Butyl Acrylate

Butyl acrylate (BA) is an acrylic acid ester with a sharp pungent odor. It is somewhat less dense than water and forms a slick surface on water.

Building blocks for polymer manufacturing and chemical manufacturing. Appearance: clear and colorless Physical Form: liquid Odor: pungent Molar Mass: 128.2 Assay (Gas chromatography) - min 99.5% Water Content (ASTM E 203) - max. 0.05% Acid Content (ASTM D 1613) - max. 0.01% Color on despatch (ASTM D 1209) - max. 10 Standard Stabilization (ASTM D 3125) 15+/- 5ppm MEHQ Forms copolymers and homopolymers Useful for feedstock synthesis Very slightly soluble in water

CELLOSIZE™ EP-09

CELLOSIZE™ EP-09 is a water-soluble cellulose thickener. It has the lowest viscosity of the CELLOSIZE™ product range of 90-160 cP. EP stands for emulsion polymerization grade.

CELLOSIZE is a hydroxylethyl cellulose polymer, nonionic and water-soluble. It is widely used as thickener, binder, emulsifier and film former. It holds moisture, suspends solids and has a good chemical compatibility. Key applications for CELLOSIZE include household cleaners, agriculture sprays, oil drilling or fracturing fluids, paper and inks, adhesives and textile back coatings. EP-09 is surface treated to increase dispersion in water. Viscosity: 90 to 160 cP Volatiles: 6 wt% Max Water insolubles: 0.07 wt% Max Particle size (through #20 mesh): 98% minimum Water-soluble Nonionic Protective colloid Effective film former Good chemical compatibility

CELLOSIZE™ QP-100MH

CELLOSIZE™ QP-100MH has the highest molecular weight of all CELLOSIZE products. This grade provides a high thickening efficiency.

CELLOSIZE is a hydroxylethyl cellulose polymer, nonionic and water-soluble. It is widely used as thickener, binder, emulsifier and film former. It holds moisture, suspends solids and has a good chemical compatibility. Key applications for CELLOSIZE include household cleaners, agriculture sprays, oil drilling or fracturing fluids, paper and inks, adhesives and textile back coatings. CELLOSIZE™ QP-100MH is widely used as thickener and yields a viscosity of 4,400 tp 6,000 cP. This grade provides the most pseudoplastic rheology and very effective where high thickening is desired. Viscosity: 4800 to 6000 cP Volatiles: 5 wt% Max Water insolubles: 1.50 wt% Max Particle size (through #20 mesh): 98% Min Water-soluble Nonionic Protective colloid Effective thickener Film former Good chemical compatibility

CELLOSIZE™ QP-15000H

CELLOSIZE™ QP-15000H is a cellulosic thickener with a medium molecular weight. As a general purpose thickener it is used in coatings, cleaners and adhesives.

CELLOSIZE™ QP-15000H EUR yields a viscosity of 1,100 to 1,500 cP. CELLOSIZE is a hydroxylethyl cellulose polymer, nonionic and water-soluble. It is widely used as thickener, binder, emulsifier and film former. It holds moisture, suspends solids and has a good chemical compatibility. Key applications for CELLOSIZE include household cleaners, agriculture sprays, oil drilling or fracturing fluids, paper and inks, adhesives and textile back coatings. Viscosity: 1,100 to 1,500 cP Volatiles: 5 wt% Max Water insolubles: 1.00 wt% Max Particle size (through #20 mesh): 98% Min Water-soluble Nonionic Protective colloid Effective film former Good chemical compatibility

CELLOSIZE™ QP-300

CELLOSIZE™ QP-300 is a hydroxylethyl cellulose (HEC) polymer with a medium viscosity of 300-400 cP. It can be used as a thickener and film former.

CELLOSIZE is a hydroxylethyl cellulose polymer, nonionic and water-soluble. It is widely used as thickener, binder, emulsifier and film former. It holds moisture, suspends solids and has a good chemical compatibility. Key applications for CELLOSIZE include household cleaners, agriculture sprays, oil drilling or fracturing fluids, paper and inks, adhesives and textile back coatings. Viscosity: 300 to 400 cP Volatiles: 5.0 wt% Max Water insolubles: 0.07 wt% Max Particle size (through #20 mesh): 98% minimum Water-soluble Nonionic Thickener Protective colloid Effective film former Good chemical compatibility

CELLOSIZE™ QP-30000H

CELLOSIZE™ QP-30000H is a general purpose thickener with a high molecular weight. It yields viscosity of 1,500-2,400 cP at low addition levels.

CELLOSIZE™ QP-30000H is a hydroxylethyl cellulose polymer, nonionic and water-soluble. It is widely used as thickener, binder, emulsifier and film former. It holds moisture, suspends solids and has a good chemical compatibility. Key applications for CELLOSIZE include household cleaners, agriculture sprays, oil drilling or fracturing fluids, paper and inks, adhesives and textile back coatings. CELLOSIZE™ QP-30000H has a medium molecular weight. Viscosity: 1,500 to 2,400 cP Volatiles: 6 wt% Max Water insolubles: 1.00 wt% Max Particle size (through #20 mesh): 98% Min Water-soluble Nonionic Protective colloid Effective film former Good chemical compatibility

CELLOSIZE™ QP-4400H EUR

CELLOSIZE™ QP-4400H is a medium viscosity water-soluble cellulosic polymer. This HEC is a general purposed thickener for various applications. It yield a viscosity of 4,800-6,000 cP at low addition levels.

CELLOSIZE is a hydroxylethyl cellulose polymer, nonionic and water-soluble. It is widely used as thickener, binder, emulsifier and film former. It holds moisture, suspends solids and has a good chemical compatibility. Key applications for CELLOSIZE include household cleaners, agriculture sprays, oil drilling or fracturing fluids, paper and inks, adhesives and textile back coatings. Viscosity: 4800 to 6000 cP Volatiles: 5 wt% Max Water insolubles: 0.80 wt% Max Particle size (through #20 mesh): 98% Min Water-soluble Nonionic Protective colloid Effective film former Good chemical compatibility

CELLOSIZE™ QP-52000H

CELLOSIZE™ QP-52000H has a high molecular weight water-soluble thickener. It is a efficient thickener and commonly used in adhesives and cleaning products.

CELLOSIZE™ QP-52000H is due to its high molecular weight a very efficient thickener. CELLOSIZE™ hydroxylethyl cellulose polymer, nonionic and water-soluble. It is widely used as thickener, binder, emulsifier and film former. It holds moisture, suspends solids and has a good chemical compatibility. Key applications for CELLOSIZE™ include household cleaners, agriculture sprays, oil drilling or fracturing fluids, paper and inks, adhesives and textile back coatings. Viscosity: 2,400 - 3,000 cP Volatiles: 5 wt% Max Water insolubles: 1.00 wt% Max Particle size (through #20 mesh): 98% Min Water-soluble Nonionic Protective colloid Effective film former Good chemical compatibility

CHDM D

Offered white waxy solid form. Requires a hot room or drum heater to melt the contents for removal.

Eastman™ CHDM-D is a cycloaliphatic glycol used to make saturated and unsaturated polyester resins. It is often used in conjunction with Eastman NPG™ as a glycol modifier for resins. Appearance: White waxy solid Viscosity @ 23°C: 877 cP Flash point: 167°C (333°F) Boiling point: 284-288°C (543-550°F) Melting point: 41-61°C (106-142°F) Specific gravity @ 20°C/20°C: 1.02 CAS: 105-08-8 Hardness and Flexibility balance High crystallinity Excellent humidity and corrosion resistance Good heat resistance Highly reactive hydroxyl groups Rapid esterification and cure Used in many applications such as building materials, coil coatings, contruction chemicals, machinery coatings, paints, drink packaging, polymer modification, and protective coatings.

DOWCAL™ 100

An ethylene glycol-based fluid especially requiring corrosion protection at lower glycol concentrations.

