Multifunctional Diesel Fuel Additive, contains cold flow improver, wax antisettling and deicer additives for environments as cold as -30°F.
HiTEC® 18536X is a winter performance diesel additive for use in potential freeze-up environments. Provides enhanced fluidity for environments around -30°F. HiTEC® 18536X also meets USA EPA 40CFR80.591A ensuring the additive contains less than 15ppm sulfur. Appearance: Amber Liquid Density, lbs/gal.: 7.43 Specific Gravity @ 15.6/15.6°C: 0.8925 Viscosity @ 40°C: 3 Flash Point, °C (C): 48 min. Max Handling Temp: 40°C Shelf Life: 24 months Improves low temperature operability in a range of common fuels Lowers CFPP (cold filter plugging point) without adversely affecting energy content of the fuel. Reduces risk of fuel line Freeze-Up HiTEC® 18536X should be blended into base fuel at or above 10-15°F than fuels cloud point. HiTEC® is a trademark of Afton Chemical Corporation.
Winter diesel fuel additive, contains cold flow improver, wax antisettling and deicer additives for environments as cold as -5°F.
HiTEC® 18933DN is a winter performance diesel additive for use in potential freeze-up environments. Provides enhanced fluidity for environments around -5°F. Appearance: Clear to hazy yellow amber liquid Density, lbs/gal.: 7.55 Specific Gravity @ 15.6/15.6°C: 0.906 Viscosity @ 40°C: 7.2 Flash Point, °C (C): 40 min. Improves low temperature operability in a range of common fuels Lowers CFPP (cold filter plugging point) without adversely affecting energy content of the fuel Reduces risk of fuel line Freeze-Up Reduces wax dropout where fuel is stored below cloud point Recommended dosage rate of the HiTEC® 18933DN is 1 gallon per 3,000 gallons of diesel. Treat rate can be doubled or tripled for severe cold conditions. HiTEC® is a trademark of Afton Chemical Corporation.
Winter diesel additive, contains detergent, cold flow improver, wax antisettling, deicer, thermal stability and corrosion inhibitor additives.
HiTEC® 18940G is a multifunctional diesel performance additive for use in cold weather environments. Improves winter operability by inhibiting wax formation and enhancing cold flow capabilities while also ensuring injector cleanliness by controlling deposit formation. Density, lbs/gal.: 7.58 Specific Gravity @ 15.6/15.6°C: 0.9091 Viscosity @ 40°C: 13.1 Flash Point, °C (C): 43 min. Max Handling Temp: 40°C Shelf Life: 24 months Improves low temperature operability in a wide range of fuels by lowering the CFPP and pour point Improves fuel filterability to prevent premature fuel filter plugging Reduces risk of fuel line freeze-up Scalable to clean injector deposits Compatible with modern diesel and typical biodiesel blends HiTEC® 18940G treat rates will vary on desired performance and base fuel.
Hindered phenolic antioxidant that provides excellent color protection during polymerization and manufacturing of polyamide fibers, molded articles, and films.
LOWINOX® HD98 is a high performance hindered phenolic antioxidant designed to stabilize polyamides. To protect polyamide fibers, it can be added to the polymer melt in the final stages of polymerization. LOWINOX® HD98 can also be added prior to polymerization to impart excellent color protection during manufacturing, spinning, and heat setting. Appearance: White powder Melting Point: 156-163 °C Molecular Weight: 637 g/mol Bulk Density: 450 kg/m³ Excellent color protection during polymerization and manufacturing Resistant to extraction Polyamide fibers, molded articles, and films
Heavy-duty anti-seize and extreme-pressure lubricant formulated to assure absolute parts protection against seizure, galling, and corrosion in fresh and salt water environments.
Mariner's Choice offers unparalleled resistance to water washout and the best protection in continuous high-moisture environments, both above and below water lines. Color: Black-Gray Temperature Range, °F (°C): -297°F to 2,450°F (-183°C to 1,343°C) Thickener Type: Calcium Complex Particle Size, mil (microns): 3.5 maximum (75 μ) Density (g/cm3): 1.31 to 1.39 Flash Point, °F (°C): >475°F (246°C) Salt Fog Test, hrs.: 4,000 Copper Corrosion Test @ 212°F (100°C), 24 hrs.: No Corrosion Worked Penetration, 60 Strokes @ 77°F (25°C): 260-310 NLGI Grade: 1/2 Dropping Point, °F (°C): 572 (300) Torque Coefficient, k factor: 0.11 Water Washout, % loss: @ 100°F: <1.00 @ 175°F: <2.75 Bearing Rust Test (ASTM D-1764): Pass Four Ball EP: Load Wear Index: 127.3 Last non-seizure load (scar): 100 kgf (0.45 mm) Last Seizure Load (scar): 620 kgf (2.21 mm) Weld Load: 800 kgf Fretting Wear @ 73°F (23°C), 22 hrs., mg loss: 7.15 Prevents seizure at temperatures up to 2,450°F (1,343°C) Prevents galvanic corrosion in salt and fresh water environments Superior resistance to water washout and water spray Excellent extreme pressure lubricating properties Low torque factor Compatible with soft metals Contains no copper Tested to MIL-A-907E Available in the following sizes: • NMCBT-8 (8 oz. brush top can) • NMCBT-16 (1 lb. brush top can) • NMC-42 (42 lb. pail) Bilge pumps, screw shafts, prop shaft bearing housing, winches, cables, anchor lines, porthole studs, rigging and hoist cables, Steel mills, suspension bridges, wind turbines, offshore rigging and other applications exposed to harsh salt water and fresh water conditions