3): typ. 20 Sieve residue 32 microns (%): max. 0.01 Average particle size (microns): 2.0 - 3.5 Adjusted water soluble content Very narrow particle size distribution Excellent dispersibility Optimized particle structure

Zinc PYRION™ 48% MPF

Aqueous solution of zinc pyrithione with low water solubility and highly effective for applications where low level of leaching and longevity of protection is required.

Zinc Pyrion MPF 48% is a Micronized Preservative Free suspension of Zn-Pyrithione in water. This wide range & highly active biocide inhibits the unwanted growth of fungi, yeast, mold, and other microbial organisms. Appearance: Off-white suspension Density at 21⁰C/70⁰F: 1.28 g/cm3 (10.68 lb/gal) Viscosity at 21⁰C/70⁰F: 157.5 mPa.s at 100s-1 Color: L*: min. 75, a*: -3 to +1, b*: max. 5 Particle size: D100 ≤ 5 μm; D90 ≤ 1 μm pH, 5% w/w in pH 7 water: 6.5 – 9.0 Zinc content: 9.3 – 11.3 % w/w Must store above 10⁰C (50⁰F) Degradation occurs at temperatures above 240⁰C EPA registered Exceptional microbial control in a wide range of applications Ease of application in aqueous solution Testing available to gauge efficacy of antimicrobial growth for final product Zinc pyrithione is commonly used to prevent degradation caused by microbial growth in a wide range of industrial applications. Formulations will differ by composition, application and susceptibility of microbial attack. It is recommended to test biocide levels at multiple treat rates (3000, 4000, 5000 ppm) to gauge efficacy in particular applications. Industry standard laboratory testing is available from Janssen to help with particular formulation questions.

Zinc PYRION™ Powder

Powdered dry-film preservative (zinc pyrithione) that provides antimicrobial protection in a wide variety of industrial applications.

Zinc Pyrion is a Zinc Pyrithione based preservative for protection against unwanted microbial growth and degradation. The powdered dry-film preservative can be used in a wide range of both indoor & outdoor applications that are susceptible to microbial attack. Typical Properties; Appearance: Light beige to beige powder Purity (Potentiometric Titration): Min. 97.0 wt.% Loss on Drying (105°C): Max. 2 wt.% Particle Size Distribution: D50: max. 10 μm; D99: max. 35 μm Relative Density: 1.8106 at 22.5°C Bulk Density: 0.41 g/ml pH: 6.5 - 8.5 (5% dispersion in water) Vapor Pressure: < 6.6 x 10-4 Pa at 25°C Solubility in Water: 4.93 mg/l at 20.0°C; 6.11 mg/l at 30.0°C Exceptional control against microbial growth Cost effective powder form Full control of formulated treat rate Free testing available to measure efficacy of anti-microbial protection Typical treat rate will vary by application, but it is recommended to test several levels (2000, 3000, 4000, 5000 ppm) to test efficacy of protection. Testing is available via Janssen's laboratory for several industry standard tests.