Provides excellent heat transfer performance and exceptional thermal stability in well-maintained heat transfer systems. Ethylene glycol-based fluid Offers a low acute oral toxicity, reducing contamination hazards compared to methanol alternatives. HVAC Pharmaceutical Secondary cooling and heating Freeze, burst protection Renewable energy Ground Source Heat Pumps (GSHP

DOWCAL™ N

A NSF-approved, propylene glycol-based fluid that is low in acute oral toxicity and widely used to depress freeze points in food and beverage processing and in other applications.

Dowcal™ N features a specially formulated corrosion inhibitor package and can be used for direct and indirect food additive applications. Available in various package sizes and blends. Propylene glycol based fluid Better freeze protection Better corrosion protection in hot and cold systems FDA-approved safe food additive Compatible with commonly used elastomers Long fluid life and low maintenance costs Greater cost-effectiveness Low acute oral toxicity Used to depress freeze points in food and beverage processing and in other applications

DOWFROST™

Made with DOW PuraGuard™ Propylene Glycol USP/EP, a pharmaceutical grade of monopropylene glycol with specially formulated packages of food grade industrial inhibitors that help prevent corrosion.

Regular DOWFROST™ inhibited propylene glycol (PG) DOWFROST™ is comprised of about 96% PG and 4% corrosion inhibitors. All ingredients are food safe, that is to say they are classified as GRAS (generally regarded as safe) by FDA and are approved as direct food additives. DOWFROST™ is the product of choice for the food processing industry. It is undyed and has water white appearance. DOWFROST™ offers effective heat transfer over a slightly narrower temperature range than DOWTHERM™ fluids: from 0 F to 250 F. The higher minimum recommended temperature for PG based fluids is because PG has higher viscosity and is more difficult to pump at low temperature. DOWFROST™ inhibited PG can provide freeze protection down to -60 F. DOWFROST™ is offered is various concentrations and package sizes. Color: Clear Propylene glycol-based fluid Propylene glycol-based fluid (96%) Water white Made with DOW PuraGuard™ Propylene Glycol USP/EP Low toxicity - complies with FDA and USDA regulations Operating range: 0 to 250° F for heat transfer 60° F for burst protection Heating, Ventilation & Air Conditioning (HVAC) Chill water & hydronic heating loops Geothermal (ground source heat pumps) Snow melt & Turf heating systems Solar hot water heating Fire water sprinkler systems Food processing Chilling of dairy products & beverages Beer & wine (fermentation cooling) Freezing of concentrated juices, meats, poultry & fish Refrigeration Ice skating rinks Cold storage, refrigerated warehouses & supermarkets (secondary loop) Thermal Energy Storage (TES)

DOWFROST™ Geo 20

A 20% propylene glycol solution that is intended for geothermal heat pump systems.

A ready to use solution that contains specially designed corrosion inhibitors that meet ASTM D1384 corrosion protection requirements. The low glycol content provides lower viscosity and higher heat transfer efficiency. This fluid has a freezing point of 18.5°F. Recommended Use Temperature Range: -5ºC (23ºF) to 100ºC (212ºF) Typical Properties of DOWFROST GEO 20 Fluid: Composition (% by volume) Propylene Glycol – 20 Performance Additive + Water – 80 Color – Yellow to Green Specific Gravity – 1.017 - 1.027 25 / 25ºC (77 / 77 º F) pH of Solution – 9.5 - 10.5 Reserve Alkalinity (min.) – 3.5 ml Formulated for geothermal systems Intended for use in Geothermal heating and cooling systems

DOWFROST™ HD

or beverage application.

A formulation of propylene glycol and a specially designed package of industrial corrosion inhibitors. The fluid is dyed fluorescent yellow to aid in leak detection. Not approved by the USDA or FDA for food use, and is not suitable for food...

DOWFROST™ HD inhibited propylene glycol (PG) is comprised of about 94% PG and 6% corrosion inhibitors. The lower PG content in DOWROST™ HD allows for additional corrosion inhibitors including some which are not approved by FDA as direct food additives. These additional components do not compromise toxicity fluid and provide an enhanced level of corrosion protection which is unsurpassed in the industry. DOWFROST™ HD has a fluorescent yellow color and is capable of operating at higher temperatures than regular DOWFROST™: from 0 F to 325 F. DOWFROST™ HD is intended for low toxicity, non-food processing applications and provides freeze protection down to -60 F. Dowfrost™ HD is offered is various concentrations and package sizes. Color: Green / Yellow Propylene glycol-based fluid Propylene glycol-based fluid (94%) Fluorescent yellow Increased concentration of inhibitors Not USDA/FDA approved industrial / commercial version of DOWFROST Operating range: 0 to 325° F for heat transfer -60° F for burst protection Heating, Ventilation & Air Conditioning (HVAC) Chill water & hydronic heating loops Geothermal (ground source heat pumps) Snow melt & Turf heating systems Solar hot water heating Fire water sprinkler systems Refrigeration Ice skating rinks Cold storage, refrigerated warehouses & supermarkets (secondary loop) Thermal Energy Storage (TES)

DOWTHERM™ 4000

A formulation of ethylene glycol that features one of the highest maximum use temperature of any glycol, operating temperature ranges -60°F to 350°F. The fluid is dyed fluorescent orange to aid in leak detection.

DOWTHERM™ 4000 inhibited ethylene glycol (EG) is comprised of about 92% EG and 8% corrosion inhibitors and has a bright fluorescent orange color. The lower EG content allows for a higher concentration of corrosion inhibitors which in turn means DOWTHERM™ 4000 is capable of operating at higher temperatures than DOWTHERM™ SR1 i.e. from -20°F to 350°F. This makes DOWTHERM™ 4000 a higher end, niche type product which is also capable of providing freeze protection down to -60°F. Ethylene glycol-based fluid (92%) Fluorescent orange Increased concentration of inhibitors Efficient heat transfer Operating range: -20°F to 350°F for heat transfer 60°F for burst protection Wide-temperature range operability Heating, Ventilation & Air Conditioning (HVAC) Chill water & hydronic heating loops Geothermal (ground source heat pumps) Snow melt & Turf heating systems Solar hot water heating Fire water sprinkler systems Refrigeration Ice skating rinks Cold storage, refrigerated warehouses & supermarkets (secondary loop) Thermal Energy Storage (TES)

DOWTHERM™ SR-1

A formulation of ethylene glycol and a specially designed package of industrial corrosion inhibitors with operating temperature ranges of -60°F to 250°F. The fluid is dyed fluorescent pink for leak detection purposes.

DOWTHERM™ SR1 inhibited ethylene glycol (EG) is comprised of about 95% EG and 5% corrosion inhibitors. DOWTHERM™ SR1 is the most popular EG based product within the Dow portfolio. In fact, DOWTHERM™ SR1 is the most widely recognized brand name in the industry. It offers effective heat transfer over a wide temperature range: from -20°F to 250°F and provides freeze protection down to -60°F. Color: Pink Ethylene glycol-based fluid Ethylene glycol-based fluid (95%) Fluorescent pink Efficient heat transfer Operating range: -20°F to 250°F for heat transfer 60°F for burst protection Offered in various package sizes and blends. DOWTHERM™ SR-1 25% DOWTHERM™ SR-1 30% DOWTHERM™ SR-1 35% DOWTHERM™ SR-1 40% DOWTHERM™ SR-1 45% DOWTHERM™ SR-1 50% DOWTHERM™ SR-1 60% Heating, Ventilation & Air Conditioning (HVAC) Chill water & hydronic heating loops Geothermal (ground source heat pumps) Snow melt & Turf heating systems Solar hot water heating Fire water sprinkler systems Refrigeration Ice skating rinks Cold storage, refrigerated warehouses & supermarkets (secondary loop) Thermal Energy Storage (TES)

EAA Kosher

Tautomer at room temperature, its a colorless liquid with a fruity odor.

Eastman™ EAA consists of 8% enol and 92% keto commonly used as a low color-generating copromoter to formulate unsaturated polyester resins. It is soluble in common organic solvents and water to fit many application needs. Appearance: Liquid Molecular weight: 130.14 cP Flash point: 68°C (157°F) Boiling point: 180.8°C (357.4°F) Melting point: -45°C Specific gravity @ 20°C/20°C: 1.03 CAS: 105-45-3 Kosher certified Fruity odor Low color Readily soluble in styrenated resins Used as a copromoter in paints and coatings and used as an intermediate for herbicides and insecticides.

Eastman DTBHQ Crystalline

Storage stability inhibitor - extends shelf life with minimum effects on gel time (unsaturated polyesters).

Eastman™ DTBHQ (2,5-ditert-butylhydroquinone) is a crystalline solid that has low vapor pressure and short induction periods in peroxide-catalyzed polymerizations. Insoluble in water and caustic solutions, used as an antioxidant or co-inhibitor to prevent oxidation and extend shelf life in many industrial applications. Appearance: White to tan crystals Flash point: 216°C (420°F) Melting point: 215°C (419°F) Boiling point: 321°C (610°F) Specific gravity: 1.07 CAS: 88-58-4 Scavenges radicals slowly Storage stability inhibitor with minimum effect in gel time Stabilizes against odor and color development Used as a stopping agent in rubber emulsions and anti-skinning agent in paints.

Eastman MTBHQ Dry

Secondary inhibitor (co-inhibitor) and antioxidant for nonfood fats and oils.

Eastman™ MTBHQ (mono t-butyl hydroquinone) is commonly used as a polymerization inhibitor and antioxidant in many industrial applications. Effective in higher temperatures due to its higher solubility and potency compared to unsubstituted hydroquinone. Appearance: Light tan solid Flash point: 171°C (340°F) Boiling point: 295°C (563°F) Melting point: 125°C (257°F) Specific gravity 20°C/20°C: 1.05 Molecular weight: 166.22 CAS: 1948-33-0 Very effective polymerization inhibitor Good performing antioxidant in unstable organic liquids Excellent performance as a heat and stabilizer for pressure-sensitiveness adhesives Used as a polymerization inhibitor and industrial antioxidant in many applications.

Eastman™ THQ Toluhydroquinone

Highly effective process inhibitor used in the production of highly reactive unsaturated polyesters.

Eastman™ THQ (Toluhydroquinone) is a tan to white crystalline solid that goes through similar chemical reactions as Hydroquinone. However, due to the presence of a methyl group in the ortho position, THQ becomes a highly active inhibitor in the free radical polymerization of vinyl monomers and unsaturated polyesters. Appearance: Off-white solid Flash point: 172°C (342°F) Boiling point: 279°C (534°F) Melting point: 127°C (261°F) Specific gravity: 1.3 Molecular weight: 124.13 CAS: 95-71-6 Better solubility in styrene than Hydroquinone Highly effective cook stabilizer in unsaturated polyesters Good performing antioxidant for oleates, linseed oil, and other nonfood fats and oils Used as an inhibitor, antioxidant, and intermediate manufacturing.

Elvacite® 2016

General purpose low viscosity, low molecular weight methyl methacrylate/n-butyl methacrylate copolymer.

Elvacite® thermoplastic acrylic resin copolymers or polymers are seen in solvent-applied high-quality coatings. Due to the wide range of attributes, Elvacite® is suitable for numerous applications. Glass transition temperature (°C): 59 Molecular weight: 60,000 Form: Spherical beads Particle size (Microtrac® D50): 170 - 265 microns Specific gravity: 1.13 Inherent viscosity b: 0.230-0.255 Acid number: 3.5 Moisture (% max): 0.50 Tukon hardness, knoop No. 8 Tensile strength, psi 2,300 Elongation at break (23°C, 50% RH): 2% Excellent hardness Low hazard High gloss Resistance to UV discoloration Fast dissolving Low viscosity Clear, translucent or pigmented metal coatings, heat seal lacquers, traffic marking paints, inks

Elvacite® 2697

Elvacite® 2697 is useful in clear, translucent or pigmented metal lacquers. It is a fast dissolving, low viscosity resin for lacquer and toner use. Elvacite® 2697 is non-reactive for use in reactive systems.

Elvacite® thermoplastic acrylic resin copolymers or polymers are seen in solvent-applied high-quality coatings. Due to the wide range of attributes, Elvacite® is suitable for numerous applications. Glass transition temperature (°C): 50 Molecular weight: 60,000 Form: Spherical beads Particle size (Microtrac® D50): 170 - 265 microns Specific gravity: 1.13 Inherent viscosity b: 0.230-0.255 Acid number: 3.5 Moisture (% max): 0.50 Tukon hardness, knoop no. 8 Tensile strength, psi 2,300 Elongation at break (23°C, 50% RH): 2% Fast dissolving Non-reactive for use in reactive system Low viscosity resin Low molecular weight Clear, translucent or pigmented metal coatings, heat seal lacquers, traffic marking paints, inks, reactive systems to reduce shrinkage and control viscosity.

ETHOCEL™ Standard 10 Industrial

ETHOCEL™ Standard 10 Industrial is a thickener for solvent based systems. It is an ethylcellulose with a high purity and provides consistent performance.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is mainly used in coatings, adhesives, conductive inks and electronics. Ethylcellulose functions as a thermoplastic polymer, is soluble in most common solvents and compatible with most plasticizers. ETHOCEL™ Standard 10 has a low viscosity of 10 cP and an ethoxyl content of 49%. Viscosity: 9.0 - 11.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.15% Max Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 10 Premium

ETHOCEL™ Standard 10 Premium is Pharma compliant and similar to ETHOCEL™ Standard 10 Industrial.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is mainly used in coatings, adhesives, conductive inks and electronics. Ethylcellulose functions as a thermoplastic polymer, is soluble in most common solvents and compatible with most plasticizers. ETHOCEL™ Standard 10 has a low viscosity of 10 cP and an ethoxyl content of 49%. Viscosity: 9.0 - 11.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.15% Max Pharma compliant Organosoluble Thermoplastic Highly compatible with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 100 Industrial

ETHOCEL™ Standard 100 Industrial is a solvent based cellulose ether thickener. It has a ethoxyl content of 49% and yields a viscosity of 100 cP at moderate addition level.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is mainly used in coatings, adhesives, conductive inks and electronics. Ethylcellulose functions as a thermoplastic polymer, binder and film former. It is soluble in most common solvents and compatible with most plasticizers. Viscosity: 90.0 - 110.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.15% Max Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 20 Industrial

ETHOCEL™ Standard 20 Industrial is a solvent based cellulose thickener with a viscosity of 20 cP.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is mainly used in coatings, adhesives, conductive inks and electronics. Ethylcellulose functions as a thermoplastic polymer, is soluble in most common solvents and compatible with most plasticizers. ETHOCEL™ Standard 20 an ethoxyl content of 49%. Viscosity: 18.0 - 22.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.15% Max Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 200 Industrial

ETHOCEL™ Standard 200 Industrial is solvent based thickener. It is a cellulose ether yielding a viscosity of 200 cP at moderate addition level.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is mainly used in coatings, adhesives, conductive inks and electronics. Ethylcellulose functions as a thermoplastic polymer, binder and film former. It is soluble in most common solvents and compatible with most plasticizers. Viscosity: 180.0 - 220.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.15% Max Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 300 Industrial

ETHOCEL™ Standard 300 Industrial is cellulose ether thickener for solvent based systems. It has the highest viscosity of the ETHOCEL™ range.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is mainly used in coatings, adhesives, conductive inks and electronics. Ethylcellulose functions as a thermoplastic polymer, binder and film former. It is soluble in most common solvents and compatible with most plasticizers. Viscosity: 270.0 - 330.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.15% Max Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 4 Industrial

ETHOCEL™ Standard 4 Industrial is a cellulose ether thickener for solvent based systems. With 4 cP, it has the lowest viscosity of the ETHOCEL™ range.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is mainly used in coatings, adhesives, conductive inks and electronics. Ethylcellulose functions as a thermoplastic polymer, is soluble in most common solvents and compatible with most plasticizers. ETHOCEL™ Standard 4 has a low viscosity of 4 cP and an ethoxyl content of 49%. Viscosity: 3.0 - 5.5 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.15% Max Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 45 Industrial

ETHOCEL™ Standard 45 Industrial is a cellulose ether thickener for solvent based systems. It has a ethoxyl content of 49% and a viscosity of 45 cP.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is used in coatings, adhesives, conductive inks and electronics. ETHOCEL™ has a narrow specification enabling consistent performance. Ethylcellulose functions as a thermoplastic polymer, is soluble in most common solvents and compatible with most plasticizers. Viscosity: 41.0 - 49.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.15% Max Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 45 Premium

ETHOCEL™ Standard 45 Premium is Pharma compliant and has the same properties as ETHOCEL™ Standard 45 Industrial.

ETHOCEL™ Standard 45 Premium is a solvent soluble cellulose ether thickener. It has a ethoxyl content of 49% and a viscosity of 45 cP. ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is used in coatings, adhesives, conductive inks and electronics. ETHOCEL™ has a narrow specification enabling consistent performance. Ethylcellulose functions as a thermoplastic polymer, is soluble in most common solvents and compatible with most plasticizers. Viscosity: 41.0 - 49.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.05% wt Max Residue on Ignition: 0.040% wt Max Pharma compliant with USP, NF, EP, JPE, FCC Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

ETHOCEL™ Standard 7 Industrial

ETHOCEL™ Standard 7 Industrial is an ethylcellulose polymer with a viscosity of 7 cP and yields an ethoxyl content of 49%.

ETHOCEL™ acts as binder, tough & flexible film former, water-barrier and rheology modifier. It is used in coatings, adhesives, conductive inks and electronics. ETHOCEL™ has a narrow specification enabling consistent performance. Ethylcellulose functions as a thermoplastic polymer, is soluble in most common solvents and compatible with most plasticizers. ETHOCEL™ Standard 7 has a low viscosity of 7 cP and an ethoxyl content of 49%. Viscosity: 6.0 - 8.0 mPa.s Ethoxyl content, assay: 48.0-49.5% wt Loss on drying, moisture: 2.0% wt Max Chloride (as NaCl): 0.05% Max Organosoluble Thermoplastic High compatibility with plasticizers and solvents Low sodium content Low ash content Colorless Clean burnout

Glacial Acrylic Acid

Glacial acrylic acid (GAA) is a unsaturated monocarboxylic acid. It exhibits a pungent odor, and is clear and color less.

Building block for polymer manufacturing and chemical manufacturing. Appearance: clear and colorless Physical form: liquid at >13degC Odor: pungent Molar Mass: 72.1 Assay (Gas chromatography) - min 99.5 Water Content (ASTM E 203) - max. 0.1% Color on despatch (ASTM D 1209) - max. 20 Standard Stabilization (ASTM D 3125) 200+/- 20 ppm MEHQ Easily reacts with vinyl compounds Unsaturated carboxylic acid Stabilized with 200 ppm of MEHQ Supplied in stable form

Lucite® 6751

Most optically clear of all Lucite® high molecular weight methyl methacrylate homopolymers.

Lucite® high-quality acrylic resins are designed with exact chemical properties to meet customer's needs. The production process results in pure resin that is optically pleasing. Products are seen in thousands of applications globally. Appearance: beads Rockwell Hardness (M Scale): 81 % Liminance Transmittance (0.12, 3.2mm): 92 Tensile Strength @ 23°C, 50% RH (MPa): 54 Exceptional gloss Very high surface abrasion resistance and hardness Sparkle Crystal Clarity Outstanding Ultraviolet Light Resistance Excellent Resistance to Water, Alcohol, Dilute Acids and Alkalis, Chemical Fumes and Corrosive and Oxidizing Environments

METHOCEL™ A15C

Methocel™ A15C is a methylcellulose thickener. It performs many functions simultaneously including thickening, binding, water retention and film forming. The A15C grade has a viscosity range from 1,200 to 1,800 cP.

Methocel™ A15C is a water-soluble polymer derived from cellulose. Methocel is a high purity, non-ionic cellulose ether, and performs as a rheology modifier and functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. Sodium Chloride: max 1.5% Viscosity, 2% in water, @20°C, calculated: 1200 - 1800 cP Forms a firm gel texture Reversible hot water gelation

METHOCEL™ A15LV

Methocel™ A15LV is a low viscosity methylcellulose. With a viscosity from 12 to 18 cP, it is one of the lowest in the Methocel product range. It functions as a rheology modifier in coatings and adhesives.

Methocel™ A15LV is a low viscosity water-soluble polymer derived from cellulose. Methocel is a high purity, non-ionic cellulose ether, and performs as a rheology modifier. Further it functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. The use of Methocel contributes to economic advantages, while various properties are simultaneously present and interact in combination. Methoxyl: 27.5 - 31.5% Sodium Chloride: Max 2.0% Viscosity, 2% in water, @20degC, calculated: 12 - 18 cP Water soluble Non-ionic Forms a firm gel texture Thermally gel in solution Reversible hot water gelation

METHOCEL™ A15LV Premium

METHOCEL™ A15LV Premium has the same performance properties as METHOCEL™ A15LV, except this premium product has less impurities. It can be used in pharmaceutical applications.

METHOCEL™ A15LV Premium is a water-soluble polymer derived from cellulose with a very low viscosity. Methocel is a high purity, non-ionic cellulose ether. Besides thickening, binding, Methocel functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. The use of Methocel contributes to economic advantages, due to the fact that various properties are simultaneously present. Methoxyl: 27.5 - 31.5% Loss on drying: 5.0% Max Residue on ignition: 1.5% Max Ash sulphated: 1.5% Max Sodium Chloride: Max 2.0% Viscosity, 2% in water, @20degC, calculated: 12 - 18 cP Pharmaceutical grade USP/EP/JP compliant Water soluble Non-ionic Forms a firm gel texture Thermally gel in solution Reversible hot water gelation

METHOCEL™ A4C

METHOCEL™ A4C is a low viscosity methylcellulose thickener. It yields a viscosity of 400 cP at low addition levels.

Methocel™ A4C is a water-soluble, high purity, non-ionic cellulose ether, and performs as thickener, binder and film former. Further it functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. Methocel contributes to economic advantages due to the fact that properties are simultaneously present. Methoxyl: 27.5 - 31.50% Sodium Chloride: max 2.0% Viscosity, 2% in water, @20°C, calculated: 350 - 550 cP Yields optimum performance at a lower concentration Can be added directly to aqueous systems Non-ionic pH stable Thermal gelation which is reversible

METHOCEL™ A4C Premium

METHOCEL™ A4C Premium has the same performance as METHOCEL™ A4C, except this premium product is pharmaceutical compliant.

Methocel™ A4C Premium is a water-soluble, high purity, non-ionic cellulose ether. It has a low viscosity range of 320 to 480 cps. Methocel is used as thickener, binder and film former. Further it functions as a suspending aid, stabilizer, surfactants, lubricants, protective colloids, and emulsifiers. Methocel contributes to economic advantages due to the fact that properties are simultaneously present. Methoxyl: 27.5 - 31.5% Loss on drying: 5% Max Residue on ignition: 1.5% Max pH, 2% in water: 5.0 - 8.0 Viscosity, 2% in water, @20degC, calculated: 320 - 480 cP Pharmaceutical grade Yields optimum performance at a lower concentration Can be added directly to aqueous systems Non-ionic pH stable Thermal gelation which is reversible USP/EP/JP compliant

METHOCEL™ A4M

METHOCEL™ A4M is a methylcellulose and yields a viscosity of 4,000 cP. It is used as thickener, binder, film former, and water-retention agent.

METHOCEL™ A4M is a water-soluble methylcellulose. Methocel products also function as suspension aids, surfactants, lubricant, protective colloids, and emulsifiers. Many useful properties are simultaneously present resulting in a significant economic advantage. Methoxyl: 27.5 - 31.5% Sodium Chloride: Max 1.5% Viscosity, 2% in water, @20degC, calculated: 3,500 - 5,600 cP Yields optimum performance at a lower concentration Water soluble No ionic charge pH stable Thermal gelation which is reversible

METHOCEL™ A4M Premium

METHOCEL™ A4M Premium is a pharmaceutical grade methylcellulose with the same performance properties as METHOCEL™ A4M.

METHOCEL™ A4M Premium is a water-soluble methylcellulose. It yields a viscosity of 4,000 cps. Methocel products are used as thickeners, binders, water retention aids, and also function as suspension aids, surfactants, lubricant, protective colloids, and emulsifiers. Many useful properties are simultaneously present resulting in a significant economic advantage. Viscosity, 2% in water @20°C: 2,663 - 4970 cP Loss on drying: 5% Max Residue on ignition: 1.5% Max Ash, sulphated: 1.5% Max Pharmaceutical grade USP/EP/JP compliant Yielding optimum performance at a lower concentration. Can be added directly to aqueous systems Non- ionic pH stable Thermal gelation which is reversible

METHOCEL™ E15 Industrial LV

METHOCEL™ E15 Industrial LV is an HPMC with a low viscosity of 15 cP. Solutions of this grade can be made at 10% to 15% concentration.

METHOCEL™ E15LV is water-soluble and non-ionic cellulose ether. It is often used as a thickener or binder. Methocel has various other functions which are often simultaneously present in the formulation resulting in economical advantages. It can perform as suspending aid, stabilizers, surfactants, lubricants, protective colloids, and emulsifiers. Methoxyl: 28 - 30% Viscosity, 2% in Water, @ 20degC: 12 - 18 cP Hydroxypropoxyl: 7.0 - 12.0% Forms a semi firm gel texture Thermally gel in solution Reversible hot water gelation

METHOCEL™ E5 Premium LV

METHOCEL™ E5 Premium LV is a Hydroxypropyl Methylcellulose (HPMC) thickener which yields a very low viscosity of 5 cP. It is a pharmaceutical grade.

METHOCEL™ E5 Premium LV is a water-soluble polymer derived from cellulose. This pharmaceutical grade can be used in Industrial applications. Methocel products are used as thickeners, binders, water retention aids, and also function as suspension aids, surfactants, lubricity aids, and emulsifiers. Since various properties are present in a formulation Methocel is an economical preferred choice versus other polymers. Viscosity, 2% in water @20°C: 4.0 - 6.0 cP Methoxyl: 28.0 - 30.0% Hydroxypropoxyl: 7.0 - 12.0% Loss on Drying: 5.0% Max Residue on Ignition: 1.5% Max pH, 2% in water: 5.0 - 8.0 Compliant with US, JP, EUR Pharmacopeia U.S. FDA Gras This grade can be used in Industrial applications.

METHOCEL™ J12MS

METHOCEL™ J12MS is a surface treated HPMC resulting in delayed viscosity build up to 12,000 cPs. It has one of the highest substitution levels.

METHOCEL™ J12MS is a hydroxypropyl methylcellulose (HPMC). It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products function as thickener, binder and rheology modifier. The combination of properties present simultaneously brings economic advantages versus other polymers. Methoxyl: 16.5 - 20.0% Hydropropoxyl: 23.0 - 32.0% Viscosity, 2% in water @20°C: 10,000 - 16,500 cPs

METHOCEL™ J75MS

METHOCEL™ J75MS is a Hydroxypropyl Methylcellulose (HPMC) thickener with very high substitution. Is has a viscosity range from 60,000 to 75,000 cPs at low addition levels. This grade is surface treated with a slow viscosity build up.

METHOCEL™ J75MS is a hydroxypropyl methylcellulose (HPMC). It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products function as thickener, binder and rheology modifier. The combination of properties present simultaneously brings economic advantages versus other polymers. Methoxyl: 16.5 - 20.0% Hydroxypropoxyl: 23.0 - 32.0% Viscosity, 2% in water @20°C: 60,000 - 90,000 cP Can be added directly to aqueous systems No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ K100LV

METHOCEL™ K100LV is a hydroxypropyl methylcellulose (HPMC) thickener with low substitution. It has a low viscosity of 100 cP at low addition levels.

METHOCEL™ K100LV is a low viscosity methylcellulose polymer. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 80 - 120 cP Moisture, as packaged: 3.0 Max Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ K15M

METHOCEL™ K15M is a HPMC thickener with low substitution. It yields a viscosity of 15,000 cP and forms a soft gel texture. This Methocel has the highest gelation temperature of 70°C-90°C (158°F-194°F).

METHOCEL™ K15M is a hydroxypropyl methylcellulose. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 10,000 - 18,000 cP Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ K15M Food Grade

METHOCEL™ K15M Food Grade is the same as K15M, but is compliant with international Food standards.

METHOCEL™ K15M Food grade is a hydroxypropyl methylcellulose. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 11,250 - 21,000 cPs Food compliancy; FCC, EC, FAO/WHO, GRAS, U.S. FDA Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling Can be used in Industrial applications.

METHOCEL™ K15MS

METHOCEL™ K15MS is similar to K15M, except it is surface treated for a retarded dissolution.

METHOCEL™ K15M is a hydroxypropyl methylcellulose. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 10,000 - 18,000 cP Delayed dissolution Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

METHOCEL™ K4M

METHOCEL™ K4M ia a hydroxypropyl ethylcellulose (HPMC) thickener with a low substitution. It has a viscosity of 4,000 cP at low addition levels.

METHOCEL™ K4M is a hydroxypropyl methylcellulose. It is a water-soluble, high-purity, non-ionic cellulose ether. Methocel products are used as thickeners, binders, film formers, and water retention agents. The combination of properties in a formulation bring economic advantages versus other polymers. Methoxyl: 19.0 - 24.0% Hydroxypropoxyl: 7.0 - 12.0% Viscosity, 2% in water @20°C: 12,000 - 21,000 cP Sodium Chloride: 2.0 Max Water soluble No ionic charge pH stable Thermal gelation Gels goes back into solution upon cooling

POLYOX™ WSR 1105

POLYOX™ WSR 1105 is a polyethylene oxide thickener. It is a water-soluble resin with a viscosity of 8,800 to 17,600 cP.

POLYOX™ WSR 1105 has a molecular weight of 900,000 and has the highest viscosity in the POLYOX range. It is widely used as binder, lubricant, thickener and water retention aid. It forms flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Further it provides wet tack in paper products. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 8800- 17600 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity

POLYOX™ WSR 205

POLYOX™ WSR 205 is a water-soluble thickener with a molecular weight 600,000. The viscosity ranges from 4,500 to 8,800 cP.

POLYOX™ WSR 205 is a polyethylene oxide with a viscosity of 4500 - 8800 cP. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 6800 - 8800 cP pH at 25degC: 8.0 - 10.0 Loss on drying: 0.0 - 1.0 WT% Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR 301

POLYOX™ WSR 301 is a water-soluble resin with a high molecular weight of 4,000,000.

POLYOX™ WSR 301 is a polyethylene oxide (PEO) with a viscosity of 1650 - 5500 cP. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Further it provides wet tack in paper products. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper, adhesives, building and construction. In Concrete, It works as a flow aid in pumped, lightweight, spray and underwater concrete. Viscosity: 1650 - 5500 cP pH at 25degC: 8.0 - 10.0 Loss on drying: 0.0 - 1.0 WT% Silicon dioxide: 0.8 - 3.0 WT% High binding efficiency Crosslinkable Viscoelastic Flow and pumpability aid Lubrication aid Thermoplastic Low toxicity Nonionic

POLYOX™ WSR 301 Fine Powder NF

POLYOX™ WSR 301 Fine Powder NF has same characteristic as POLYOX™ WSR 301, except this grade is pharma compliant.

POLYOX™ WSR 301 is a polyethylene oxide with a viscosity of 1650 - 5500 cP. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 1650 - 5500 cP pH at 25degC: 8.0 - 10.0 Loss on drying: 0.0 - 1.0 WT% Silicon dioxide: 0.8 - 3.0 WT% National Formulary Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR 303

POLYOX™ WSR 303 has a molecular weight 7,000,000 and the viscosity ranges from 7,500 to 10,000 cP.

POLYOX™ is a polyethylene oxide thickener and water-soluble. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 7500 - 10000 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR 308

POLYOX™ WSR 308 is a polyethylene oxide thickener. It has a high molecular weight of 8,000,000 and a viscosity range of 10,000 to 15,000.

POLYOX™ is a water-soluble resin and used as binder, lubricant, thickener and water retention aid in various applications. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. POLYOX™ WSR 308 has the highest molecular weight of the POLYOX range. Viscosity: 10000 - 15000 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic Available in 140 lb and 960 lb drums

POLYOX™ WSR Coagulant

POLYOX™ WSR Coagulant is a PEO thickener with a molecular weight of 5,000,000.

POLYOX™ WSR Coagulant is a water-soluble polymer with a viscosity range from 5500 to 7500 cP. POLYOX is widely used as binder, lubricant, thickener and water retention aid. Viscosity: 5500 - 7500 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N10

POLYOX™ WSR N10 is a polyethylene oxide and water soluble thickener. It has a molecular weight of 100,000 and yields a viscosity of 12 to 50 at moderate addition levels.

POLYOX™ are water-soluble resins with a high molecular weight. They provide lubricity, binding, water retention, thickening and film forming properties. Main applications are in agriculture, adhesives, paper & pulp, industrial cleaners, ceramics and electronics. POLYOX™ WSR N10 has the lowest molecular weight of the POLYOX™ range and used where lower viscosity is required. It is a recommended grade for seed coatings. Viscosity: 30 - 50 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N10 100 Mesh

POLYOX™ WSR N10 100 Mesh has the same properties than POLYOX™ WSR N10 100, except this has finer particles.

POLYOX are water-soluble polyethylene oxide resins with a high molecular weight. They provide lubricity, binding, water retention, thickening and film forming properties. Main applications are in agriculture, adhesives, paper & pulp, industrial cleaners, ceramics and electronics. POLYOX™ WSR N10 mesh has the lowest molecular weight of the POLYOX range and used where lower viscosity is required. This mesh grade has a smaller particle size. Viscosity: 30 - 50 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N12K

POLYOX™ WSR N12K is a water-soluble polymer and has a molecular weight of 1,000,000. It yields a viscosity of 400 to 800 cP at 2% addition level.

POLYOX™ are water-soluble polyethylene oxide resins with a high molecular weights. They provide lubricity, binding, water retention, thickening and film forming properties. Main applications are in agriculture, adhesives, paper & pulp, industrial cleaners, ceramics and electronics. POLYOX™ WSR N12K has a relative low viscosity of 400-800 cP. Viscosity: 400 - 800 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N3000

POLYOX™ WSR N3000 is a water-soluble resin with a relative high molecular weight of 400,000. It yields a viscosity of 2,250 to 4,500 at moderate addition levels.

POLYOX™ WSR N3000 is typically used in fluorescent lamp phosphors or as phosphor binders in cathode ray tubes. POLYOX™ is a polyethylene oxide thickener and water-soluble. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 2,250 - 4,500 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N3000 LS

POLYOX™ WSR N3000 LS has the same characteristics as POLYOX™ WSR N3000, except LS version has a low silicon dioxide level of less than 1.5WT%.

POLYOX™ WSR N3000 is typically used in fluorescent lamp phosphors or as phosphor binders in cathode ray tubes. POLYOX™ is a polyethylene oxide thickener and water-soluble. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 2,250 - 4,500 cP Silicon dioxide: 0.0 - 1.5 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N60K

POLYOX™ WSR N60K is a PEO polymer with a molecular weight of 2,000,000.

POLYOX™ WSR 60K is a polyethylene oxide with a viscosity of 2000 - 4000 cP in a 2% aqueous solution. It is widely used as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Most common applications are ceramics, industrial cleaning products, electronics, mining, paper and adhesives. Viscosity: 2000 - 4000 cP Silicon dioxide: 0.8 - 3.0 WT% Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N750

POLYOX™ WSR N750 is a water-soluble thickener with a molecular weight of 300,000. It has a viscosity range of 600 to 1,200 in a 5% solution.

POLYOX™ WSR N750 is widely used as seed coatings, wet-tack in paper adhesives, thickener in industrial cleaning products and coatings and paint removers for building and construction. In fluorescent lamp phosphors the N750 is used as binder. POLYOX™ is a polyethylene oxide thickener and water-soluble. Is functions as binder, lubricant, thickener and water retention aid. They form flexible, and tough film which are resistant to oils and greases. The viscoelastic properties enable reduction of spattering and misting. Due to its thermoplasticity PEOs can be extruded, injection molded or casted. Viscosity: 600 - 1,200 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

POLYOX™ WSR N80

POLYOX™ WSR N80 is a water-soluble PEO thickener with a molecular weight of 200,000. It has a low viscosity of 65 to 115 cP.

POLYOX™ are water-soluble polyethylene oxide resins with a high molecular weights. They provide lubricity, binding, water retention, thickening and film forming properties. Main applications are in agriculture, adhesives, paper & pulp, industrial cleaners, ceramics and electronics. POLYOX™ WSR N80 is one of the lower molecular weight grades of the POLYOX™ range. Viscosity: 65 - 115 cP Silicon dioxide: 0.8 - 3.0 WT% Particle size thru 10 mesh: 100 Min Particle size thru 20 mesh: 96-100 Water-soluble High binding efficiency Crosslinkable Viscoelastic Thermoplastic Low toxicity Nonionic

Sodium PYRION™ 40%

Antimicrobial preservative (sodium pyrithione) used in a variety of water-based functional fluids and coatings to protect against micro-organisms.

Sodium Pyrion is highly effective against micro-organisms. Often used in water based fluids such as metal working, hydraulic, industrial lubricants, and water based latex paint applications. The pyrithione chemistry is often used when stability and low leachability is critical. Able to be used in low doses, reduces treatment costs and can be used in post treatment or metalworking fluid concentrates. Appearance: Clear, yellow-brown liquid Specific Density: 1.10 - 1.24 g/ml pH-value : 1.19 - 1.24 g/ml Molecular weight: 149.15 Thermal stability: 250°C CAS number: 3811-73-2 EPA registered Low treat rates Non-leaching results with long term protection Ease of application in aqueous form Due to the effectiveness at low treat rates, Sodium Pyrion saves formulators time and money by gaining more antimicrobial effectiveness, while using less.

Trilene® 65

Low molecular weight liquid Ethylene Propylene (EPDM) terpolymer with 10% diene content for use in rubber, coatings and adhesives.

Trilene® 65 is a liquid EPDM terpolymer that is used as an additive in rubber compounds and works well in peroxide-cured systems to reduce viscosity. It acts as a reactive plasticizer in rubber compounds without any significant loss of hardness or other mechanical properties. In coatings & adhesives Trilene® 65 is used as a nonpolar, non crystalline elastomeric material that provides strong adhesion to a variety of substrates. Additionally, Trilene® 65 demonstrates low permeability to gases and water vapor, superior impact resistance and high flexibility at low temperatures. Ethylene/Propylene: 50/50 Degree of Unsaturation (% Diene): 10% Type of Diene: DCPD Color: Pale Yellow Specific Gravity: 0.86 Molecular Weight by GPC (Da): 47,000 Brookfield Viscosity (cP, RVT #7 at 60°: 1,900,000 Brookfield Viscosity (cP, RVT #7 at 100°: 177,000 Volatiles at 100ºC (212ºF): <0.5% Easy to process Non extractable Maintains mechanical properties Non-volatile Hydrophobic with low surface energy Compatible with other polymers, oils and solvents Flexible at low temperatures Excellent resistance to moisture, UV light, ozone and chemical degradation Adhesion to various substrates without the use of a primer Good impact resistance Rubber belts and hoses for Aerospace and Automotive Building & Construction Wire & Cable Weather stripping Conveyer belts Roof coatings Elastomeric coatings Marine coatings Anticorrosion coatings Barrier coatings that need permeability to air, water and chemicals Elastomeric sealants & adhesives

Trilene® 67

Low molecular weight liquid Ethylene Propylene (EPDM) terpolymer with 9.5% diene content for use in rubber, coatings and adhesives.

Trilene® 67 is a liquid EPDM terpolymer that is used as an additive in rubber compounds and works well in sulfur-cured systems to reduce viscosity. It acts as a reactive plasticizer in rubber compounds without any significant loss of hardness or other mechanical properties. In coatings & adhesives Trilene® 67 is used as a nonpolar, non crystalline elastomeric material that provides strong adhesion to a variety of substrates. Additionally, Trilene® 67 demonstrates low permeability to gases and water vapor, superior impact resistance and high flexibility at low temperatures. Ethylene/Propylene: 46/54 Degree of Unsaturation (% Diene): 9.5% Type of Diene: ENB Color: Pale Yellow Specific Gravity: 0.86 Molecular Weight by GPC (Da): 39,000 Brookfield Viscosity (cP, RVT #7 at 60°: 900,000 Brookfield Viscosity (cP, RVT #7 at 100°: 128,000 Volatiles at 100ºC (212ºF): <0.5% Easy to process Non extractable Maintains mechanical properties Non-volatile Hydrophobic with low surface energy Compatible with other polymers, oils and solvents Flexible at low temperatures Excellent resistance to moisture, UV light, ozone and chemical degradation Adhesion to various substrates without the use of a primer Good impact resistance Rubber belts and hoses for Aerospace and Automotive Building & Construction Wire & Cable Weather stripping Conveyer belts Roof coatings Elastomeric coatings Marine coatings Anti-corrosion coatings Barrier coatings that need permeability to air, water and chemicals Elastomeric sealants & adhesives

Trilene® 77

Low molecular weight Ethylene Propylene (EPDM) terpolymer with 10.5% diene content for use in rubber, coatings and adhesives.

Trilene® 77 is a crystalline waxy EPDM terpolymer that is used as an additive in rubber compounds and works well in sulfur-cured systems to reduce viscosity. It acts as a reactive plasticizer in rubber compounds without any significant loss of hardness or other mechanical properties. In coatings & adhesives Trilene® 77 is used as a nonpolar, non crystalline elastomeric material that provides strong adhesion to a variety of substrates. Additionally, Trilene® 77 demonstrates low permeability to gases and water vapor, superior impact resistance and high flexibility at low temperatures. Trilene® 77 is easier to handle during mixing compared to Trilene® 65 and 67 since it is a solid at room temperature. Ethylene/Propylene: 74/26 Degree of Unsaturation (% Diene): 10.5% Type of Diene: ENB Color: Pale Yellow, Waxy solid Specific Gravity: 0.86 Molecular Weight by GPC (Da): 27,000 Brookfield Viscosity (cP, RVT #7 at 60°: 800,000 Brookfield Viscosity (cP, RVT #7 at 100°: 102,000 Volatiles at 100ºC (212ºF): <0.5% Easy to process East to weigh before mixing Non extractable Maintains mechanical properties Non-volatile Hydrophobic with low surface energy Compatible with other polymers, oils and solvents Flexible at low temperatures Excellent resistance to moisture, UV light, ozone and chemical degradation Adhesion to various substrates without the use of a primer Good impact resistance Rubber belts and hoses for Aerospace and Automotive Building & Construction Wire & Cable Weather stripping Conveyer belts Roof coatings Elastomeric coatings Marine coatings Anti-corrosion coatings Barrier coatings that need permeability to air, water and chemicals Elastomeric sealants & adhesives

Tyzor® PITA SM

Tyzor™ PITA SM is a mixture of titanium ethyl acetoacetate complex with 100% active content and methyl-trimethoxy silane.

Tyzor PITA-SM is designed as a curing agent for silicone based sealants and adhesives. Its high reactivity at low temperatures enables it to react with common functional groups such as R-OH, M-OH, SiOH, or R-COOH to effect cure rate, crosslinking and adhesion promotion. TiO2 Content: ca. 15.2% Active Content: ca. 80% Color: Yellow to Orange Density (20 C): ca. 1.08 g/ml Viscosity (20 C): ca. 8 mPa*s Pour Point: < -10 C Boiling Point: ca. 102 C (Solvent) Flash Point: ca. 32 C Solubility in Solvents: Miscible in most organic solvents Solubility in water: Decomposes Tyzor PITA-SM in silicone sealants and adhesives promotes adhesion, crosslinks silanes, increases cure rate and acts as a drying agent. It can also provide these benefits when used with silanol end-capped polymers such as polypropylene oxides, acrylates, or polyurethanes. They can also be used as additives in paints to cross-link functional polymers or binders, act as binders or promote adhesion.

UCARTHERM™ HTF PM 6141

A formulation of ethylene glycol and specifically designed inhibitor packages with operating temperature ranges of -60°F to 250°F.

Manufactured with 100% virgin ethylene glycol and specifically formulated with heavy-duty industrial inhibitor packages that prevent corrosion, these fluids are widely used for closed-loop, process heating and process cooling. The inhibitors are easily maintained, long lasting and replenishable, which means intervals between fluid change-outs are extended and fluid expense is minimized. Ethylene glycol-based fluid Wide temperature range operability HVAC; Oil & Gas; Immersion freezing; Process cooling; Process heating; Solar heating; Radiant Heating; Thermal Energy Storage; Geothermal; Snow Melt Systems; Fermentation Cooling

Unilink 4200

Aromatic diamine used in polyurea, polyurethane foam elastomer applications.

Unilink 4200 is an easy to handle di-functional aromatic diamine that is low in toxicity, relatively insensitive to moisture and compatible with a wide range of co-curative and other components. Due to relatively low reactivity, Unilink 4200 can be used in TDI or MDI formulations, and cross-linking can be controlled by adding higher functioning polyols Appearance Clear: light-to-dark-brown liquid Hydroxyl number: 362 Flash point, PMCC, °C (°F), min: 161 (321.8) Specific gravity @ 26.7 °C (80 °F): 0.98 to 0.99 Density, g/cm3 (lb/gal): 0.995 (8.3 ) Water content, ppm, max: 500 Molecular weight: 310 Equivalent weight, min: 153 Easy to handle and environmentally friendly liquid (Ames negative) Low moisture sensitivity Compatible with polyurethanes, most polyols, and curatives Excellent storage stability in polyether and polyester polyols. Cures TDI and MDI coating compounds at ambient temperature Polyurea Systems Unilink 4200 improves gel time, flow and allows the polyurea coatings to be processed by spray or pour techniques. Adhesion to the substrate and surface finishes improve, and so does bonding between coats. Cured systems have excellent physical properties and exhibit significant improvements in impact resistance and low-temperature performance. Flexible foams Unilink 4200 improves tensile, tear and load-bearing properties In standard TDI and high-resilience slabstock foam systems, often at lower foam densities, and significantly improves polyester foam tear strength and load-bearing. It reduces density and softens cold-molded foams, producing higher tensile strength, tear and elongation, along with improved mold flow and decreased de-mold times. Rigid foams Rigid foams cured with UNILINK 4200 show significant improvements in compressive strength and dimensional stability with reduced friability, a higher percentage of closed cells and lower K-factor. Compressive strength improves by up to 100% in PIR foams, and dimensional stability also is significantly enhanced. Coatings, Adhesives, Sealants & Elastomers Formulations cured with UNILINK 4200 adhere better and develop smoother surface finishes.

WALOCEL™ CRT 100 GA

WALOCEL™ CRT 100 GA is a carboxymethyl cellulose (CMC) in granular form with a low viscosity of 100 cP. It provides a crystal clear solution free of fibers.

WALOCEL™ CRT 100 GA is a low viscosity CMC. This granular grade can be added directly to water, and has a slow agitation. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. Viscosity, Brookfield, LVT, SP.3, 30 RPM, 1% aqueous solution (dry basis), 25°C: 110 - 160 cP Substitution, degree of 0.82 — 0.95 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films Improving stickiness in water-based adhesives. In batteries used as binder for anode components. Offers stability during ceramic forming and in the oven.

WALOCEL™ CRT 100 PA

WALOCEL™ CRT 100 PA is similar to CRT 100 GA, except this is a powder grade. It can be blended with other dry ingredients prior to addition to water.

WALOCEL™ CRT 100 PA is a low viscosity CMC. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. Viscosity, Brookfield, LVT, SP.3, 30 RPM, 1% aqueous solution (dry basis), 25°C: 110 - 160 cP Substitution degree: 0.82 — 0.95 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature Provides a clear solution High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films Improving stickiness in water-based adhesives. In batteries used as binder for anode components. Offers stability during ceramic forming and in the oven.

WALOCEL™ CRT 1000 GA

WALOCEL™ CRT 1000 GA is a granular CMC with a viscosity of 1,000 cP.

WALOCEL™ CRT 1000 GA is a low viscosity CMC. This granular grade has a slow agitation. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. It provides a clear solution. Viscosity, Brookfield, LVT, SP.2, 30 rpm, 2% aqueous sol. (dry basis), 25°C: 550 - 800 cP Substitution degree: 0.82 — 0.95 pH Value, 1% aqueous solution 6.5 — 8.5 Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films Recommended grade in paper and ceramic applications.

WALOCEL™ CRT 1000 PA 07

WALOCEL™ CRT 1000 PA 07 has similar properties than CRT 1000 GA, except this is a powder grade.

WALOCEL™ CRT 1000 PA 07 is a low viscosity CMC with a substitution degree of 0.7. This powder grade can be blended with other ingredients before dissolving in water. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. Walocel with low viscosity grades provide clear solutions. Viscosity, Brookfield, LVT, SP.2, 30 rpm, 2% aqueous sol. (dry basis), 25°C: 300- 600 cP Substitution degree: 0.65 — 0.80 pH Value, 1% aqueous solution 6.5 — 8.5 Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films

WALOCEL™ CRT 2000 PA

WALOCEL™ CRT 2000 PA is a carboxymethyl cellulose (CMC) powder with a viscosity of 2,000 cP.

WALOCEL™ CRT 2000 PA is a CMC in powder form. This low viscosity powder grade provides a clear solution. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. Viscosity, Brookfield, LVT, SP.2, 30 rpm, 2% aqueous sol. (dry basis), 25°C: 1900 - 2800 cP Substitution degree: 0.82 — 0.95 pH Value, 1% aqueous solution 6.5 — 8.5 Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films

WALOCEL™ CRT 20000 GA

WALOCEL™ CRT 20000 GA is a granular carboxymethyl cellulose (CMC) with a viscosity of 20,000 cP.

WALOCEL™ CRT 20,000 GA is a granular CMC grade with a slow agitation. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. It provides a clear solution. Viscosity, Brookfield, LVT, SP.3, 30 RPM, 1% aqueous solution (dry basis), 25°C: 1,900 - 2,600 cP Substitution, degree of 0.75 — 0.85 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films

WALOCEL™ CRT 30 PA

WALOCEL™ CRT 30 PA has the lowest viscosity of the WALOCEL™ product range. It yields a viscosity of 30 cP.

WALOCEL™ CRT 30 PA is a powder which can be blended with other solid ingredients prior to the addition of water. It is a thickener and binder, has excellent water-binding and film-forming properties in adhesives, batteries and ceramics. Viscosity, Brookfield, LVT, SP.3, 30 RPM, 1% aqueous solution (dry basis), 25°C: 25 - 30 cP Substitution, degree of 0.82 — 0.95 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films

WALOCEL™ CRT 30000 GA

WALOCEL™ CRT 30000 GA is a granular carboxymethyl cellulose (CMC) with a high viscosity of 30,000 cps at 2% concentration.

WALOCEL™ CRT 30000 GA is high viscosity thickener. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. Viscosity, Brookfield, LVT, SP.4, 30 RPM, 1% aqueous solution (dry basis), 25°C: 3,000 - 4,000 cP Substitution, degree of 0.82 — 0.95 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films The non-toxicity of Walocel™ CRT makes it an ideal polymer to formulate gels.

WALOCEL™ CRT 40000 GA

WALOCEL™ CRT 40000 GA is a high viscosity granular CMC of 40,000 in a 2% aqueous solution.

WALOCEL™ CRT 40000 GA is high viscosity thickener. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. Viscosity, Brookfield, LVT, SP.4, 30 RPM, 1% aqueous solution (dry basis), 25°C: 4,000 - 5,000 cP Substitution, degree of 0.82 — 0.95 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films The non-toxicity of Walocel™ CRT makes it an ideal polymer to formulate gels.

WALOCEL™ CRT 40000 PA

WALOCEL™ CRT 40000 PA is similar to CRT 40000 GA, except this is a powder grade.

WALOCEL™ CRT 40000 PA is high viscosity thickener. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. This Powder grade can be blended with other dry ingredients prior to addition to water. Viscosity, Brookfield, LVT, SP.4, 30 RPM, 1% aqueous solution (dry basis), 25°C: 4,000 - 5,000 cP Substitution, degree of 0.82 — 0.95 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films

WALOCEL™ CRT 60000 GA

WALOCEL™ CRT 60000 GA is a granular carboxymethyl cellulose (CMC). With 60,000 cP it has the highest viscosity of all WALOCEL™ products.

WALOCEL™ CRT 60000 GA is high viscosity binder and thickener. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. Viscosity, Brookfield, LVT, SP.3, 30 RPM, 0.5% aqueous solution (dry basis), 25°C: 1,100 - 2,000 cP Substitution, degree of 0.7 — 0.8 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films The non-toxicity of Walocel™ CRT makes it an ideal polymer to formulate gels.

WALOCEL™ CRT 60000 PPA 07

WALOCEL™ CRT 60000 PPA 07 has the same properties as CRT 60000 GA, except it is a powder grade which can be blended with other ingredient prior to the addition to water.

WALOCEL™ CRT 30000 PPA 7 is a high viscosity thickener. Walocel is used as binder, thickener, gelling agent, stabilizer, emulsifier, crystallization inhibitor, protective colloid, film former, plasticizer and provide green strength. Viscosity, Brookfield, LVT, SP.3, 30 RPM, 0.5% aqueous solution (dry basis), 25°C: 1,100 - 2,000 cP Substitution, degree of 0.7 — 0.8 pH Value, 1% aqueous solution: 6.5 — 8.5 Total salt content, dry basis 0.50 Max Anionic Water soluble at any temperature High surface tension, less foam formation Excellent viscosifier; reversible viscosity decrease upon heating Stable in a wide pH-range (pH 3.5 – 12) Compatible with nearly all other hydrocolloids No odor and no taste Forming fat, oil and organic solvent resistant films The non-toxicity of Walocel™ CRT makes it an ideal polymer to formulate gels.